AMA · PRACTICE QUESTIONS · WRITTEN FOR THIS PAGE
Free FAA A&P Airframe practice questions
15 practice questions for the FAA A&P Airframe written test (AMA), in its own format: 3 options and 1 correct answer. Each names the FAA handbook page it was written from, and its answer and reason are one tap away. The test itself is 100 questions in 2 hours, 70% to pass, and the FAA A&P Airframe written test page has everything else about it.
Questions written from FAA-H-8083-31B to FAA-S-ACS-1, the current Airman Certification Standards.
FAA A&P Airframe practice questions and answers
They come from 10 of the Airframe test’s subjects, no more than 2 from any one. Pick your answer, then open each question to see the right one and the reason.
- Q.01
A semimonocoque fuselage can take a fair amount of damage and still hold together. What gives it that ability?
FAA-H-8083-31B, ch. 1, p. 1-9
- AIts skin is thick enough to carry every load by itself, so the frames inside can fail safely
- BIts loads are shared by frames, stringers, longerons and skin, so no one part is critical
- CA welded steel tube truss inside it carries the loads, so the skin can be damaged freely
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Its loads are shared by frames, stringers, longerons and skin, so no one part is critical
In semimonocoque construction, bulkheads, frames and formers give the shape, longerons and stringers reinforce the skin, and the skin itself carries part of the load. Because the loads are spread across all of these parts, no single piece is failure critical, so the fuselage can lose some of them and still hold together. With no other bracing, a true monocoque puts the primary stresses on the skin alone, and a truss puts the loads on a framework of tubes.
- Q.02
A patch is going onto thin skin, but the rivets on hand are much larger in diameter than that skin calls for. What is driving them properly likely to do?
FAA-H-8083-31B, ch. 4, p. 4-31
- ALeave the rivets loose, since a thick shank cannot fill its hole
- BPull the patch tight enough that no sealant is ever needed
- CBulge the thin skin around each rivet head as they are driven
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Bulge the thin skin around each rivet head as they are driven
The diameter of a rivet should be matched in general to the thickness of the material it joins. Driving a rivet that is too large for thin sheet takes so much force that the sheet bulges around the rivet head, which is why thin skin gets a smaller rivet. The hole is drilled to suit the rivet, so a larger shank still fills it, and rivets alone do not make a joint airtight or watertight.
- Q.03
A multiple disc brake is off the airplane for inspection. One stationary disc has no cracks and its key slots are within limits, but its wear pads are worn past their limit. What can be done?
FAA-H-8083-31B, ch. 13, p. 13-70
- AReject the disc, since pads worn past limits condemn it
- BReplace the worn pads and keep the disc in service
- CTurn the disc over so its less worn side faces the rotor
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Replace the worn pads and keep the disc in service
Pads worn beyond their limits may be replaced as long as the stationary disc they mount on passes its own inspection, which looks for cracks and for key slots worn wider than the maintenance manual allows. Worn pads do not condemn a sound disc. Turning the disc over is no fix, since the pads themselves are worn out, and the manufacturer's procedure governs how the pads are replaced.
- Q.04
You are adding the failure warning wiring for a system that is critical to flight safety. The system's operating wires run through connector P1, which has spare contacts. Where should the warning wires go?
FAA-H-8083-31B, ch. 9, p. 9-94
- AThrough a different connector, so one connector fault cannot take out both
- BInto the spare contacts in P1, since spares are kept there for added wiring
- CInto P1 beside the operating pins, so a fault in P1 sets off the warning
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Through a different connector, so one connector fault cannot take out both
On a system critical to flight safety, the wires that operate the system should go through a different connector from the wires for its failure warning. That way one connector failure cannot stop the system and also silence the warning meant to tell the crew it has stopped. Spare contacts are left in a connector for wiring added later, but that does not make P1 the place for these wires. With the warning in P1, a fault in P1 can take the warning out along with the system, so it may never come on.
- Q.05
In a roller-type freewheeling unit in a helicopter drive, inclined surfaces force rollers against an outer drum while the engine drives the rotor. What happens if the engine fails?
FAA-H-8083-31B, ch. 2, p. 2-36
- AThe rollers lock tighter, and the engine drags the rotor down
- BA shear pin breaks and has to be replaced before the next flight
- CThe rollers move inward and let the outer drum overrun the inner part
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
The rollers move inward and let the outer drum overrun the inner part
The freewheeling unit is the clutch that lets the main rotor keep turning when the engine stops. While the engine drives, inclined surfaces wedge the rollers against the outer drum, and the 2 turn together. If the engine fails, the rollers move inward and the outer drum is free to run faster than the inner part, so the transmission turns faster than the dead engine and the helicopter can autorotate instead of having its rotor dragged down. No shear pin is involved.
- Q.06
Many reciprocating-engine tachometers have small numeric drums geared to the mechanism inside them. What do those drums keep track of?
FAA-H-8083-31B, ch. 10, p. 10-28
- AThe time the engine has been operated, as an hour meter
- BThe highest rpm the engine has reached since the last reset
- CThe number of engine starts since the last overhaul
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
The time the engine has been operated, as an hour meter
Those numeric drums are an hour meter. They are geared to the tachometer's rotating mechanism, so they move only while the engine turns and keep a running total of the time the engine has been operated. They hold no record of peak rpm or of how many starts the engine has made: the pointer shows rpm as it happens, and nothing in the drums counts starts.
- Q.07
A mechanic often gets phosphate ester hydraulic fluid on his bare hands and leaves it there until the end of the shift. What can that lead to?
FAA-H-8083-31B, ch. 12, p. 12-5
- ANothing, since these fluids condition the skin rather than harm it
- BDry skin that can turn into dermatitis or a bacterial infection
- CAn allergic rash that shows up within minutes of each contact
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Dry skin that can turn into dermatitis or a bacterial infection
Phosphate ester fluids are good solvents and dissolve away some of the fatty materials of the skin. Repeated or prolonged contact can dry the skin out, and left unattended that can lead to dermatitis or even a bacterial infection. They can make the skin itch, but they are not known to cause allergic rashes. The answer is proper gloves and eye protection whenever any hydraulic fluid is handled.
- Q.08
The fuel quantity gauges on a transport are out of service, and you have to find how much fuel is in a wing tank from its drip sticks. How do you get the figure?
FAA-H-8083-31B, ch. 14, p. 14-39
- ALower each stick until fuel drips out, add every reading, and use the maker's chart
- BRead only the stick nearest mid-tank and multiply it by the number of sticks
- CPush each stick up to the top of the tank and read the wet mark left on it
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Lower each stick until fuel drips out, add every reading, and use the maker's chart
Drip sticks are lowered from the bottom of the tank. Each one is pushed and turned to release it, then let down until fuel starts to come out of the hole in its bottom end, and its scale is read at that point. The readings of all the sticks in the tank are added and turned into pounds or gallons with the manufacturer's chart. One stick cannot stand for the whole tank, and a drip stick is not read like a dipstick, by a wet mark.
- Q.09
You need to hold a finished aluminum part in a bench vise while you file one edge of it. How do you keep the vise jaws from marking the part?
FAA-H-8083-31B, ch. 4, p. 4-28
- AFit padding, such as a ready-made rubber jaw pad, over the jaws
- BClamp it as lightly as you can so the jaws barely touch it
- CUse the utility vise, whose scored jaws grip without marking
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Fit padding, such as a ready-made rubber jaw pad, over the jaws
Bare vise jaws can mar a finished part, so some kind of padding goes over them, such as a ready-made rubber jaw pad. Clamping very lightly is no answer, since the part can then shift while it is being worked. The utility bench vise has scored, removable jaws, which bite into soft metal rather than protect it, and even the flat jaws of a machinist's vise are padded when the finish matters.
- Q.10
Besides traffic in the air, what other hazard does ADS-B extend collision avoidance to cover?
FAA-H-8083-31B, ch. 11, p. 11-58
- AWake turbulence trailing behind heavy airplanes on final approach
- BRunway incursions by aircraft and vehicles on the airport surface
- CTerrain rising ahead of the airplane while it is in cloud
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Runway incursions by aircraft and vehicles on the airport surface
ADS-B gives aircraft a far fuller picture of the traffic around them, and its collision avoidance is expanded to include runway incursions by other aircraft and by support vehicles on the surface of an airport. That is one of the features ADS-B IN offers that TCAS does not. Wake turbulence and rising terrain are not what this collision avoidance watches for.
- Q.11
You are looking over a used inner tube before it goes back into a tube-type tire. Where on the tube is the tire bead most likely to have worn it?
FAA-H-8083-31B, ch. 13, p. 13-87
- AAround its inside diameter, where the toe of the bead bears on it
- BAcross its outer crown, under the middle of the tread
- CAt the valve stem, where it passes out through the wheel
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Around its inside diameter, where the toe of the bead bears on it
The bead of a tire sits down at the wheel rim, so the part of a tube it can wear is the tube's inside diameter, where the toe of the bead bears on it. That area is looked at along with the usual checks for leaks, creases and thin, chafed spots, and a tube chafed thin is discarded. The crown under the tread and the valve stem are not where the bead touches the tube.
- Q.12
Before swaging a terminal onto a control cable, you push the cable about 1 inch into the barrel, bend it slightly toward the terminal, then push it fully home. What is the bend for?
FAA-H-8083-31B, ch. 2, p. 2-40
- AIt marks the insertion depth so any slipping shows up after swaging
- BIts kink gives enough friction to hold the terminal on until it is swaged
- CIt spreads the strands so the barrel grips each wire on its own
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Its kink gives enough friction to hold the terminal on until it is swaged
Pushing the cable in about an inch and bending it toward the terminal puts a slight kink in the cable end. Once the end is pushed all the way in, that kink gives enough friction to keep the terminal in place until the swaging is done. The insertion depth is marked separately, with masking tape on the cable, which is what shows whether it slipped, and nothing in the procedure spreads the strands apart.
- Q.13
A repair calls for a laminate that is not symmetrical, and you want it to come out with as little warping as possible. Which cure will distort it least?
FAA-H-8083-31B, ch. 7, p. 7-29
- AAn autoclave cure at high temperature and pressure
- BAn oven cure with the heat spread evenly
- CA wet layup cured at room temperature
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
A wet layup cured at room temperature
A laminate that is not symmetrical tends to warp, and the effect is worst when it is cured at high temperature in an autoclave or oven, because of the thermal stresses set up as it cools from cure temperature to room temperature. A typical wet layup cured at room temperature shows much less distortion, since its thermal stresses are much smaller. Spreading the oven heat evenly does not remove those cool-down stresses.
- Q.14
Behind a radio rack you find a small washer lying across the terminal strip that joins the radios to the aircraft electrical system. Why does that matter?
FAA-H-8083-31B, ch. 9, p. 9-90
- AIt does not, as long as every connection on the strip is tight
- BIt can only cause noise in the radios, never damage
- CIt can cause arcing that may lead to a fire or system failure
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
It can cause arcing that may lead to a fire or system failure
Terminal strips that tie radio and electronic systems into the aircraft electrical system are inspected for loose connections, for metal objects that may have fallen across them, and for dirt and grease. Any of these can cause arcing, which may result in a fire or system failures. Tight connections do not make a stray washer safe, and the risk is far more than noise in the radios.
- Q.15
During a walkaround with the pitot heat switched on, a new mechanic reaches out to feel whether the pitot tube is warming up. What is wrong with that check?
FAA-H-8083-31B, ch. 10, p. 10-13
- AThe mechanic could take a shock from a bare heater element at the tip
- BThe tube will feel cold, since its heater only works with air flowing past
- CThe heater can make the tube hot enough to burn the hand that touches it
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
The heater can make the tube hot enough to burn the hand that touches it
Many pitot tubes carry an electric heating element so that ice cannot block them, and it makes the tube too hot to touch without getting burned. It gets that hot on the ground too, because it is sized to keep ice off at altitude in very cold air at high speed, so the safe check is to watch the heater's current on an ammeter or load meter. The element is inside the tube, not bare at the tip.
We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.
The FAA A&P Airframe subjects, one page each
Each subject page has its own questions, written from the FAA’s own documents, with how much of the test it is and what the FAA says people miss most.
- Aircraft Structures1 of the questions above · FAA-H-8083-31B chapter 1
- Aerodynamics, Assembly and Rigging2 of the questions above · FAA-H-8083-31B chapter 2
- Aircraft Fabric CoveringFAA-H-8083-31B chapter 3
- Aircraft Metal Structural Repair2 of the questions above · FAA-H-8083-31B chapter 4
- Aircraft WeldingFAA-H-8083-31B chapter 5
- Aircraft Wood Structural RepairFAA-H-8083-31B chapter 6
- Advanced Composite Materials1 of the questions above · FAA-H-8083-31B chapter 7
- Aircraft Painting and FinishingFAA-H-8083-31B chapter 8
- Aircraft Electrical Systems2 of the questions above · FAA-H-8083-31B chapter 9
- Aircraft Instrument Systems2 of the questions above · FAA-H-8083-31B chapter 10
- Communication and Navigation Systems1 of the questions above · FAA-H-8083-31B chapter 11
- Hydraulic and Pneumatic Power Systems1 of the questions above · FAA-H-8083-31B chapter 12
- Aircraft Landing Gear Systems2 of the questions above · FAA-H-8083-31B chapter 13
- Aircraft Fuel Systems1 of the questions above · FAA-H-8083-31B chapter 14
- Ice and Rain ProtectionFAA-H-8083-31B chapter 15
- Cabin Environmental Control SystemsFAA-H-8083-31B chapter 16
- Fire Protection SystemsFAA-H-8083-31B chapter 17
- Airframe InspectionFAA-H-8083-31B chapter 2
- Water and Waste SystemsAC 25.1455-1
About these practice questions
Q.01Are these real FAA A&P Airframe test questions?
No. We wrote them for this page from FAA-H-8083-31B, the FAA’s Airframe handbook, and each one names the page it was written from so you can check it. They are not FAA test questions, and none of them comes from our question bank.
Q.02How should I use these FAA A&P Airframe practice questions?
Answer each one before you open it, and note the ones you miss. A miss points at a subject, and each subject has its own page below, with more questions on it and how much of the Airframe test it is.
Q.03How many questions are on the FAA A&P Airframe test?
100, in 2 hours, with 70% to pass. Everything else about the test is on the FAA A&P Airframe written test page.
Q.04Where can I practice more FAA A&P Airframe questions?
Our bank holds 5,614 Airframe questions across 19 subjects, each with a written explanation. A free account gives you one free set, 25 questions and 25 fill-in-the-gaps from any subject you pick, once, and Pro opens the rest.
FREE PLAN · NO CARD · 25 QUESTIONS TO START
The bank holds 5,614 FAA A&P Airframe questions.
Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.
Start freeOr answer a few first. The free FAA A&P practice test runs on the page, with no account.