PrepAMT Academy

AMG · PRACTICE QUESTIONS · WRITTEN FOR THIS PAGE

Free FAA A&P General practice questions

15 practice questions for the FAA A&P General written test (AMG), in its own format: 3 options and 1 correct answer. Each names the FAA handbook page it was written from, and its answer and reason are one tap away. The test itself is 60 questions in 2 hours, 70% to pass, and the FAA A&P General written test page has everything else about it.

Questions written from FAA-H-8083-30B to FAA-S-ACS-1, the current Airman Certification Standards.

01 THE QUESTIONSAMG · 15 QUESTIONS

FAA A&P General practice questions and answers

They come from 11 of the General test’s subjects, no more than 2 from any one. Pick your answer, then open each question to see the right one and the reason.

  1. Q.01

    Most metals used as conductors gain resistance as they warm up. Which of these materials does the opposite, losing resistance as its temperature rises?

    FAA-H-8083-30B, ch. 12, p. 12-19

    1. ACopper
    2. BConstantan
    3. CCarbon
    SHOW THE ANSWER

    THE ANSWER IS C.

    Carbon

    Copper behaves like most conductor metals: its resistance goes up as it gets warmer. Alloys such as constantan and Manganin are made so their resistance hardly changes with temperature, which is why they suit precision resistors. Carbon is one of the few substances that goes the other way, its resistance falling as the temperature around it rises.

  2. Q.02

    An airplane already carries 2 modifications made under supplemental type certificates (STCs), and its owner now wants a third STC installed. Going by the conditions an STC carries, who has to determine that the new change is compatible with the 2 already there?

    FAA-H-8083-30B, ch. 2, p. 2-32

    1. AThe installer doing the new modification, before it goes in
    2. BThe FAA, which checked it against other STCs when it was issued
    3. CThe holder of the new STC, whose approval covers every airplane of that model
    SHOW THE ANSWER

    THE ANSWER IS A.

    The installer doing the new modification, before it goes in

    An STC approves a change to a product's type design, and the limitations and conditions printed on it go with the change. One of them puts this question on the installer, who must determine whether the design change is compatible with previously approved modifications. The FAA and the STC holder approved the change for the model, not for every mix of other STCs one airplane might carry, so it is settled airplane by airplane by whoever installs it.

  3. Q.03

    A helicopter is weighed on 3 jacks standing on electronic floor scales. The scales were zeroed with the jacks already standing on them, before the helicopter was raised. How is the weight of the jacks handled when the readings are worked up?

    FAA-H-8083-30B, ch. 6, p. 6-29

    1. AEach jack's weight is subtracted from its scale reading as tare
    2. BNothing is taken off, since the readings are the helicopter's alone
    3. CThe scales are zeroed once more after the helicopter is up on the jacks
    SHOW THE ANSWER

    THE ANSWER IS B.

    Nothing is taken off, since the readings are the helicopter's alone

    Normally the weight of jacks, chocks or other equipment resting on the scales is subtracted from the readings as tare. Here the scales were zeroed while the jacks were already standing on them, so their weight never appears in the readings and no tare has to be accounted for. Taking the jacks off a second time would make the helicopter come out light, and zeroing again with the helicopter raised would wipe out the very weight being measured.

  4. Q.04

    You are checking a plate with straight-beam pulse-echo ultrasonics. On the screen, what does the horizontal distance between the initial pulse and the first back reflection show?

    FAA-H-8083-30B, ch. 10, p. 10-23

    1. AThe distance from the probe to the nearest edge of the plate
    2. BThe thickness of the plate under the probe
    3. CThe depth of the deepest flaw anywhere in the plate
    SHOW THE ANSWER

    THE ANSWER IS B.

    The thickness of the plate under the probe

    In straight-beam testing the sound goes straight in, reflects from the far surface and returns, so the horizontal distance between the initial pulse and the first back reflection represents the thickness of the piece. A flaw shows as its own echo in between. In angle-beam testing that distance means something else: the width of material between the search unit and the opposite edge of the piece.

  5. Q.05

    A shop's most senior inspector, in his sixties, has started missing fine details in a poorly lit corner of the hangar. Under the People element of PEAR, what does this point to?

    FAA-H-8083-30B, ch. 14, p. 14-9

    1. AProper lighting for the task, which matters most of all for older workers
    2. BLonger breaks, since fatigue is the usual reason for missed details at his age
    3. CMoving him off inspection work, since the job has to fit the average worker
    SHOW THE ANSWER

    THE ANSWER IS A.

    Proper lighting for the task, which matters most of all for older workers

    A human factors program fits the job to the people doing it, with their size, strength, age and eyesight in mind. One People consideration, which also falls under Environment, is proper lighting for the task, especially for older workers, along with annual vision and hearing checks. Better light is the first thing to fix here, and the program is built to help people do the work, not to sideline them.

  6. Q.06

    Some helicopters carry a small fixed horizontal stabilizer near the tail, much like the one on an airplane. What is it there to provide?

    FAA-H-8083-30B, ch. 5, p. 5-54

    1. AAnti-torque force that takes some load off the tail rotor
    2. BLift that lets the main rotor carry a heavier load
    3. CAdded stability about the lateral axis, in pitch
    SHOW THE ANSWER

    THE ANSWER IS C.

    Added stability about the lateral axis, in pitch

    Like the one on an airplane, a helicopter's horizontal stabilizer is there to add stability about the lateral axis, which steadies the nose in pitch. The surface that helps with torque is the vertical stabilizer: in forward flight it makes a force that counters main-rotor torque and cuts the power the tail rotor needs. The lift that carries the helicopter comes from the main rotor, not from a small tail surface.

  7. Q.07

    You are bolting together 2 fittings with a total thickness of 7/16 inch. The only bolt of the right diameter on hand has a grip length of 1/2 inch. How can it be used?

    FAA-H-8083-30B, ch. 7, p. 7-48

    1. AAs it is, since a slightly longer grip only leaves extra shank under the nut
    2. BWith a washer under the nut or the head to take up the extra grip
    3. CNot at all, since an aircraft bolt's grip must match the stack exactly
    SHOW THE ANSWER

    THE ANSWER IS B.

    With a washer under the nut or the head to take up the extra grip

    Grip length is the unthreaded part of the shank, and it should equal the thickness of the material being bolted. A bolt with a slightly longer grip may still be used if washers go under the nut or the bolt head. Without them, the nut runs out of thread before it can clamp the fittings, so the joint is never drawn tight. The rule allows the longer grip with washers, so an exact match is not the only choice.

  8. Q.08

    Piano-type hinges are named among the prime spots for corrosion on an airframe. What makes them so prone to it?

    FAA-H-8083-30B, ch. 8, p. 8-13

    1. AA steel pin runs through an aluminum hinge, and the hinge traps dirt, salt and moisture
    2. BThe hinge leaves flex at every cycle, cracking the paint along each knuckle
    3. CTheir pins are made of magnesium, the most active metal used on an airframe
    SHOW THE ANSWER

    THE ANSWER IS A.

    A steel pin runs through an aluminum hinge, and the hinge traps dirt, salt and moisture

    Where a steel pin runs through an aluminum hinge, 2 dissimilar metals are in contact, and the hinge is also a natural trap for dirt, salt and moisture, so everything corrosion needs is right there. That is why the inspection includes a water-displacing lubricant and working the hinge through several cycles. The leaves turn on the pin rather than bend, and the pin is steel, not magnesium.

  9. Q.09

    After fitting a new hydraulic hose, you notice that the identification stripe printed along it spirals about half a turn between the 2 end fittings. Why must that be put right before the system is pressurized?

    FAA-H-8083-30B, ch. 9, p. 9-21

    1. AHigh pressure on a twisted hose can burst it or loosen its end nuts
    2. BA twisted hose chokes the flow through it much as a kink would
    3. CThe printing has to run straight so the hose data can be read
    SHOW THE ANSWER

    THE ANSWER IS A.

    High pressure on a twisted hose can burst it or loosen its end nuts

    A stripe that spirals means the hose went in twisted, and hoses must be installed without twist. Under high pressure a twisted hose can rupture or work its attaching nuts loose, so the twist is taken out before the system is pressurized, and swivel connections at one or both ends help relieve it. The danger of twist is that failure or loosening, not a restricted flow, and the stripe runs straight to show twist, not to make the markings easier to read.

  10. Q.10

    Inspecting an aircraft generator, you find a slight grooving across the faces of its brushes. The maintenance data shows they are a special type, with 2 cores of a harder material set into the brush body. What should you do about the grooves?

    FAA-H-8083-30B, ch. 12, p. 12-137

    1. AReplace the brushes, since grooved faces mean they no longer make good contact
    2. BLeave them in service, since that grooving is normal for those brushes
    3. CTurn and polish the commutator, since grooved brushes mean it is worn
    SHOW THE ANSWER

    THE ANSWER IS B.

    Leave them in service, since that grooving is normal for those brushes

    Some special generator brushes show a slight grooving on the face in normal service and are not replaced because of it. They have 2 cores of a harder material that expands more than the main body: the body normally rides on the commutator, but at certain temperatures the cores extend and wear through any film on it. A brush is replaced when it has worn to the minimum length the manufacturer allows, not because of that grooving.

  11. Q.11

    Which organization is the only one in the United States dedicated specifically to the human factors profession?

    FAA-H-8083-30B, ch. 14, p. 14-31

    1. AThe International Ergonomics Association
    2. BThe FAA Safety Team
    3. CThe Human Factors and Ergonomics Society
    SHOW THE ANSWER

    THE ANSWER IS C.

    The Human Factors and Ergonomics Society

    The Human Factors and Ergonomics Society, formed in 1957, is the single U.S. body given over entirely to the human factors profession. The International Ergonomics Association is a worldwide federation of such societies, and the FAA Safety Team runs an FAA website of safety information, seminars and courses.

  12. Q.12

    You are quenching a heat-treated steel bracket in a tank of oil. A helper suggests just dropping it in and letting it sit on the bottom. What is wrong with that?

    FAA-H-8083-30B, ch. 7, p. 7-16

    1. ALying on the bottom, its top cools faster than its underside, so it can warp or crack
    2. BDropping it splashes oil about, but the bracket itself is not affected
    3. CNothing, since oil cools so gently that steel cannot warp in it
    SHOW THE ANSWER

    THE ANSWER IS A.

    Lying on the bottom, its top cools faster than its underside, so it can warp or crack

    A part thrown into the quench and left on the bottom of the tank cools faster on its top side than on the side lying against the bottom, and that uneven cooling makes it warp or crack. It should be lowered in and agitated slightly, which breaks up the vapor coating so it cools evenly. Splashing is a hazard of its own, but the real harm is to the part, and oil, the slowest of the usual quenching liquids, still lets steel warp when one side cools first.

  13. Q.13

    A stitch line and a hidden line are both drawn as a row of short dashes. What tells you that a line on a print is a stitch line?

    FAA-H-8083-30B, ch. 4, p. 4-18

    1. AIts dashes are drawn heavier than the part's outline
    2. BIts dashes come in pairs, with a wider gap after each
    3. CIts dashes are about half as long as a hidden line's dashes
    SHOW THE ANSWER

    THE ANSWER IS C.

    Its dashes are about half as long as a hidden line's dashes

    Hidden lines, often called dash lines, show edges that cannot be seen in the view. Stitch lines show the stitching or sewing on an article, and their dashes are very short, about half the length of hidden-line dashes, and evenly spaced rather than grouped. Line weight is not what sets a stitch line apart. A long run of stitching may be shown as stitch lines joined by phantom lines.

  14. Q.14

    You have finished a hacksaw cut and are about to hang the saw back in its place on the tool board. What should you do to it first?

    FAA-H-8083-30B, ch. 11, p. 11-9

    1. ATighten the blade a little more so it is ready for the next cut
    2. BOil the blade and leave it at full tension so it keeps its set
    3. CClear the chips from the blade and loosen the blade tension
    SHOW THE ANSWER

    THE ANSWER IS C.

    Clear the chips from the blade and loosen the blade tension

    When the cut is done, remove the chips from the blade, loosen the tension on the blade, and put the hacksaw back where it belongs. Leaving a blade under tension, or tightening it further, only strains the blade and frame while the saw hangs unused. Cutting pressure goes on the forward stroke, at no more than 40 to 50 long, steady strokes a minute.

  15. Q.15

    A cabin is being cleaned with flammable agents while the airplane sits outside the hangar, with portable extinguishers at the cabin entrances. What else must be on hand until airport fire equipment arrives?

    FAA-H-8083-30B, ch. 8, p. 8-26

    1. AA foam truck with its crew parked and waiting within 50 feet of the airplane
    2. BA booster hose with an adjustable water spray nozzle that reaches the cabin
    3. CA fixed carbon dioxide flooding system installed inside the cabin itself
    SHOW THE ANSWER

    THE ANSWER IS B.

    A booster hose with an adjustable water spray nozzle that reaches the cabin

    When a cabin is cleaned or refurbished with flammable agents outside the hangar, portable extinguishers go at the cabin entrances, and at minimum a booster hose line with an adjustable water spray nozzle able to reach the cabin must be available, for use until airport fire equipment arrives. A foam truck on standby or a fixed flooding system in the cabin is not what is called for.

We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.

03 COMMON QUESTIONSFAQ

About these practice questions

Q.01

Are these real FAA A&P General test questions?

No. We wrote them for this page from FAA-H-8083-30B, the FAA’s General handbook, and each one names the page it was written from so you can check it. They are not FAA test questions, and none of them comes from our question bank.

Q.02

How should I use these FAA A&P General practice questions?

Answer each one before you open it, and note the ones you miss. A miss points at a subject, and each subject has its own page below, with more questions on it and how much of the General test it is.

Q.03

How many questions are on the FAA A&P General test?

60, in 2 hours, with 70% to pass. Everything else about the test is on the FAA A&P General written test page.

Q.04

Where can I practice more FAA A&P General questions?

Our bank holds 4,071 General questions across 14 subjects, each with a written explanation. A free account gives you one free set, 25 questions and 25 fill-in-the-gaps from any subject you pick, once, and Pro opens the rest.

FREE PLAN · NO CARD · 25 QUESTIONS TO START

The bank holds 4,071 FAA A&P General questions.

Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.

Start free

Or answer a few first. The free FAA A&P practice test runs on the page, with no account.