PrepAMT Academy

AMP · PRACTICE QUESTIONS · WRITTEN FOR THIS PAGE

Free FAA A&P Powerplant practice questions

15 practice questions for the FAA A&P Powerplant written test (AMP), in its own format: 3 options and 1 correct answer. Each names the FAA handbook page it was written from, and its answer and reason are one tap away. The test itself is 100 questions in 2 hours, 70% to pass, and the FAA A&P Powerplant written test page has everything else about it.

Questions written from FAA-H-8083-32B to FAA-S-ACS-1, the current Airman Certification Standards.

01 THE QUESTIONSAMP · 15 QUESTIONS

FAA A&P Powerplant practice questions and answers

They come from 9 of the Powerplant test’s subjects, no more than 2 from any one. Pick your answer, then open each question to see the right one and the reason.

  1. Q.01

    At overhaul you find that the fir-tree blades of a cold turbine wheel rock slightly in their slots in the disc rim. What does this tell you?

    FAA-H-8083-32B, ch. 1, p. 1-49

    1. AThe disc slots have worn oversize, so the disc must be rejected
    2. BThe blade locking tabs have failed, so each blade must be locked in again
    3. CIt is normal, since the disc grows when hot and the roots then fit tight
    SHOW THE ANSWER

    THE ANSWER IS C.

    It is normal, since the disc grows when hot and the roots then fit tight

    Fir-tree slots are cut with some clearance around the blade roots, so a blade can move a little in its slot while the disc is cold. The gap is there for thermal expansion: as the disc heats up in operation it grows, the clearance closes and the roots fit tightly in the rim. Slight play on a cold wheel is expected, not a sign of a worn disc or failed locking.

  2. Q.02

    A turbine engine uses 3 turbine wheels to drive its compressor, fan and accessories. How many rows of turbine nozzle vanes does its turbine section have?

    FAA-H-8083-32B, ch. 1, p. 1-50

    1. A1, a single row at the turbine inlet that feeds all 3
    2. B3, since a nozzle row comes ahead of every wheel
    3. C2, one between each pair of wheels
    SHOW THE ANSWER

    THE ANSWER IS B.

    3, since a nozzle row comes ahead of every wheel

    However many wheels a turbine needs to drive the engine's components, there is always a turbine nozzle ahead of each wheel. A row of stationary nozzles followed by a row of rotating blades makes one stage, so 3 wheels means 3 nozzle rows. Each nozzle row turns heat and pressure into fast gas and aims it the way its own wheel turns, a job a single row at the inlet could not do for the wheels behind it.

  3. Q.03

    A pilot reports that the engine ran rough and lost power while flying through cool, moist air. On the ground it passes every check and runs perfectly. What should you keep in mind?

    FAA-H-8083-32B, ch. 3, p. 3-3

    1. AInduction ice can cause that in the air and leave no trace on the ground
    2. BAn engine that runs perfectly on the ground cannot have that fault
    3. CThe roughness must come from fouled plugs that cleared on the way down
    SHOW THE ANSWER

    THE ANSWER IS A.

    Induction ice can cause that in the air and leave no trace on the ground

    Even when an inspection shows everything in proper working order and the engine runs perfectly on the ground, induction system ice can make it run erratically and lose power in the air. Many engine troubles blamed on other sources are actually caused by induction icing, which is why a mechanic needs to know how and where it forms. A clean ground run does not clear the engine, and blaming the plugs with no evidence ignores the likeliest cause in that weather.

  4. Q.04

    You are about to set the idle mixture on a Continental (TCM) continuous-flow fuel injection system. What has to be checked and set first?

    FAA-H-8083-32B, ch. 2, p. 2-30

    1. AThat the throttle stop is at the final idle rpm
    2. BThat the flow divider holds the nozzle lines closed
    3. CThat the fuel pump pressures are set correctly
    SHOW THE ANSWER

    THE ANSWER IS C.

    That the fuel pump pressures are set correctly

    On the Continental (TCM) system, fuel pump pressure is part of the basic calibration, so the pump pressures are serviced and set correctly before any idle adjustment is made. Otherwise the idle mixture is tailored to a wrong starting point. The idle stop is reset to the specified rpm after the mixture has been adjusted, not before. A flow divider belongs to the Bendix RSA system; the TCM system uses a manifold valve.

  5. Q.05

    Working on the line with no gauge for contact pad thickness, you find a magneto's breaker points pitted. What makes it hard to judge by eye whether they can stay in service?

    FAA-H-8083-32B, ch. 4, p. 4-40

    1. AA pit is always hidden under the matching peak on the other contact
    2. BLong service and earlier dressings may already have thinned the platinum pad
    3. CPits of any depth are normal wear, so they show nothing about condition
    SHOW THE ANSWER

    THE ANSWER IS B.

    Long service and earlier dressings may already have thinned the platinum pad

    A pit is worse than the matching peak because it goes down into the platinum pad on the contact face, so whether pitted points can stay in service depends on how much of the original platinum is left. That is hard to judge by eye, because long service and earlier dressings may already have left the pad thin. Overhaul shops measure the pad with a gauge, but line stations usually have none. The pit does not hide under the peak, and deep pitting is not normal wear.

  6. Q.06

    One magneto on a 6-cylinder, 4-stroke engine fires a plug in every cylinder. With the engine turning 2,400 rpm, how many sparks a minute does that magneto deliver?

    FAA-H-8083-32B, ch. 4, p. 4-6

    1. A7,200 sparks
    2. B14,400 sparks
    3. C1,200 sparks
    SHOW THE ANSWER

    THE ANSWER IS A.

    7,200 sparks

    On a 4-stroke engine each cylinder fires once every 2 turns of the crankshaft, which is why the distributor rotor turns at half crankshaft speed. At 2,400 rpm the rotor turns 1,200 times a minute and passes all 6 electrodes on each turn, so the magneto fires 1,200 times 6, or 7,200 sparks a minute. 14,400 leaves out the half speed, and 1,200 is the rotor speed alone.

  7. Q.07

    After a flight, a pilot reports that the rpm of the constant-speed propeller shifted a little as the airplane's attitude and airspeed changed, then held steady. What is your call?

    FAA-H-8083-32B, ch. 7, p. 7-30

    1. AThe propeller is hunting and should go to a repair facility
    2. BSmall changes like that are normal and no cause for concern
    3. CThe governor speeder spring has weakened and must be replaced
    SHOW THE ANSWER

    THE ANSWER IS B.

    Small changes like that are normal and no cause for concern

    A governor holds the selected rpm by changing blade angle when a change in attitude or airspeed upsets it, so small swings in engine speed as the airplane maneuvers are normal and no cause for concern. Hunting is something else: a repeated, cyclic swing above and below the desired speed. A small change that settles on its own points to no worn governor part.

  8. Q.08

    One-piece aluminum fixed-pitch propellers took over from wood ones on many airplanes. Compared with wood, why did they give the engine more efficient cooling?

    FAA-H-8083-32B, ch. 7, p. 7-13

    1. ATheir metal hub drew heat away from the crankshaft flange
    2. BTheir bright finish reflected heat back away from the cowling
    3. CTheir blades kept useful effective pitch nearer the hub
    SHOW THE ANSWER

    THE ANSWER IS C.

    Their blades kept useful effective pitch nearer the hub

    The handbook lists what the one-piece aluminum propeller gained over wood: less weight, since there are no blade-clamping devices; a lower maintenance cost, since it is made in one piece; pitch that a propeller repair station can change within limits by twisting a blade; and more efficient cooling, because the effective pitch is kept nearer the hub, where the air goes back over the engine. Neither the hub metal nor the finish is what did it.

  9. Q.09

    Removing a cylinder, you have the piston at top dead center on the compression stroke and are about to depress the rocker arms to take out the pushrods. Why back the adjusting nut off as far as it will go first?

    FAA-H-8083-32B, ch. 10, p. 10-41

    1. AIt gives the most clearance for pulling out the pushrods
    2. BIt sets the valve clearance to zero, ready for reassembly later
    3. CIt lets the rocker box cover come off without prying
    SHOW THE ANSWER

    THE ANSWER IS A.

    It gives the most clearance for pulling out the pushrods

    Putting the piston at top dead center on compression takes the pressure off both rocker arms. Backing the adjusting nut off as far as possible then gives the most clearance for the pushrods when the rocker arms are depressed. The rocker box covers are already off by this stage, tapped loose with a rawhide or plastic mallet rather than pried, and the valve clearance is set again when the cylinder goes back on.

  10. Q.10

    A turbine engine has been run at high power on the ground for a long trim run. Why should it idle for about 5 minutes before it is shut down?

    FAA-H-8083-32B, ch. 10, p. 10-58

    1. ASo the oil can drain back to the tank and the oil level reads true
    2. BSo the case does not cool and shrink onto the still-hot turbine wheels
    3. CSo the fuel control can purge its vapor and the next start will not hang
    SHOW THE ANSWER

    THE ANSWER IS B.

    So the case does not cool and shrink onto the still-hot turbine wheels

    After shutdown the turbine case loses its heat fast, since cooling air reaches it inside and out, but the heavy turbine wheels hold their heat much longer. Shut down hot, the case can shrink onto wheels that are still turning, so the blades squeal or the rotor seizes. About 5 minutes at idle after a long high-power run lets the temperatures even out first.

  11. Q.11

    On a large radial engine, the exhaust tailpipe joins the collector ring through a telescoping expansion joint. What does that joint allow a mechanic to do?

    FAA-H-8083-32B, ch. 3, p. 3-22

    1. ASwing the tailpipe aside to reach the cylinders behind it
    2. BFit a cabin heat muff around the ring without cutting it
    3. CTake off segments of the collector ring without removing the tailpipe
    SHOW THE ANSWER

    THE ANSWER IS C.

    Take off segments of the collector ring without removing the tailpipe

    The collector ring on a large radial is built in sections, each one collecting the exhaust of 2 cylinders, and the tailpipe is joined to it by a telescoping expansion joint. That joint gives enough slack for segments of the ring to be taken off without removing the tailpipe. It does not let the tailpipe swing out of the way, and a heat muff, where fitted, is part of the tailpipe assembly, not something the joint makes room for.

  12. Q.12

    On a Rotax 914, the red boost lamp starts to blink once full throttle has been held for more than 5 minutes. Why should the pilot not keep full power on past that point?

    FAA-H-8083-32B, ch. 11, p. 11-9

    1. AThe 2 electric fuel pumps cannot keep up with full-boost fuel flow beyond that time
    2. BFull power held longer can overstress the engine, both thermally and mechanically
    3. CThe turbocharger is oiled only in short bursts and starts to run dry at full boost
    SHOW THE ANSWER

    THE ANSWER IS B.

    Full power held longer can overstress the engine, both thermally and mechanically

    The red boost lamp helps the pilot keep full power to no more than 5 minutes, because beyond that the engine could suffer thermal and mechanical overstress. The limit protects the engine itself. The turbocharger plain bearings are fed steadily through their own oil line from the main oil pump, and the 2 electric fuel pumps in series feed the carburetors through the fuel pressure control, so neither supply is what sets the 5 minutes.

  13. Q.13

    Before the first start of the day, with the engine still at the outside temperature, the cylinder head temperature gauge reads close to the outside air temperature. What does that tell you?

    FAA-H-8083-32B, ch. 6, p. 6-37

    1. AThe indicating system passes one simple check that it is working
    2. BThe gauge is faulty, since a working one reads zero until the engine runs
    3. CThe probe is on the coolest cylinder rather than the hottest one
    SHOW THE ANSWER

    THE ANSWER IS A.

    The indicating system passes one simple check that it is working

    With the engine at ambient temperature, a cylinder head temperature indicator should show the free outside air temperature, and seeing that is one test that the instrument is working correctly. A working gauge does not read zero on a cold engine. Before the start every cylinder sits at the same outside temperature, so the reading says nothing about where the probe is, although it belongs on the hottest cylinder, as found in the block test.

  14. Q.14

    Your shop can ship a removed engine in a container it is lowered into vertically, or in a type that takes it horizontally. What does the horizontal type do away with?

    FAA-H-8083-32B, ch. 8, p. 8-21

    1. AThe silica gel bags, since the base seals the engine by its own weight
    2. BThe dehydrated air charge, since a level engine traps no moisture
    3. CAn extra hoist, since the engine is simply lowered onto the base and secured
    SHOW THE ANSWER

    THE ANSWER IS C.

    An extra hoist, since the engine is simply lowered onto the base and secured

    Engines go into shipping containers sealed in an envelope, and in the usual case the engine is lowered vertically onto the base and bolted to it. Another type takes the engine horizontally, which does away with the need for an extra hoist: the engine is simply lowered onto the base portion of the container and secured. Silica gel bags still go in afterward, usually in a special section, and lying level does nothing on its own to keep moisture out.

  15. Q.15

    An engine is being sealed into a metal shipping container, with ventilatory plugs in its spark plug holes instead of dehydrator plugs. What keeps the inside of the engine dry while it is stored?

    FAA-H-8083-32B, ch. 8, p. 8-21

    1. AThe silica gel bags in the container, through the plugs
    2. BThe dehydrated air charge alone, with no desiccant needed
    3. CPreservative oil sprayed in, which seals out all moisture
    SHOW THE ANSWER

    THE ANSWER IS A.

    The silica gel bags in the container, through the plugs

    In a metal container the engine's openings normally get ventilatory plugs rather than dehydrator plugs, so the silica gel bags placed in the container have to dehydrate the inside of the engine through them. The container is also charged with dehydrated air, but the handbook gives the drying job inside the engine to the silica gel. Corrosion-preventive compound only insulates against moisture, and in excessive moisture it eventually breaks down.

We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.

03 COMMON QUESTIONSFAQ

About these practice questions

Q.01

Are these real FAA A&P Powerplant test questions?

No. We wrote them for this page from FAA-H-8083-32B, the FAA’s Powerplant handbook, and each one names the page it was written from so you can check it. They are not FAA test questions, and none of them comes from our question bank.

Q.02

How should I use these FAA A&P Powerplant practice questions?

Answer each one before you open it, and note the ones you miss. A miss points at a subject, and each subject has its own page below, with more questions on it and how much of the Powerplant test it is.

Q.03

How many questions are on the FAA A&P Powerplant test?

100, in 2 hours, with 70% to pass. Everything else about the test is on the FAA A&P Powerplant written test page.

Q.04

Where can I practice more FAA A&P Powerplant questions?

Our bank holds 3,450 Powerplant questions across 11 subjects, each with a written explanation. A free account gives you one free set, 25 questions and 25 fill-in-the-gaps from any subject you pick, once, and Pro opens the rest.

FREE PLAN · NO CARD · 25 QUESTIONS TO START

The bank holds 3,450 FAA A&P Powerplant questions.

Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.

Start free

Or answer a few first. The free FAA A&P practice test runs on the page, with no account.