AMP · PP-03 · FAA-H-8083-32B CH. 3
FAA A&P Powerplant: Induction and Engine Airflow Systems
For the FAA A&P Powerplant test, engine induction and exhaust systems is chapter 3 of FAA-H-8083-32B, Induction & Exhaust Systems. Its main ACS subject area, Reciprocating Engine Induction and Cooling Systems, is 5 to 10% of the test, or 5 to 10 of its 100 scored questions. Our question bank holds 245 questions on it, and the 10 below were written for this page.
Test shares and most-missed codes read from the FAA on 15 November 2026.
What FAA-H-8083-32B chapter 3 covers
Chapter 3 covers reciprocating engine induction: the basic carburetor induction system, air filters, carburetor heat and alternate air, induction icing, and supercharging, from internally driven superchargers to turbosuperchargers with their wastegates and controllers, with troubleshooting. It covers turbine engine inlets and their ice and debris protection.
The other half is exhaust: reciprocating engine exhaust systems, their inspection and maintenance, collector rings and augmentors, then turbine engine exhaust, nozzles, thrust reversers, afterburners and noise suppression.
It runs from pages 3-1 to 3-31 of the Aviation Maintenance Technician Handbook: Powerplant, which the FAA publishes free as a PDF.
How much of the FAA A&P Powerplant test it is
- 5 to 10%OF THE TESTACS area AM.III.J
- 5 to 10QUESTIONSof 100 scored
- 245IN OUR BANKquestions on this subject
The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Reciprocating Engine Induction and Cooling Systems (AM.III.J) is 5 to 10% (5 to 10 questions) on the 100-question Powerplant test. Our Induction and Engine Airflow Systems questions also reach into Turbine Engine Air Systems (AM.III.K, 5 to 10%) and Engine Exhaust and Reverser Systems (AM.III.L, 5 to 10%). The 13 ranges for the Powerplant test add up to anywhere from 65% to 140%, so they say how big an area can get, not how many questions you will see from it.
Reciprocating Engine Induction and Cooling Systems is not ours alone to cover: our Lubrication and Cooling Systems questions are written to the same area.
No code in these areas is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.
Engine induction and exhaust systems questions and answers
10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.
- Q.01
A screen-type carburetor air filter has an aluminum alloy frame holding a deeply crimped screen. What does the crimping give it?
FAA-H-8083-32B, ch. 3, p. 3-2
- AA finer mesh, so it stops smaller particles than a flat screen would
- BThe greatest possible screen area facing the incoming air
- CGrooves that drain trapped water away before it reaches the carburetor
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
The greatest possible screen area facing the incoming air
The carburetor air filter sits in the air scoop in front of the carburetor air duct and stops dust and other foreign matter from entering the engine. Its screen is deeply crimped and arranged so that it presents the greatest possible screen area to the airstream. Crimping does not make the mesh any finer, and the screen is not there to drain water.
- Q.02
On a dusty strip, an engine runs on its filtered alternate air inlet, which draws air in through a louvered panel that does not face into the airstream. How does that placement help keep dust out?
FAA-H-8083-32B, ch. 3, p. 3-4
- ASolid dust keeps going straight as the air turns to enter, so most is left behind
- BAir entering there has already passed the cooling fins, which catch the dust
- CThe side-facing panel builds ram pressure that blows the dust back out again
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Solid dust keeps going straight as the air turns to enter, so most is left behind
With the dust filter system in use, air comes in through a louvered access panel that does not face straight into the airstream, so it has to turn to enter the duct. The dust particles are solid and tend to carry on in a straight line, so most of them are separated right there, and the filter easily removes those drawn into the louvers. A panel that does not face the airstream gets little ram effect, and the cooling fins play no part in it.
- Q.03
You are refitting an exhaust stack, and the manufacturer uses brass high-temperature locknuts at the cylinder port. The bin only has standard steel self-locking nuts of the same size. What do you do?
FAA-H-8083-32B, ch. 3, p. 3-24
- AFit the steel self-locking nuts, since steel is stronger than brass
- BFit the steel nuts and put a lock washer under each one for the heat
- CGet the correct high-temperature locknuts before fitting the stack
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Get the correct high-temperature locknuts before fitting the stack
Exhaust work calls for the proper hardware and clamps every time. Steel or low-temperature self-locking nuts must not be substituted for the brass or special high-temperature locknuts the manufacturer uses, however strong they are, and a lock washer does not make an unsuitable nut fit for that heat. So the job waits for the right nuts. Old exhaust gaskets are never reused either; fit new ones of the same type.
- Q.04
On an older radial engine with augmentor tailpipes, each tailpipe has a cross-sectional area of 60 square inches. With its augmentor vane fully closed, about how much of that area is left open?
FAA-H-8083-32B, ch. 3, p. 3-22
- A27 square inches
- B33 square inches
- C87 square inches
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
33 square inches
With the vane fully closed, the handbook says the tailpipe's cross-sectional area is reduced by approximately 45 percent, so about 55 percent of it is left open. 60 times 0.55 is 33 square inches. 27 square inches is the part the vane closes off, and 87 comes from adding the 45 percent on instead of taking it away. Moving the vanes toward closed slows the flow through the augmentor, and that raises the engine temperature.
- Q.05
A military jet has been climbing in afterburner, and the pilot now brings the power lever back out of afterburner to normal full power. What should its variable-area exhaust nozzle do?
FAA-H-8083-32B, ch. 3, p. 3-29
- AOpen wider still, so the cooling liner gets more air once the extra fuel stops
- BStay where it is, since the nozzle area is only changed for takeoff and landing
- CClose down again, since the extra energy and mass are no longer in the flow
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Close down again, since the extra energy and mass are no longer in the flow
Lighting the afterburner burns extra fuel in the exhaust, and as energy and mass are added to the gas flow the nozzle has to open wider to pass it. Bringing the power lever back out of afterburner takes that extra flow away, so the nozzle closes down again. The liner around the nozzle is cooled by air circulating around it, not by opening the nozzle, and the nozzle moves with afterburner use, not with the phase of flight.
- Q.06
Some turbine compressor inlet screens are made retractable, so they can be withdrawn after takeoff or when icing conditions prevail. What drawback comes with that design?
FAA-H-8083-32B, ch. 3, p. 3-18
- AThey are open to mechanical failure and add weight and bulk to the installation
- BThe compressor is left with no screen in front of it during the takeoff run
- CThe screen cannot be pulled clear any more once icing has already begun
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
They are open to mechanical failure and add weight and bulk to the installation
A fixed inlet screen adds pressure loss and is very prone to icing, so some installations make the screen retractable and withdraw it after takeoff or whenever icing conditions prevail. The cost is that such screens are subject to mechanical failure and add both weight and bulk. The screen stays in place for the takeoff run, when it is wanted, and the point of retracting it is to pull it clear when icing is a risk.
- Q.07
A pilot keeps reporting rough running and power loss in cruise on cloudy, humid days. Every ground run and inspection finds the engine in perfect order. What should you suspect?
FAA-H-8083-32B, ch. 3, p. 3-3
- AA dirty induction air filter cutting the airflow
- BInduction system ice forming in the moist air
- CSpark plugs fouled during the long ground runs
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Induction system ice forming in the moist air
Induction system ice can make an engine run erratically and lose power in the air even when an inspection shows everything in order and the engine runs perfectly on the ground, and many engine troubles blamed on other causes turn out to be icing. It can form in cloud, fog or clear air with high humidity. A dirty filter or fouled plugs would show up on the ground run or at the inspection.
- Q.08
On a hot day, the cooling air passages of a turbocharged engine's aftercooler are found packed with dirt and grass. What is the main risk in a full-power takeoff?
FAA-H-8083-32B, ch. 3, p. 3-14
- AThrottle ice forming as the charge expands past the plate
- BThe waste gate sticking open so the boost falls away
- CVery hot charge air pushing the engine toward detonation
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Very hot charge air pushing the engine toward detonation
Compressing the induction air heats it a great deal: on a 100 °F day the air can leave a turbocharger compressor at up to 500 °F, well over the 230 to 300 °F that throttle inlets typically allow. The aftercooler takes that heat out, which lowers the risk of detonation and makes the charge denser. Choke its cooling air and the hot charge brings the combustion chambers closer to detonation. Air that hot cannot form throttle ice, and a dirty aftercooler does nothing to the waste gate.
- Q.09
You need to take off one section of the exhaust collector ring on a 14-cylinder radial engine. What holds that section in place on the engine?
FAA-H-8083-32B, ch. 3, p. 3-22
- ABolts to a bracket on the blower section, plus a sleeve joint at the short stack
- BThe tailpipe's telescoping joint, which hangs the whole ring from the tailpipe
- CWelds to the sections either side, since the ring only comes off in 1 piece
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Bolts to a bracket on the blower section, plus a sleeve joint at the short stack
The 14-cylinder ring is made in 7 sections. Each section is bolted to a bracket on the blower section of the engine and is partly supported by a sleeve connection between the ring's ports and the short stacks on the engine exhaust ports. The tailpipe joins the ring through a telescoping expansion joint, which gives enough slack to remove a section without taking the tailpipe off, so the sections come off one at a time.
- Q.10
On a typical opposed engine, the exhaust collector tubes end at ejectors near the firewall. What do the ejectors do?
FAA-H-8083-32B, ch. 3, p. 3-22
- AQuiet the exhaust in place of a separate muffler
- BHold exhaust back pressure even at every cylinder
- CPull cooling air through the engine compartment
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Pull cooling air through the engine compartment
The collector tubes are tapered so the exhaust reaches the ejectors at the right speed. Each ejector is a throat and duct that uses the pumping action of that gas stream to draw a flow of cooling air through all parts of the engine compartment, the same pumping action an augmenter tube uses. They are not mufflers, and they do nothing to even out back pressure at the cylinders.
We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.
How a missed code comes back at the oral
Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.III.J or AM.III.K or AM.III.L. The examiner reads those codes before your oral and practical.
The Powerplant oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Powerplant also carries 11 practical projects, each with 2 questions attached.
Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.
Questions people ask about engine induction and exhaust systems
Q.01What does a turbocharger wastegate do?
It regulates how much exhaust goes to the turbine. Fully closed, it forces all of the exhaust through the turbine wheel, which drives the compressor harder; partly closed, it sends a matching share through and lets the rest bypass the turbine.
Q.02Why is an engine exhaust system inspected so carefully?
Because a failure can cause carbon monoxide poisoning of the people on board, a partial or complete loss of power, or a fire. A failed heat exchanger can also let exhaust into the induction system and overheat the engine. Cracks, leaking gaskets and broken parts are what to look for.
Q.03What is a thrust reverser?
A system that turns a turbine engine’s exhaust or fan air forward to help stop the aircraft after landing, since heavier, faster landing aircraft cannot rely on their brakes alone. Mechanical blockage types put an obstruction in the exhaust stream behind the nozzle; aerodynamic blockage types turn the flow with vanes, as fan reversers do with cascade vanes.
Q.04What is the difference between a supercharger and a turbosupercharger?
An internally driven supercharger is driven from the engine through a mechanical connection and compresses the fuel and air mixture after it leaves the carburetor. A turbosupercharger, or turbocharger, is driven by the exhaust and compresses the air before it is mixed with the fuel.
Q.05How many engine induction and exhaust systems questions are on the FAA A&P Powerplant test?
The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Reciprocating Engine Induction and Cooling Systems subject area 5 to 10% of the Powerplant test, which is 5 to 10 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it. Our Induction and Engine Airflow Systems questions also reach into Turbine Engine Air Systems (5 to 10%) and Engine Exhaust and Reverser Systems (5 to 10%).
Q.06Which FAA handbook chapter covers engine induction and exhaust systems?
Chapter 3 of FAA-H-8083-32B, the Aviation Maintenance Technician Handbook: Powerplant, titled "Induction & Exhaust Systems". It runs from pages 3-1 to 3-31, and the FAA publishes the whole handbook free as a PDF.
Read the documents, not us
Every fact on this page was read from these on 19 August 2026 and 15 November 2026. They are the authority and we are the summary. If we and one of them disagree, they are right.
- FAA-H-8083-32B, Aviation Maintenance Technician Handbook: Powerplant, chapter 3www.faa.gov
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standardswww.faa.gov
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards: the written test blueprints (pages 13 and 14) and chapters 6 and 7www.faa.gov
- FAA, Frequently Missed Knowledge Test ACS Codes, 2nd Quarter CY25www.faa.gov
More FAA A&P Powerplant subjects
FREE PLAN · NO CARD · 25 QUESTIONS TO START
The bank holds 245 engine induction and exhaust systems questions.
Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.
Start freeOr answer a few first. The free FAA A&P practice test runs on the page, with no account.