PrepAMT Academy

ORAL AND PRACTICAL · FLASHCARDS · WRITTEN FOR THIS PAGE

FAA A&P oral test practice questions

30 flashcards to practice the spoken half of the FAA A&P, 10 for each of General, Airframe and Powerplant. Read the question, say your answer out loud, then open the card. They are practice for the oral, not the questions an examiner will ask: those are picked by the FAA’s Mechanic Test Generator, and an applicant may not know them before the test begins.

The oral’s rules read from FAA-G-ACS-1 and the ACS.

01 GENERAL ORALAMG · 10 CARDS

FAA A&P General oral practice questions

Written from FAA-H-8083-30B, across the General subject areas. Every card ends with the handbook page its answer comes from.

Q.01

An owner keeps every one of his logbooks in a bag behind the seat, so they always travel with the airplane. What would you advise him, and why?

Take them out and keep them in a filing system in the office. Apart from the Form 337 that has to stay aboard when a fuel tank is installed in the cabin or cargo area, nothing requires the maintenance records to be carried in the airplane. There are good reasons not to: the 2 biggest concerns are records that get damaged and records that get lost, and the logs are much safer from both in the office than in a bag in the airplane. (FAA-H-8083-30B, ch. 2, p. 2-22)

Q.02

A fuel quantity indicator is calibrated for Jet A, but the airplane has been fueled with Jet B. A note printed with the fuel density chart covers this. How do you get the real fuel weight from the gauge?

Read the note before trusting the number. The indicator reads correctly only with Jet A or Jet A1, and with other fuels you multiply the pounds it shows by a factor: 0.99 for Jet B (JP-4), or 0.98 for 100/130 avgas. So 12,000 pounds indicated with Jet B means about 11,880 pounds aboard. The correction is there because the fuels differ in average specific gravity, which is what the chart beside the note sets out. (FAA-H-8083-30B, ch. 4, p. 4-26)

Q.03

An airplane speeds up along a straight line. How do you work out how many G that acceleration puts on the pilot?

First find the acceleration: the change in speed divided by the time it took. If the speed is in miles per hour, multiply by 1.467 to get feet per second, so the answer is in feet per second per second. Then divide by 32.2, the acceleration due to gravity. A jet going from 60 to 150 mph in 30 seconds gains 3 mph each second, which is about 4.4 feet per second per second, or about 0.14 G. (FAA-H-8083-30B, ch. 5, p. 5-16)

Q.04

In principle you could find an airplane's CG by hanging it from a hook. How would that work, and why is it never done that way in the hangar?

Hang it from a point near the nose and drop a plumb line straight down from the hook, then hang it from a point near the tail and drop a second line. The 2 lines cross at the CG, the point where the nose-heavy and tail-heavy moments balance. In practice, slinging an airplane from the ceiling on 2 hooks is not realistic, and even if it could be done, it would be hard to tell where the lines meet inside the structure. So the airplane is set on at least 2 scales and the CG is worked out from the moments. (FAA-H-8083-30B, ch. 6, p. 6-5)

Q.05

On a bolted joint, why does it matter if a bolt is a loose fit in its hole, and where is a slight clearance acceptable?

A bolt in an oversized or elongated hole carries none of its shear load until the parts have yielded or deformed enough for the wall of the hole to bear against it. That is why bolt holes must not be oversized or elongated. A slight clearance is permissible wherever the bolt is loaded in tension and the load never reverses, for example in pulley brackets, conduit boxes, lining trim and miscellaneous supports and brackets. (FAA-H-8083-30B, ch. 7, p. 7-47)

Q.06

During a walkaround you find a little rust on several bolt heads and hold-down nuts in a wheel well. How serious is it, and what is it telling you?

On hardware like that it is usually not dangerous in itself and has no immediate effect on the strength of the major structure. But its residue can spread to other steel parts and start corrosion there. So it is a sign the airplane needs maintenance and that more critical areas may be under attack too, and it should be removed. Where paint has failed or damage has exposed a highly stressed steel part, even the smallest trace of rust is potentially dangerous and must be dealt with as soon as possible. (FAA-H-8083-30B, ch. 8, p. 8-15)

Q.07

You have to cut a length of small-diameter tubing with a hacksaw. How do you hold it for the cut, and why that way?

Slide the tube into a combination flaring tool, clamp the tool in a vise, and make the cut about 1/2 inch from the tool. Held that close to the cut, the tube barely vibrates while you saw, and it is protected if the hacksaw frame or the file handle knocks against it. (FAA-H-8083-30B, ch. 9, p. 9-2)

Q.08

You are about to bench-test a circuit board full of transistors with an ohmmeter and a signal generator. What precautions keep the test itself from damaging the parts?

Connect a ground between the test equipment and the board before you inject or monitor any signal. Keep every test voltage within what the components and transistors are rated to take. Do not test transistors on an ohmmeter range that drives more than 1 milliampere through the circuit. Where test points sit close together, keep as little of the probe tip exposed as you can so you cannot short across them. Take the power off before you change a part, and if one has to be soldered, use a low-wattage iron and a heat sink. (FAA-H-8083-30B, ch. 12, p. 12-5)

Q.09

Your shop quotes 8 weeks for a big inspection, and a competitor wins the customer by quoting 6 for the same work. If the competitor knows it really takes 8, what is it counting on?

That once the airplane is in its hangar and the work has begun, the owner is stuck. Few customers are able to pull an airplane out partway through maintenance, so the competitor can stretch the 6 weeks to 8 or more with explanations and excuses, and often adds extra costs as the work goes on. Shops like that rarely keep their customers for long, but there always seem to be new ones ready to take a shorter quote, so the trick keeps working for them. (FAA-H-8083-30B, ch. 13, p. 13-7)

Q.10

In April 2001 the left main gear of an Emery Worldwide DC-8 would not come down for landing. What did maintenance get wrong, and what does the case teach about the checks after a job?

It went wrong at 2 points. Maintenance installed the wrong hydraulic gear extension component, and inspection did not follow the post-maintenance test procedures, which is the step meant to catch that kind of error before the airplane flies. The lesson is that the test after the work is a defense in its own right: do it fully and by the book every time, because it may be the last chance to find a wrong part or a wrong installation while the airplane is still on the ground. (FAA-H-8083-30B, ch. 14, p. 14-32)

We wrote these cards for this page from the FAA handbooks. They are not FAA test questions and they are not what any examiner is bound to ask. Each answer names the handbook page it was written from, so you can check it.

02 AIRFRAME ORALAMA · 10 CARDS

FAA A&P Airframe oral practice questions

Written from FAA-H-8083-31B, across the Airframe subject areas. Every card ends with the handbook page its answer comes from.

Q.01

A ground handler dents a thin-skinned honeycomb panel, says nothing, and the airplane leaves on time. Why does a small dent like that, left unreported, matter?

Thin sandwich parts are stiff and strong but fragile in service: crawling over them or dropping a tool can crush the core or start a disbond. Damage left unchecked tends to grow, because liquids such as water or hydraulic fluid work into the core through it. By the time it is found the repair is bigger and harder: trapped water has to be dried out before a hot cure or it can disbond the skin, and core soaked with Skydrol usually has to be cut out. (FAA-H-8083-31B, ch. 7, p. 7-14)

Q.02

You are curving an angle strip by stretching one flange on a V-block. Why bring the whole strip roughly to the curve before finishing any one part of it?

Because finishing or smoothing one portion of the angle can change the shape of another portion. So form the curve gradually and evenly along the strip with light blows, check it often against a full-size pattern, and only then finish it. A part that ends up curved too much can be brought back by turning the strip over on the V-block and striking it lightly. Keep the hammering to a minimum, since too much of it work hardens the metal. (FAA-H-8083-31B, ch. 4, p. 4-74)

Q.03

A Zahn cup check shows a primer is too thick for your spray gun. Why must you stop thinning it at the coating maker's recommended limit, even if a thinner mix would spray more easily?

Thinning a coating below the manufacturer's recommendations can release volatile organic compounds into the air above the regulated limits. How easily it sprays is not the test. Adjust the viscosity only as far as the product's data sheet allows, and compare each new reading with the maker's recommendation before you add any more thinner. (FAA-H-8083-31B, ch. 8, p. 8-9)

Q.04

A hydraulic fluid has been run hot and exposed to air and water for a long time. What happens inside the system as the fluid breaks down chemically?

The fluid forms sludge, gums, carbon and other deposits. These clog small openings, make valves and pistons stick or leak, and leave moving parts poorly lubricated. Breakdown is worst when the fluid is exposed to air, water, salt or other impurities, especially while it is kept moving or heated. That is why chemical stability is one of the most important properties to weigh when a hydraulic fluid is chosen. (FAA-H-8083-31B, ch. 12, p. 12-2)

Q.05

You are choosing wire for a run that will sit behind panels and be inspected only rarely for years. Why should its heat-aging characteristics weigh heavily in the choice?

Nobody will see the wire for long periods, so its insulation has to stand up to heat over time without anyone checking on it. Resistance to heat is of primary importance in choosing aircraft wire and is the basic factor in its rating. Where a wire may run hot, from high ambient temperature, high current or both, choose it for satisfactory performance under the most severe operating conditions it will meet. (FAA-H-8083-31B, ch. 9, p. 9-67)

Q.06

You keep finding flat-spotted and skid-burned main tires on one operator's airplanes. Tire care is mostly in the pilots' hands, so why should you raise it with the flight crew?

Handling and care of tires is mostly the pilot's responsibility, so the technician helps most by knowing what causes tire failures and passing that on, so the crew can change the way they operate. Damage like this points to landing with the brakes on, landing long and braking hard, or skidding on a wet or icy runway, and a flat spot picked up on the way to the runway can lead to a failure on takeoff. Changing tires alone treats the result, not the cause. (FAA-H-8083-31B, ch. 13, p. 13-92)

Q.07

The fuel filler on a high-wing airplane is out of reach from the ground. Why should you fetch a ladder rather than climb up on the airplane to fuel it?

A ladder gives you a stable footing that climbing on the airplane does not, and an owner is unlikely to appreciate people clambering over an expensive aircraft to reach the filler. If walking on a wing really cannot be avoided, keep to the designated areas that are safe to walk on. Treat the fuel nozzle with the same care: keep its dust cap on until you fuel, and never drop it or drag it across the ramp. (FAA-H-8083-31B, ch. 14, p. 14-56)

Q.08

Deep, wet snow has been brushed and squeegeed off a parked airplane by hand. Why should someone look closely at its antennas, vents and other protrusions before it flies?

Snow can hide antennas, vents, stall warning devices, vortex generators and the like, so a brush or squeegee can strike and damage them without anyone noticing. Whenever snow has been removed by hand, every protrusion and vent is examined for signs of damage, and the drain and pressure sensing ports are checked for obstructions. A damaged stall warning device or a blocked sensing port is not something to find out about in the air. (FAA-H-8083-31B, ch. 15, p. 15-26)

Q.09

Light airplanes now mount most of their radios in the instrument panel. Why do most complex aircraft still keep an area away from the flight deck for their avionics?

Electronic bays began on older aircraft simply because the radios would not fit in the flight deck. Today many units are small enough for the panel, but a complex aircraft carries so many communication and navigation aids, and the pilot needs an uncluttered interface, so the boxes themselves go in a remote area and only their control heads stay on the flight deck. (FAA-H-8083-31B, ch. 11, p. 11-36)

Q.10

Air from a pressurization source comes out hot, because compressing air heats it. Why might a full air cycle system with an expansion turbine be chosen to cool it, instead of a heat exchanger alone?

A heat exchanger cools the air with cold ambient air, so it can only do its job when the outside air is cold enough. A full air cycle system also cools the air by making it drive an expansion turbine, which gives temperature control even on the ground and at low altitudes, where the outside air may be warmer than is comfortable for the passengers and crew. (FAA-H-8083-31B, ch. 16, p. 16-24)

We wrote these cards for this page from the FAA handbooks. They are not FAA test questions and they are not what any examiner is bound to ask. Each answer names the handbook page it was written from, so you can check it.

03 POWERPLANT ORALAMP · 10 CARDS

FAA A&P Powerplant oral practice questions

Written from FAA-H-8083-32B, across the Powerplant subject areas. Every card ends with the handbook page its answer comes from.

Q.01

On an unsupercharged radial at idle, a leaking intake pipe slip joint draws in outside air. Why does the same leak behave differently on a supercharged engine run at full throttle?

Because the pressure difference across the joint is turned round. On an unsupercharged engine the air outside the case is at a higher pressure than the inside, most of all at idling speed, so outside air is drawn in. On a supercharged engine at full throttle the pressure inside is considerably higher than outside, so the leak runs the other way and the charge is pushed out through the joint instead. Either way the slip joints, which let the cylinders lengthen and contract with heat, must be kept leak proof. (FAA-H-8083-32B, ch. 1, p. 1-6)

Q.02

Every ignition system leaks a little electrical energy. Why is that leakage worse on a harness that has been radio shielded?

Because the shielding is a metal conduit at ground potential, and it runs close to the ignition wires along their entire length. The high voltage has a ground right beside it all the way from the magneto to the plugs, so more of it escapes through the insulation, and the condition of that insulation matters all the more. A low-tension system cuts this leakage down a great deal, because most of it carries the current at a low voltage. (FAA-H-8083-32B, ch. 4, p. 4-11)

Q.03

A pilot keeps bringing back an engine that runs rough, and each time a fresh set of spark plugs cures it for a short while. What does that pattern tell you?

That the plugs are probably not the real problem. A carburetor fault, uneven fuel distribution, excess valve overlap, a leaky primer, or idle speed and mixture set badly can each look exactly like faulty ignition, and a plug change can make many of them better for a time. The trouble then comes back in a short time because its real cause was never removed. The fix is a proper look through the engine's systems, not another set of plugs. (FAA-H-8083-32B, ch. 4, p. 4-26)

Q.04

Cowl flaps and similar controls regulate the air flowing over an air-cooled engine. What could go wrong with the engine's temperature during a flight if it had no such controls?

It could overheat on takeoff, with the engine at high power, and then get too cold in a fast, low-power descent from high altitude. Without some control, cooling sized for one of those would be wrong for the other. Too cold matters as well as too hot: an engine is kept warm in flight for the same reasons it is warmed up before takeoff, so the aim is to hold it near its best operating temperature the whole way. (FAA-H-8083-32B, ch. 6, p. 6-33)

Q.05

A removed engine is stored in a sealed metal container charged with dehydrated air. Why is the container's air pressure rechecked from time to time, and what can change the reading even with no leak?

The occasional recheck of the air pressure is how a leak in the container is found, and a leak would let damp outside air in to undo the drying. The reading also moves with the weather, because radical changes in temperature change the air pressure inside the container. So a lower reading on a cold morning is not proof of a leak by itself; it has to be judged against the temperature. (FAA-H-8083-32B, ch. 8, p. 8-21)

Q.06

A continuous-loop control unit can send a fault signal when its short discriminator finds a short in the sensing loop. Is that fault indication required on every airplane?

No. 14 CFR requires it on transport category aircraft, because a short in the sensing element disables the fire detection system, and the crew has to know that the zone is no longer being watched. On other aircraft types it is offered as an option, since there it may not be a requirement. So whether a given airplane has it depends on how it was certificated and equipped. (FAA-H-8083-32B, ch. 9, p. 9-6)

Q.07

You find a nick on a hollow compressor guide vane of a turbine engine. Why can't it be blended out as freely as damage on a solid part?

A hollow vane is built from thin sheet, so there is very little metal to take away. For that reason blending on its concave and convex surfaces, including the leading edge, is limited. Small, shallow dents with a rounded contour can be left where there is no cracking or tearing, and damage at the trailing edge may be blended only while at least one-third of the weld seam remains. The manufacturer's current limits decide each case. (FAA-H-8083-32B, ch. 10, p. 10-47)

Q.08

You are taking the pushrods out of a lower cylinder during cylinder removal. What could drop out as the pushrod and its housing come away, and what should you do about it?

On some engines, or if the engine has been turned, the tappets and their springs in the lower cylinders can fall out as the pushrod and housing are removed. Be ready to catch them, so they are not lost or damaged and nothing ends up where it should not be. Then keep each pushrod marked for the place it came from, so it goes back into the same location. (FAA-H-8083-32B, ch. 10, p. 10-41)

Q.09

The aluminum billet that Jabiru cylinder heads are machined from is bought directly from one company. Why does it matter that the metal comes from a single source?

Buying the billet straight from one company gives a substantive quality control trail back to the material source, so the maker can trace what metal went into the heads. It fits the way the whole engine is built: the crankcase halves, heads, crankshaft and many smaller parts are machined from solid material, the oil sump is the only casting, and every engine is run on a dynamometer and calibrated before delivery. (FAA-H-8083-32B, ch. 11, p. 11-10)

Q.10

A one-piece aluminum fixed-pitch propeller has no joint between its blades and its hub. How can its pitch still be changed?

Because there is no joint, the blade itself is twisted slightly to change the pitch, and only within limits. It is work for a propeller repair station, not something done on the line. A propeller with separate blades sets a new angle the other way, by turning each blade in the hub, which is exactly the joint this design does without. (FAA-H-8083-32B, ch. 7, p. 7-13)

We wrote these cards for this page from the FAA handbooks. They are not FAA test questions and they are not what any examiner is bound to ask. Each answer names the handbook page it was written from, so you can check it.

04 HOW TO USE THEM§ 65.79

How to practice for the FAA A&P oral

Answer out loud, in full sentences, the way you would to an examiner across a bench, and only then open the card. A spoken answer that trails off is the one to practice again. Keep each answer short and complete: what it is, why it matters, and where you would look it up.

How long your oral runs is set by your written score. A clean written gets you 4 questions per section; scrape the 70% and every ACS code printed on your test report adds 1 more, up to 22 for General and 34 each for Airframe and Powerplant. There are 6 tests in the oral and practical in all, an oral and a practical for each section.

The whole process, from the test planning sheet to retests, is on the oral and practical page.

FREE PLAN · NO CARD · 25 QUESTIONS TO START

Practice the written that sets how long your oral runs.

Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.

Start free

Or answer a few first. The free FAA A&P practice test runs on the page, with no account.