PrepAMT Academy

AMG · GEN-04 · FAA-H-8083-30B CH. 4

FAA A&P General: Aircraft Drawings

For the FAA A&P General test, aircraft drawings and blueprints is chapter 4 of FAA-H-8083-30B, Aircraft Drawings. Its ACS subject area, Aircraft Drawings, is 5 to 10% of the test, or 3 to 6 of its 60 scored questions. Our question bank holds 229 questions on it, and the 10 below were written for this page.

Test shares and most-missed codes read from the FAA on 15 November 2026.

01 WHAT IT COVERSFAA-H-8083-30B · CH. 4

What FAA-H-8083-30B chapter 4 covers

Chapter 4 is how to read the drawings a part or a repair is made from. It covers the purpose of drawings and how to care for them; the types, from detail, assembly and installation drawings to sectional and exploded views and block and schematic diagrams; title blocks and drawing numbers; revisions; the bill of material; and the dimensions and tolerances a drawing carries.

It then explains the methods of illustration, including orthographic and pictorial views, the meaning of each kind of line, the symbols for materials and electrical parts, how to sketch, and how to read graphs, charts and nomograms. It closes with microfilm, microfiche and digital images.

It runs from pages 4-1 to 4-26 of the Aviation Maintenance Technician Handbook: General, which the FAA publishes free as a PDF.

02 SHARE OF THE TESTFAA-G-ACS-1 · BLUEPRINT

How much of the FAA A&P General test it is

  • 5 to 10%OF THE TESTACS area AM.I.B
  • 3 to 6QUESTIONSof 60 scored
  • 229IN OUR BANKquestions on this subject

The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Aircraft Drawings (AM.I.B) is 5 to 10% (3 to 6 questions) on the 60-question General test. The 12 ranges for the General test add up to anywhere from 60% to 130%, so they say how big an area can get, not how many questions you will see from it.

No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.

03 EXAMPLE QUESTIONSWRITTEN FOR THIS PAGE

Aircraft drawings and blueprints questions and answers

10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.

  1. Q.01

    A drawing of a long control tube shows a gap partway along it, closed off at each side by ruled zigzag lines, and the overall dimension reads 48.00 inches. How long is the tube?

    FAA-H-8083-30B, ch. 4, p. 4-18

    1. A48.00 inches less the length of the piece left out of the view
    2. BWhatever the drawn length scales out to at the print's stated scale
    3. C48.00 inches, since the break only leaves part of the length undrawn
    SHOW THE ANSWER

    THE ANSWER IS C.

    48.00 inches, since the break only leaves part of the length undrawn

    Break lines show that a portion of the object is not drawn, usually so a long, uniform part such as a tube or shaft fits on the sheet. Ruled lines with zigzags mark a long break and freehand lines a short one. The dimension still gives the part's real length, so the tube is 48.00 inches. Nothing comes off for the gap, and a size is taken from the dimension, never by scaling the print.

  2. Q.02

    An assembly drawing of a clamp bracket also shows the hydraulic tube the clamp will hold, outlined in lines of one long dash and 2 short dashes. The tube is not part of this assembly. Why is it drawn that way?

    FAA-H-8083-30B, ch. 4, p. 4-17

    1. ATo show that it must be fitted before the bracket goes on
    2. BTo show where it will sit in relation to the bracket
    3. CTo show that it is to be taken off and replaced in this job
    SHOW THE ANSWER

    THE ANSWER IS B.

    To show where it will sit in relation to the bracket

    Lines of one long dash and 2 short dashes, evenly spaced, are phantom lines. They show either an alternate position of part of the object or the relative position of a missing part, and the tube here is a missing part: it is outlined only so you can see where it will sit in relation to the bracket. Phantom lines say nothing about the order in which parts go on, or about taking a part off.

  3. Q.03

    Reading a multiview print in order, you have checked that it is the right drawing and worked out the shape of the part from its views. What should you work out next?

    FAA-H-8083-30B, ch. 4, p. 4-20

    1. AThe size of the part and its tolerances
    2. BThe general notes and the content of the material block
    3. CThe model affected and the latest change letter
    SHOW THE ANSWER

    THE ANSWER IS A.

    The size of the part and its tolerances

    A drawing is read in a set order. First come the number and description, then the model affected, the latest change letter and the next assembly, which show it is the right drawing. Next you scan the views to work out the shape, and once you have the shape you determine the size from the dimensions and tolerances given. The general notes, the material block, the changes and any special information are read last, to complete the reading.

  4. Q.04

    A note sends you to zone C4 of a large assembly drawing. How do you find that area on the sheet?

    FAA-H-8083-30B, ch. 4, p. 4-8

    1. ATurn to sheet 4 of the drawing set and look for the view labeled C
    2. BLook up C4 in the bill of material to read off its location
    3. CFollow the C and the 4 in from the borders to where they cross
    SHOW THE ANSWER

    THE ANSWER IS C.

    Follow the C and the 4 in from the borders to where they cross

    Zone numbers work like the grid printed around a road map. Find the letter and the number on the borders of the drawing, run imaginary lines in from each, and the area you want is where they cross. It is the usual way to find parts, sections and views on large assembly drawings.

  5. Q.05

    A designer models a new bracket and the existing duct it must clear as separate parts in CAD software, then puts them together on the screen. What is that step checking?

    FAA-H-8083-30B, ch. 4, p. 4-1

    1. AThat the parts fit together and do not interfere with one another
    2. BThat every part will last its full service life without wearing
    3. CThat none of the drawings will need changing once production starts
    SHOW THE ANSWER

    THE ANSWER IS A.

    That the parts fit together and do not interfere with one another

    Computer design software lets parts that were created separately be assembled on screen to check for proper fit and possible interference before anything is made, and most airframe makers design and assemble the complete aircraft in the software before it is built. A fit check on screen tells you nothing about how long a part will last in service, and drawings are still revised whenever the dimensions, design or materials change.

  6. Q.06

    On the front view of a fitting, a heavy line with arrowheads at its ends is lettered A at each end. Where do you look to see the part's shape along that line?

    FAA-H-8083-30B, ch. 4, p. 4-19

    1. AThe outline drawn in phantom lines showing its other position
    2. BA sectional view labeled A-A, taken at the plane that line marks
    3. CThe entry for item A in the bill of material for the fitting
    SHOW THE ANSWER

    THE ANSWER IS B.

    A sectional view labeled A-A, taken at the plane that line marks

    A heavy line with arrowheads cutting across a view is a cutting plane line. It marks the plane where a sectional view is taken, and its letters name that view, so line A leads you to section A-A. Phantom lines, one long dash and 2 short ones, show an alternate position, not a cut, and a bill of material lists parts by item number, not by section letter.

  7. Q.07

    A service manual shows a bracket in an isometric view, with dimensions along its edges. How do those edges compare with the same bracket in an orthographic projection?

    FAA-H-8083-30B, ch. 4, p. 4-11

    1. AThey are parallel and dimensioned the same way as in the orthographic view
    2. BThey run toward a vanishing point, so the sizes are only approximate
    3. COnly the front face is true, and the edges going back are drawn half length
    SHOW THE ANSWER

    THE ANSWER IS A.

    They are parallel and dimensioned the same way as in the orthographic view

    An isometric view tilts the object so parts of all 3 views show at once, but its lines stay parallel and are dimensioned as they are in an orthographic projection, so the sizes on it are true. Lines that run toward a vanishing point belong to a perspective drawing, where sizes and angles are not accurate. Nothing in an isometric view is drawn at half length.

  8. Q.08

    The top view of a fitting shows a circle. In the front view, 2 dashed lines run straight down from the top surface to the bottom surface at the edges of that circle. What is the circle?

    FAA-H-8083-30B, ch. 4, p. 4-19

    1. AA boss that stands up from the top surface of the fitting
    2. BA hole that runs right through the fitting from top to bottom
    3. CA shallow recess that stops partway down from the top surface
    SHOW THE ANSWER

    THE ANSWER IS B.

    A hole that runs right through the fitting from top to bottom

    A circle on one view can be a hole or a boss standing up from the surface, so you read the adjacent view to tell which. Here the front view shows the edges of the circle as hidden lines, which mark edges you cannot see, running the full depth of the part. That makes it a hole right through. A boss would show as visible outline above the top surface, and a recess would end partway down.

  9. Q.09

    A skin panel runs from fuselage station 222.0 aft to fuselage station 350.2. A stiffener is to go across it at the panel's midpoint. At what fuselage station does the stiffener go?

    FAA-H-8083-30B, ch. 4, p. 4-8

    1. AFS 64.1
    2. BFS 175.1
    3. CFS 286.1
    SHOW THE ANSWER

    THE ANSWER IS C.

    FS 286.1

    Fuselage stations are distances in inches from the datum, so the panel is 350.2 less 222.0, or 128.2 inches long. Half of that is 64.1 inches, and the midpoint is 64.1 inches aft of the panel's forward edge: 222.0 plus 64.1 is FS 286.1. 64.1 is a distance, not a station, and 175.1 is half of 350.2, which forgets that the panel starts at 222.0.

  10. Q.10

    An antenna doubler on the belly runs from left buttock line 12.5 to right buttock line 8. How wide is the doubler?

    FAA-H-8083-30B, ch. 4, p. 4-9

    1. A4.5 inches
    2. B10.25 inches
    3. C20.5 inches
    SHOW THE ANSWER

    THE ANSWER IS C.

    20.5 inches

    Buttock lines are measured left and right from the aircraft's centerline, which is the zero line. A part that crosses the centerline spans its left distance plus its right distance: 12.5 plus 8 is 20.5 inches. Subtracting the 2 figures gives 4.5, which would only be right if both lines were on the same side.

We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.

04 AND THEN THE ORAL§ 65.79

How a missed code comes back at the oral

Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.I.B. The examiner reads those codes before your oral and practical.

The General oral runs from 4 questions if your written was clean up to 22, because every code you missed adds 1 more. General also carries 9 practical projects, each with 2 questions attached.

Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.

05 COMMON QUESTIONSFAQ

Questions people ask about aircraft drawings and blueprints

Q.01

What does a hidden line look like on an aircraft drawing?

A line of short, evenly spaced dashes. It shows an edge or surface that cannot be seen in that view because something is in front of it. A center line is different: it alternates long and short dashes and marks the center of a hole or a symmetrical part.

Q.02

What is an orthographic projection?

A way of drawing an object in views taken straight on to each of its faces, so every face shows at its true shape. There can be up to 6 views, but a drawing shows only the ones it needs. Drawings with 1, 2 or 3 views are the most common, with the front view as the main one.

Q.03

What is the title block on a drawing for?

It identifies the drawing: its number, the name of the part or assembly, the scale, the date, the company, and the people who drew, checked and approved it. The drawing number is what you use to find the right drawing and the right part.

Q.04

What is tolerance on a drawing?

The amount a dimension is allowed to vary from the size the drawing gives. A part dimensioned 1.250 inches, plus or minus 0.005, is acceptable anywhere from 1.245 to 1.255 inches. Anything outside that is out of tolerance, however close it looks.

Q.05

How many aircraft drawings and blueprints questions are on the FAA A&P General test?

The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Aircraft Drawings subject area 5 to 10% of the General test, which is 3 to 6 of the 60 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.

Q.06

Which FAA handbook chapter covers aircraft drawings and blueprints?

Chapter 4 of FAA-H-8083-30B, the Aviation Maintenance Technician Handbook: General, titled "Aircraft Drawings". It runs from pages 4-1 to 4-26, and the FAA publishes the whole handbook free as a PDF.

FREE PLAN · NO CARD · 25 QUESTIONS TO START

The bank holds 229 aircraft drawings and blueprints questions.

Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.

Start free

Or answer a few first. The free FAA A&P practice test runs on the page, with no account.