AMP · PP-06 · FAA-H-8083-32B CH. 6
FAA A&P Powerplant: Lubrication and Cooling Systems
For the FAA A&P Powerplant test, engine lubrication and cooling systems is chapter 6 of FAA-H-8083-32B, Lubrication & Cooling Systems. Its main ACS subject area, Engine Lubrication Systems, is 5 to 10% of the test, or 5 to 10 of its 100 scored questions. Our question bank holds 317 questions on it, and the 10 below were written for this page.
Test shares and most-missed codes read from the FAA on 15 November 2026.
What FAA-H-8083-32B chapter 6 covers
Chapter 6 covers engine oil: what it has to do, the properties that matter such as viscosity and flash point, and the oils used in reciprocating and turbine engines. It covers wet sump and dry sump lubrication systems and their parts, from tanks, pumps and filters to relief valves, coolers and thermostatic bypass valves, and oil system maintenance, with filter and screen inspection, chip detectors and spectrometric oil analysis.
The cooling half covers how reciprocating engines are cooled, with cylinder fins, baffles and cowl flaps, and how turbine engines are cooled, with the inspection and maintenance of both.
It runs from pages 6-1 to 6-40 of the Aviation Maintenance Technician Handbook: Powerplant, which the FAA publishes free as a PDF.
How much of the FAA A&P Powerplant test it is
- 5 to 10%OF THE TESTACS area AM.III.G
- 5 to 10QUESTIONSof 100 scored
- 317IN OUR BANKquestions on this subject
The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Engine Lubrication Systems (AM.III.G) is 5 to 10% (5 to 10 questions) on the 100-question Powerplant test. Our Lubrication and Cooling Systems questions also reach into Reciprocating Engine Induction and Cooling Systems (AM.III.J, 5 to 10%). The 13 ranges for the Powerplant test add up to anywhere from 65% to 140%, so they say how big an area can get, not how many questions you will see from it.
No code in these areas is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.
Engine lubrication and cooling systems questions and answers
10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.
- Q.01
To give a sense of the heat a piston engine has to get rid of, how much water could the heat value of 1 gallon of aviation gasoline bring to a boil?
FAA-H-8083-32B, ch. 6, p. 6-32
- AAbout 7.5 gallons
- BAbout 750 gallons
- CAbout 75 gallons
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
About 75 gallons
1 gallon of aviation gasoline has enough heat value to boil about 75 gallons of water, so an engine burning 4 gallons a minute is releasing a huge amount of heat. Only about a quarter of it becomes useful power. Of the rest, about half goes out with the exhaust and the other half soaks into the engine, where the oil and the cooling air have to carry it away before it damages the cylinders.
- Q.02
Refitting the cowling on an engine with full cylinder head baffling, you see a long piece of the rubber air seal on one panel has torn away. What will that do if it is left?
FAA-H-8083-32B, ch. 6, p. 6-36
- ALet cooling air slip along the panel instead of passing through the baffles
- BNothing much, since the baffles alone guide the air around the heads
- COvercool the cylinders by letting extra outside air into the cowling
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Let cooling air slip along the panel instead of passing through the baffles
The air seal is rubber, bolted to a rib inside the cowl panel. On an engine whose baffles cover the cylinder heads, it closes the gap between panel and baffles, so the cooling air has to go around and through the baffle system. With a piece missing, air escapes along the inside of the panel without circulating around the cylinders, so those cylinders get less cooling, not more. That is why the seal is checked for damage at every cowl inspection.
- Q.03
In a wet-sump reciprocating engine, why is the oil pump designed to make more pressure than the engine actually needs?
FAA-H-8083-32B, ch. 6, p. 6-13
- ASo the relief valve stays shut at every engine speed and load
- BTo make up for bearing wear and for oil that thins out
- CSo it can spray oil straight onto the cylinder walls
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
To make up for bearing wear and for oil that thins out
The pump is built to make more pressure than the engine needs so that oil pressure holds up as the bearings wear and their clearances open, and when the oil thins out. Changes in pump speed between idle and full throttle, and in oil viscosity with temperature, are taken care of by the tension on the relief valve spring, so the relief valve is very much part of the system. The cylinders and pistons get their oil from the spray thrown off the pressure-fed parts.
- Q.04
On a turbine engine, the last-chance filters at the bearing oil jets cannot be reached for cleaning except during engine maintenance. What routine check helps keep them from clogging?
FAA-H-8083-32B, ch. 6, p. 6-25
- AChecking the main oil filters often for contamination
- BFlushing each oil jet with solvent at every oil change
- CRunning the engine at high power for a while after each start
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Checking the main oil filters often for contamination
The oil jets have tiny orifices, and the last-chance filter at each one keeps debris out of it. If one clogs, the bearing it feeds usually fails, and the jets cannot be reached for cleaning except during engine maintenance. So the defense is upstream: the main oil filters are checked often for contamination, so dirt is caught and its source found before it gets that far. A jet that cannot be reached cannot be flushed at an oil change, and running hard after a start cleans nothing.
- Q.05
After a cold night, a piston engine is started on oil that has thickened. Why are the cylinder walls among the last parts to get enough oil?
FAA-H-8083-32B, ch. 6, p. 6-12
- AThe pressure pump feeds the valve train first and the walls last of all
- BThe cold oil cooler holds back most of the flow until it warms up
- CTheir oil first has to seep out through the tight crankpin clearances
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Their oil first has to seep out through the tight crankpin clearances
Oil under pressure runs through drilled passages to the main bearings, then through holes in the crankshaft to the connecting rod bearings. The cylinder walls get theirs as spray thrown off the crankshaft and the crankpin bearings, and that oil first has to seep out through the small crankpin clearances. That takes time, and longer on a cold day when the oil is sluggish, which is one of the chief reasons for multiviscosity oils that flow well when cold. No pump line feeds the walls directly, and cold oil bypasses the cooler rather than being held back by it.
- Q.06
While servicing a turbine engine you spill some turbine oil down a painted cowl panel. Why should it be wiped off straight away?
FAA-H-8083-32B, ch. 6, p. 6-20
- AIt soaks into the aluminum skin and starts corrosion underneath
- BIt can blister or discolor the paint, or remove it
- CIt hardens the paint so it chips the next time the panel flexes
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
It can blister or discolor the paint, or remove it
Spilled turbine oil can blister the finish, discolor it or take it off altogether, so the handbook has painted surfaces wiped clean with a petroleum solvent after a spill. Gloves and eye protection are worn for the job, since turbine oil left on the skin for long, or again and again, can irritate it.
- Q.07
With the cowling off, you find a dent in one cylinder baffle and a crack that has only just started in another. Neither is severe. What can be done?
FAA-H-8083-32B, ch. 6, p. 6-37
- AStraighten the dent and stop-drill the crack, then keep both in service
- BReplace both baffles, since any crack or any dent rules out a baffle
- CLeave both as they are, since a baffle carries no load and never needs repair
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Straighten the dent and stop-drill the crack, then keep both in service
Baffles and deflectors are checked for cracks, dents and loose hold-down studs whenever the cowling comes off. Damage severe enough calls for repair, or removal and replacement. A crack that has only just started can be stop-drilled, though, and a dent can be straightened, so the baffle can stay in service. Leaving them alone is no answer either: the baffles are what force the cooling air in close around the cylinders, and an untreated crack keeps growing.
- Q.08
On one cylinder head, 3 neighboring fins have pieces broken off them, 5 inches of breakage in all. The engine maker allows 4 inches in total on any 3 adjacent fins. What is the call?
FAA-H-8083-32B, ch. 6, p. 6-36
- AKeep the cylinder, since the limit is judged on one fin at a time
- BFile the broken edges smooth and return it to service
- CRemove and replace the cylinder, since the breakage is past the limit
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Remove and replace the cylinder, since the breakage is past the limit
Small fin cracks can be filled or stop-drilled and sharp corners filed, but fin breakage is judged against the maker's limits, and neighboring fins are counted together because the missing area all sits in one place. 5 inches across 3 adjacent fins is more than the 4 allowed, so too little heat can leave that spot and it runs hot. The cylinder is removed and replaced; filing the edges does not put the missing metal back.
- Q.09
A turbine engine's gerotor oil pump turns all its elements on one shaft. The pressure element is sized for 3.1 gallons per minute and a scavenge element for 4.25. About how much more oil, as a percentage, can that scavenge element move?
FAA-H-8083-32B, ch. 6, p. 6-23
- AAbout 27 percent
- BAbout 37 percent
- CAbout 137 percent
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
About 37 percent
The scavenge element moves 4.25 minus 3.1, or 1.15 gallons per minute more, and 1.15 divided by the pressure element's 3.1 is about 0.37, so it moves about 37 percent more. Dividing 1.15 by 4.25 instead gives the 27 percent slip, and 137 percent is the whole scavenge capacity taken as a share of the pressure element's. Since all the elements turn on a common shaft, the difference comes from making the pressure gerotor smaller than the scavenge ones.
- Q.10
Baffles and cylinder deflectors resist the passage of cooling air, so a good pressure difference has to be kept across the engine to push air through them. What is gained in return?
FAA-H-8083-32B, ch. 6, p. 6-37
- AFar less cooling air is needed to cool the cylinders
- BThe cowl flaps can stay shut in every phase of flight
- CThe oil cooler no longer needs an air-exit door of its own
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Far less cooling air is needed to cool the cylinders
Baffles and deflectors make the cooling air follow the fins closely around each cylinder instead of spilling past it. That resistance means an appreciable pressure difference has to be held across the engine to get the air through. The return is that properly designed and placed deflectors greatly reduce the volume of cooling air the engine needs. Cowl flaps and the oil cooler's exit door are still used to control temperature.
We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.
How a missed code comes back at the oral
Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.III.G or AM.III.J. The examiner reads those codes before your oral and practical.
The Powerplant oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Powerplant also carries 11 practical projects, each with 2 questions attached.
Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.
Questions people ask about engine lubrication and cooling systems
Q.01What is the difference between a wet sump and a dry sump system?
A wet sump engine stores its oil in a reservoir inside the engine and returns it there after it circulates. A dry sump engine pumps the oil out of the crankcase with a scavenge pump, through external lines, to a separate tank.
Q.02What is oil viscosity?
An oil’s resistance to flow. Oil that flows slowly has a high viscosity; oil that flows freely has a low viscosity. It is the property that matters most in how an oil works in an engine, and it changes with temperature.
Q.03What do cowl flaps do?
They control how much cooling air flows through the engine cowling. On the ground they are opened wide, since drag does not matter. On takeoff they are opened only enough to keep the engine below its red line, because open cowl flaps make drag. They are found mostly on older aircraft and radial engine installations.
Q.04What does spectrometric oil analysis show?
Every engine in service has microscopic metal particles in its oil, and the analysis measures each element in parts per million by weight, grouped as wear metals and additives. A change in the trend points to wear in the parts made of that metal, before anything fails.
Q.05How many engine lubrication and cooling systems questions are on the FAA A&P Powerplant test?
The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Engine Lubrication Systems subject area 5 to 10% of the Powerplant test, which is 5 to 10 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it. Our Lubrication and Cooling Systems questions also reach into Reciprocating Engine Induction and Cooling Systems (5 to 10%).
Q.06Which FAA handbook chapter covers engine lubrication and cooling systems?
Chapter 6 of FAA-H-8083-32B, the Aviation Maintenance Technician Handbook: Powerplant, titled "Lubrication & Cooling Systems". It runs from pages 6-1 to 6-40, and the FAA publishes the whole handbook free as a PDF.
Read the documents, not us
Every fact on this page was read from these on 19 August 2026 and 15 November 2026. They are the authority and we are the summary. If we and one of them disagree, they are right.
- FAA-H-8083-32B, Aviation Maintenance Technician Handbook: Powerplant, chapter 6www.faa.gov
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standardswww.faa.gov
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards: the written test blueprints (pages 13 and 14) and chapters 6 and 7www.faa.gov
- FAA, Frequently Missed Knowledge Test ACS Codes, 2nd Quarter CY25www.faa.gov
FREE PLAN · NO CARD · 25 QUESTIONS TO START
The bank holds 317 engine lubrication and cooling systems questions.
Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.
Start freeOr answer a few first. The free FAA A&P practice test runs on the page, with no account.