AMG · GEN-05 · FAA-H-8083-30B CH. 5
FAA A&P General: Physics for Aviation
For the FAA A&P General test, physics for aviation is chapter 5 of FAA-H-8083-30B, Physics for Aviation. Its ACS subject area, Physics for Aviation, is 5 to 10% of the test, or 3 to 6 of its 60 scored questions. Our question bank holds 377 questions on it, and the 10 below were written for this page.
Test shares and most-missed codes read from the FAA on 15 November 2026.
What FAA-H-8083-30B chapter 5 covers
Chapter 5 covers matter and energy; force, work, power and torque; the simple machines, levers, pulleys, gears and the inclined plane; stress; and motion, with Newton’s laws of motion and the difference between speed, velocity and acceleration.
It then covers heat and how it travels, pressure and the ways it is measured, the gas laws, fluid mechanics with Pascal’s and Bernoulli’s principles, sound, and the atmosphere. The last part is the theory of flight for airplanes and helicopters: lift and drag, the axes of flight, stability and control.
It runs from pages 5-1 to 5-62 of the Aviation Maintenance Technician Handbook: General, which the FAA publishes free as a PDF.
How much of the FAA A&P General test it is
- 5 to 10%OF THE TESTACS area AM.I.J
- 3 to 6QUESTIONSof 60 scored
- 377IN OUR BANKquestions on this subject
The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Physics for Aviation (AM.I.J) is 5 to 10% (3 to 6 questions) on the 60-question General test. The 12 ranges for the General test add up to anywhere from 60% to 130%, so they say how big an area can get, not how many questions you will see from it.
No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.
Physics for aviation questions and answers
10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.
- Q.01
During an eclipse of the sun, the warmth of the sunshine is cut off at the same moment as its light. What does that show about heat that travels by radiation?
FAA-H-8083-30B, ch. 5, p. 5-21
- AIt travels at the speed of light, much faster than conduction or convection
- BIt travels by convection, so the air cools as soon as the sun is covered
- CIt travels by conduction through the air, which stops when the light does
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
It travels at the speed of light, much faster than conduction or convection
Conduction and convection move heat slowly, but radiation travels at the speed of light. That is why, during an eclipse, the heat from the sun is shut off at the same moment as its light. The sun's heat reaches us by radiation across empty space, not by air currents or by contact through the air, so neither of those could stop in step with the light.
- Q.02
Gliders are built with very long, narrow wings, which gives them a high aspect ratio. What does that wing shape do for them?
FAA-H-8083-30B, ch. 5, p. 5-39
- AIt adds drag at a given speed, accepted in return for extra lift
- BIt gives less drag at a given flight speed than a short, broad wing
- CIt suits them to flight above the speed of sound, as a delta wing does
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
It gives less drag at a given flight speed than a short, broad wing
Aspect ratio compares a wing's span, from tip to tip, with its chord. A long span with a very narrow chord is a high aspect ratio, and a higher aspect ratio produces less drag for a given flight speed, which is why it is typically found on gliders. It lowers drag rather than adding it, and for supersonic flight a delta shape might be used, not a long, narrow wing.
- Q.03
Heat is passing by conduction alone, with nothing flowing. Which of these carries it the most poorly?
FAA-H-8083-30B, ch. 5, p. 5-19
- AAn aluminum bracket
- BEngine oil in a line
- CA layer of still air
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
A layer of still air
Conduction passes heat along by contact, molecule to molecule. Metals such as aluminum and copper do it well, liquids more poorly, and gases poorest of all, which is why you can stand close to a stove without being burned. So of these 3 the layer of still air is the poorest conductor, the oil carries heat better than the air, and the aluminum bracket carries it best.
- Q.04
Replacing an engine's oil pressure gauge, you find a gauge on the shelf that reads absolute pressure, in psia. Why is that kind of gauge not used for oil pressure?
FAA-H-8083-30B, ch. 5, p. 5-23
- AStopped, it would still read atmospheric pressure, which misleads the operator
- BAn absolute gauge tops out below the pressure an oil pump makes
- CAbsolute gauges read in inches of mercury, so it would not show psi
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Stopped, it would still read atmospheric pressure, which misleads the operator
Oil, fuel and hydraulic gauges read gauge pressure, the pressure over and above the air around them, so they show zero when the pump is not turning. An absolute gauge adds atmospheric pressure, so on a stopped engine it would still show about 14.7 psi, which makes no sense to the person reading it. Absolute gauges can read in psi and to high values; manifold pressure is where an absolute reading does make sense.
- Q.05
A mechanic pulls a 1,200-pound tool cart 150 feet across a level hangar floor. What sets the force to use when working out the work he does?
FAA-H-8083-30B, ch. 5, p. 5-4
- AThe force needed to overcome the cart's rolling friction
- BThe cart's full 1,200-pound weight, multiplied by the 150 feet
- CThe cart's weight shared between its 4 wheels, times the distance
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
The force needed to overcome the cart's rolling friction
Work is the resistance actually overcome times the distance moved, and that is not always the weight of the thing being moved. On a level floor the mechanic is not lifting the cart, only working against its rolling friction, which may be a small part of its weight. Using the full weight would be right only for lifting the load straight up, and sharing the weight between the wheels has nothing to do with it.
- Q.06
A steel part that spent the night in an unheated hangar is carried into a warm, humid shop, and within a minute it is covered in fine water droplets. What explains that?
FAA-H-8083-30B, ch. 5, p. 5-36
- AThe steel is giving off moisture it soaked up while it sat in the cold
- BAir touching the cold part is cooled below its dew point, so vapor condenses
- CThe warm shop air is over 100 percent humid, so water falls out everywhere
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Air touching the cold part is cooled below its dew point, so vapor condenses
Dew point is the temperature humid air must be cooled to, at constant pressure, before it is saturated, and below it condensation occurs. The air in contact with the cold part is cooled below the shop air's dew point, so some of its water vapor condenses on the metal, the same thing that fogs cold eyeglasses in a warm room. The water comes out of the air, not out of the steel, and the rest of the shop air stays clear because it is not being cooled.
- Q.07
A lead bar and an aluminum bar of the same length sit side by side at the same temperature. You tap one end of each and time the sound to the other end. Which one does it cross first?
FAA-H-8083-30B, ch. 5, p. 5-31
- AThe lead bar, since lead is much denser and sound travels faster in denser material
- BThey tie, since both are metal bars of the same length at the same temperature
- CThe aluminum bar, since sound speed depends on elasticity as well as density
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
The aluminum bar, since sound speed depends on elasticity as well as density
As a rule of thumb, sound travels faster through the denser of 2 substances, which is why it goes faster through water than through air. Lead and aluminum are one of the exceptions: at 20 °C sound crosses aluminum at about 16,700 feet per second and lead at only about 4,030, although lead is much denser. The speed depends on how elastic the material is as well as how dense, so density alone gets this one wrong, and different metals do not share one speed.
- Q.08
A retractable main gear leg pivots at its top, carries the wheel and brake at its bottom, and has its retraction actuator attached partway down. Treating the leg as a simple lever, how does the actuator's force compare with the load at the wheel?
FAA-H-8083-30B, ch. 5, p. 5-9
- AIt is less than the load, since the leg works as a lever that multiplies the actuator's push
- BIt equals the load, since the actuator and the wheel sit on the same leg
- CIt is more than the load, since it pushes closer to the pivot than the wheel
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
It is more than the load, since it pushes closer to the pivot than the wheel
With the pivot at one end, the load at the other and the effort applied between them, the gear leg is a third class lever. Effort times effort arm equals load times load arm, and the actuator's arm is the shorter one, so it has to push harder than the load it moves. What the design buys is speed and travel at the wheel. A lever gains force only when the effort arm is the longer one, and sharing a leg does not make the 2 forces equal.
- Q.09
A light airplane's piston engine is making 240 horsepower. Taking the typical figure of 0.5 pound of fuel an hour for each horsepower, how much fuel does it burn each minute?
FAA-H-8083-30B, ch. 5, p. 5-19
- A120 pounds
- B2 pounds
- C8 pounds
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
2 pounds
At 0.5 pound an hour for each horsepower, 240 horsepower burns 240 times 0.5, or 120 pounds an hour. There are 60 minutes in an hour, so that is 120 divided by 60, or 2 pounds a minute. 120 is the hourly figure left unconverted, and 8 comes from dividing the horsepower by 0.5 instead of multiplying, which gives 480 pounds an hour, or 8 a minute.
- Q.10
A gravity-fed carburetor needs 2 psi of fuel pressure at its inlet. Taking avgas at 6 pounds a gallon and a gallon as 231 cubic inches, about how far above the inlet must the fuel level stand?
FAA-H-8083-30B, ch. 5, p. 5-27
- A55.4 inches
- B462 inches
- C77 inches
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
77 inches
The pressure at the bottom of a column of liquid depends on its height. A column 1 square inch across and 231 inches tall holds 1 gallon, which in avgas weighs 6 pounds, so every 231 inches of fuel gives 6 psi. 2 psi needs 2 times 231 divided by 6, which is 77 inches. Using the weight of water, 8.34 pounds a gallon, gives 55.4, and leaving the weight of the fuel out gives 462.
We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.
How a missed code comes back at the oral
Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.I.J. The examiner reads those codes before your oral and practical.
The General oral runs from 4 questions if your written was clean up to 22, because every code you missed adds 1 more. General also carries 9 practical projects, each with 2 questions attached.
Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.
Questions people ask about physics for aviation
Q.01What does Boyle’s law say?
At a constant temperature, the volume of a confined gas varies inversely with its absolute pressure: double the absolute pressure and the volume halves. Charles’s law is the other half of the picture, with pressure held constant and volume rising and falling with absolute temperature.
Q.02What is the difference between gauge pressure and absolute pressure?
Gauge pressure is measured above the pressure of the air around the gauge, which is why a gauge open to the air reads 0. Absolute pressure is measured from a perfect vacuum, so it is gauge pressure plus the pressure of the atmosphere.
Q.03What is mechanical advantage?
How many times a machine multiplies the force put into it. A lever with the effort 4 times farther from the fulcrum than the load has a mechanical advantage of 4: 25 pounds of effort lifts 100 pounds, but the effort has to move 4 times as far.
Q.04What is Bernoulli’s principle?
When a fluid flows through a narrowing, it speeds up and its pressure drops, because its total energy stays the same and the gain in velocity is paid for in pressure. It is how a venturi works, and it is part of how a wing makes lift.
Q.05How many physics for aviation questions are on the FAA A&P General test?
The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Physics for Aviation subject area 5 to 10% of the General test, which is 3 to 6 of the 60 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.
Q.06Which FAA handbook chapter covers physics for aviation?
Chapter 5 of FAA-H-8083-30B, the Aviation Maintenance Technician Handbook: General, titled "Physics for Aviation". It runs from pages 5-1 to 5-62, and the FAA publishes the whole handbook free as a PDF.
Read the documents, not us
Every fact on this page was read from these on 19 August 2026 and 15 November 2026. They are the authority and we are the summary. If we and one of them disagree, they are right.
- FAA-H-8083-30B, Aviation Maintenance Technician Handbook: General, chapter 5www.faa.gov
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standardswww.faa.gov
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards: the written test blueprints (pages 13 and 14) and chapters 6 and 7www.faa.gov
- FAA, Frequently Missed Knowledge Test ACS Codes, 2nd Quarter CY25www.faa.gov
FREE PLAN · NO CARD · 25 QUESTIONS TO START
The bank holds 377 physics for aviation questions.
Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.
Start freeOr answer a few first. The free FAA A&P practice test runs on the page, with no account.