AMA · AF-10 · FAA-H-8083-31B CH. 10
FAA A&P Airframe: Aircraft Instrument Systems
For the FAA A&P Airframe test, aircraft instrument systems is chapter 10 of FAA-H-8083-31B, Aircraft Systems. Its ACS subject area, Aircraft Instrument Systems, is 5 to 10% of the test, or 5 to 10 of its 100 scored questions. Our question bank holds 374 questions on it, and the 10 below were written for this page.
Test shares and most-missed codes read from the FAA on 15 November 2026.
What FAA-H-8083-31B chapter 10 covers
Chapter 10 is headed Aircraft Systems, and it is the instruments chapter. It covers the pressure instruments built on Bourdon tubes, diaphragms and aneroids, from the altimeter, airspeed indicator and vertical speed indicator to the manifold pressure gauge, and the pitot-static system that feeds them.
It also covers temperature, rpm and fuel quantity indication, synchro systems, the gyroscopic instruments and the magnetic compass, electronic flight displays, autopilots, and installing and marking instruments.
It runs from pages 10-1 to 10-84 of the Aviation Maintenance Technician Handbook: Airframe, which the FAA publishes free as a PDF.
How much of the FAA A&P Airframe test it is
- 5 to 10%OF THE TESTACS area AM.II.H
- 5 to 10QUESTIONSof 100 scored
- 374IN OUR BANKquestions on this subject
The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Aircraft Instrument Systems (AM.II.H) is 5 to 10% (5 to 10 questions) on the 100-question Airframe test. The 15 ranges for the Airframe test add up to anywhere from 75% to 160%, so they say how big an area can get, not how many questions you will see from it.
No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.
Aircraft instrument systems questions and answers
10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.
- Q.01
A fuel pressure gauge gives the pilot critical information. Which of these conditions is it there to catch?
FAA-H-8083-31B, ch. 10, p. 10-9
- AWater that has settled out at the bottom of a fuel tank's sump
- BA failing pump, or a tank run too low to keep the pump fed
- CThe wrong grade of fuel loaded at the last refueling
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
A failing pump, or a tank run too low to keep the pump fed
Fuel is pumped from the tanks to the engines, and the gauge shows whether it is arriving at the pressure it should. A malfunctioning pump, or a tank emptied so far that too little fuel enters the pump for it to hold its output pressure, shows up as low pressure and needs the pilot's attention at once. A pressure reading says nothing about water lying in a sump or about which grade of fuel went in at the last refueling.
- Q.02
Before flight, a heading indicator is set to agree with the magnetic compass. Why is it the instrument the pilot then steers by, rather than the compass?
FAA-H-8083-31B, ch. 10, p. 10-56
- AIt shows true heading, so no variation has to be applied
- BIt never drifts, so it needs no resetting once in flight
- CThe compass swings about too much, and the gyro holds steady
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
The compass swings about too much, and the gyro holds steady
A magnetic compass fluctuates a great deal in flight, so a gyro aligned with the compass gives a much more stable heading to fly by. Because it is set from the compass, it shows magnetic heading, not true. It is not free of drift either: precession makes a conventional directional gyro wander from the magnetic reference, so it is realigned with the compass from time to time.
- Q.03
A light airplane's attitude and heading gyros run on suction from an external venturi. Flying through freezing rain, both start to wander. What is the likely cause?
FAA-H-8083-31B, ch. 10, p. 10-46
- AIce building on the venturi and cutting the airflow through it
- BIce over the static ports, which the gyros use as their reference
- CThe pitot heater drawing current away from the gyro motors
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Ice building on the venturi and cutting the airflow through it
A venturi makes its suction only from the air rushing through it, and ice that forms on the venturi tube can hamper that airflow. Less suction means the gyros slow down and stop giving a reliable indication. Air-driven gyros take no reference from the static ports, and they have no electric motors for a pitot heater to rob.
- Q.04
You are about to swing the compass on a light airplane, and the baggage compartment still holds a toolbox and a tow bar from the last job. What should be done about them?
FAA-H-8083-31B, ch. 10, p. 10-82
- ALeave them in, since the swing is done with the airplane as it is normally loaded
- BTake them out, since loose items like these can disturb the compass
- CMove them onto the rear seat, so they sit farther from the panel
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Take them out, since loose items like these can disturb the compass
The compass is swung with the airplane set up as it flies: level flight attitude, normal equipment aboard and switched on, engine running. Loose items that are not part of the airplane, such as tools and a steel tow bar, can pull the compass, so the interior and the baggage compartments are cleared of them first. Leaving them in, or moving them to a seat, still leaves them inside the airplane near the compass.
- Q.05
A newly fitted mechanical tachometer reads nothing, and its flexible drive has been forced into a sharp bend to fit behind the panel. What should be corrected?
FAA-H-8083-31B, ch. 10, p. 10-82
- AClamp the drive tighter at the bend so it cannot whip
- BReplace the indicator, since a drive cannot stop it reading
- CReroute the drive with no sharp bends and no strain on the instrument
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Reroute the drive with no sharp bends and no strain on the instrument
When a mechanical indicator goes in, the flexible drive needs room behind the panel, and any bends must not strain the instrument once it is secured. Sharp bends are to be avoided, because an improperly installed drive can make the indicator fail to read or read wrongly. Securing the drive at frequent intervals stops it whipping, which shows up as pointer oscillation rather than no reading, and there is no reason to blame the indicator before the drive is put right.
- Q.06
An external venturi that drives the gyros on a light airplane is designed to produce its desired suction at about what flight condition?
FAA-H-8083-31B, ch. 10, p. 10-46
- AAbout 100 mph at standard sea level conditions
- BFull power on the ground, before the takeoff roll
- CHigh cruise speed at the airplane's service ceiling
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
About 100 mph at standard sea level conditions
A gyro venturi is sized to give the desired vacuum at roughly 100 mph in standard sea level air. Its suction comes only from flight airflow, so it does not bring the gyros up to speed before takeoff and cannot be checked on the ground, and large changes in airspeed or air density make the suction it gives fluctuate.
- Q.07
Just after start, with the engine settled at idle, the pointer of an electric tachometer drifts about and shows less than it should. What should you do before calling it faulty?
FAA-H-8083-31B, ch. 10, p. 10-81
- AReplace the tach generator, since its output has dropped
- BReset the pointer on its shaft to match the idle rpm
- CBring the rpm up and check that the reading steadies
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Bring the rpm up and check that the reading steadies
At idle, an electric tachometer's synchronous motor may not yet be in step with the generator output, so the pointer can waver and read low. As engine speed comes up, the motor should synchronize and show the rpm correctly. Only if the pointer still swings above that speed do you check the total oscillation against the allowed tolerance. Replacing the generator or moving the pointer would be fixing a fault that is not there.
- Q.08
You are painting approved range markings onto the cover glass of a replacement oil pressure gauge. What else should you add?
FAA-H-8083-31B, ch. 10, p. 10-79
- AA red radial line at the bottom of the scale for zero pressure
- BA white slippage mark running from the glass onto the case
- CA clear lacquer coat so the paint cannot rub off the glass
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
A white slippage mark running from the glass onto the case
Range marks on the cover glass are only right while the glass stays put. A white slippage mark is painted from the glass onto the instrument case, so if the glass turns in the bezel, the broken mark shows that the colored ranges no longer line up with the dial. The range marks themselves come only from approved data.
- Q.09
An airplane's mechanical altimeter has given no trouble at all. Why does its pitot-static system still need periodic inspection and testing?
FAA-H-8083-31B, ch. 10, p. 10-20
- AVibration and big temperature swings can cause damage or a leak over time
- BThe aneroid slowly loses its sealed vacuum and has to be pumped down again
- CThe test is what sets the altimeter to the local station pressure
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Vibration and big temperature swings can cause damage or a leak over time
Analog altimeters and the pitot-static system around them live in a hostile environment. Heavy vibration and wide swings of temperature can damage the instruments or open a leak at the tubing connections and fittings, and the result is a faulty instrument. Care at installation is the best prevention, and periodic inspection and testing confirm the system is still sound. The aneroid is not pumped down again, and setting local pressure is the pilot's job with the barometric scale.
- Q.10
You have cleared moisture from a pitot-static system through its own low-point drains, and no line was opened. What must you see to before the job is finished?
FAA-H-8083-31B, ch. 10, p. 10-81
- AA full leak check, since any draining counts as opening the system
- BBlowing shop air in from the ports to push out whatever is left
- CThat every drain is closed and made secure as the procedure requires
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
That every drain is closed and made secure as the procedure requires
A system fitted with low-point drains can be drained without needing a leak check afterward; that check follows when lines are blown through or components are installed. What must not be missed is closing and securing every drain as the approved procedure requires. Air is never blown in from the pitot and static ports: when air is used, the instruments are disconnected and it is blown from the instrument end toward the ports.
We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.
How a missed code comes back at the oral
Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.II.H. The examiner reads those codes before your oral and practical.
The Airframe oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Airframe also carries 11 practical projects, each with 2 questions attached.
Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.
Questions people ask about aircraft instrument systems
Q.01What are the 2 properties of a gyroscope?
Rigidity in space, which keeps the rotor of a free gyro pointing the same way however its base is turned, and precession, which makes it respond to a force as though the force were applied 90 degrees further around in the direction of rotation. The turn and bank instrument uses precession.
Q.02What does a Bourdon tube measure?
Pressure, and relatively high pressure at that. It is a curved tube fixed at its open end and sealed at the other, which is free to move: as pressure rises the tube tries to straighten, and that movement drives the pointer. Most are brass, bronze or copper.
Q.03What do the colored marks on an instrument mean?
Red marks maximum and minimum limits, beyond which operation is dangerous. Green marks the normal operating range and yellow means caution. Blue and white are used on airspeed indicators for particular conditions, such as the flap operating range.
Q.04What is compass deviation?
Error in a magnetic compass caused by magnetic fields from the aircraft itself, from its metal parts and electrical equipment. Compensating screws move small magnets in the case to reduce it, the process is called swinging the compass, and the results go on a compass correction card near the compass.
Q.05How many aircraft instrument systems questions are on the FAA A&P Airframe test?
The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Aircraft Instrument Systems subject area 5 to 10% of the Airframe test, which is 5 to 10 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.
Q.06Which FAA handbook chapter covers aircraft instrument systems?
Chapter 10 of FAA-H-8083-31B, the Aviation Maintenance Technician Handbook: Airframe, titled "Aircraft Systems". It runs from pages 10-1 to 10-84, and the FAA publishes the whole handbook free as a PDF.
Read the documents, not us
Every fact on this page was read from these on 19 August 2026 and 15 November 2026. They are the authority and we are the summary. If we and one of them disagree, they are right.
- FAA-H-8083-31B, Aviation Maintenance Technician Handbook: Airframe, chapter 10www.faa.gov
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standardswww.faa.gov
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards: the written test blueprints (pages 13 and 14) and chapters 6 and 7www.faa.gov
- FAA, Frequently Missed Knowledge Test ACS Codes, 2nd Quarter CY25www.faa.gov
More FAA A&P Airframe subjects
FREE PLAN · NO CARD · 25 QUESTIONS TO START
The bank holds 374 aircraft instrument systems questions.
Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.
Start freeOr answer a few first. The free FAA A&P practice test runs on the page, with no account.