AMA · AF-15 · FAA-H-8083-31B CH. 15
FAA A&P Airframe: Ice and Rain Protection
For the FAA A&P Airframe test, aircraft ice and rain protection is chapter 15 of FAA-H-8083-31B, Ice & Rain Protection. Its ACS subject area, Ice and Rain Control Systems, is 5 to 10% of the test, or 5 to 10 of its 100 scored questions. Our question bank holds 212 questions on it, and the 10 below were written for this page.
Test shares and most-missed codes read from the FAA on 15 November 2026.
What FAA-H-8083-31B chapter 15 covers
Chapter 15 starts with how ice forms on an aircraft, clear and rime, and the difference between anti-icing and deicing. It covers the systems: pneumatic deice boots, thermal anti-ice with hot bleed air or electric heat, chemical systems such as TKS, and propeller and windshield ice protection.
It also covers deicing aircraft on the ground with fluids, rain control by wipers, chemical repellent, hydrophobic coatings and air, and keeping water and waste lines from freezing.
It runs from pages 15-1 to 15-31 of the Aviation Maintenance Technician Handbook: Airframe, which the FAA publishes free as a PDF.
How much of the FAA A&P Airframe test it is
- 5 to 10%OF THE TESTACS area AM.II.L
- 5 to 10QUESTIONSof 100 scored
- 212IN OUR BANKquestions on this subject
The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Ice and Rain Control Systems (AM.II.L) is 5 to 10% (5 to 10 questions) on the 100-question Airframe test. The 15 ranges for the Airframe test add up to anywhere from 75% to 160%, so they say how big an area can get, not how many questions you will see from it.
No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.
Aircraft ice and rain protection questions and answers
10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.
- Q.01
In a heated airliner windshield, what is the point of mounting the heating wires or film just behind the outermost glass, not deeper in the laminate?
FAA-H-8083-31B, ch. 15, p. 15-28
- ASo the elements warm the cabin air behind the windshield first
- BSo enough heat reaches the outside of the windshield, where ice forms
- CSo the elements can be replaced without taking the windshield apart
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
So enough heat reaches the outside of the windshield, where ice forms
The laminated construction lets heating elements, either resistance wires or a transparent conductive ply, be built into the glass layers to keep the windshield clear of ice, frost and fog. To make sure enough heat is applied to the outside of the windshield, the elements are placed on the inside of the outer glass ply. The plies are bonded together with heat and pressure, and the aim is the outer surface, not the cabin air.
- Q.02
During ground deicing, which parts does the handbook give as examples where hot air may be needed instead of the usual fluid spray?
FAA-H-8083-31B, ch. 15, p. 15-24
- AThe landing gear and the propellers
- BThe wing upper surfaces and the stabilizers
- CThe flight deck windows and the cabin windows
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
The landing gear and the propellers
Every surface with an aerodynamic, control, sensing, movement or measuring function must be clean, but not all of them can be deiced the way the wings are. The handbook notes that hot air may be required when deicing the landing gear or propellers, and fluid is not sprayed directly onto brakes, wheels, exhausts or thrust reversers. Wings and stabilizers take the normal fluid spray, while fluid is kept off the flight deck and cabin windows.
- Q.03
An airliner parks after a long flight at high altitude. The day is above freezing, yet frost forms on the wing skin over the integral fuel tanks. What explains it?
FAA-H-8083-31B, ch. 15, p. 15-23
- AFuel seeping from the tank seams is freezing on the skin
- BLeftover deicing fluid from the morning has refrozen there
- CThe fuel is still very cold from altitude and chills the tank skin
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
The fuel is still very cold from altitude and chills the tank skin
Ice on a parked aircraft can come from direct precipitation, from frost forming on integral fuel tanks after prolonged flight at high altitude, or from snow and slush picked up while taxiing. After hours at altitude the fuel left in the wing can still be well below freezing, and it chills the skin over the tanks, so frost can form there on a day above freezing. Jet fuel does not freeze on a mild day, and deicing fluid is made to stop frost, not to cause it.
- Q.04
Inspecting a wing anti-ice duct, you find a small hole burned through its insulating lagging. What could that be telling you?
FAA-H-8083-31B, ch. 15, p. 15-5
- AHot air may be leaking from the duct beneath it
- BNothing, since holes in lagging are normal vent openings
- CThe piccolo tube is blocked, so the duct is running cold
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Hot air may be leaking from the duct beneath it
Leak checks on anti-ice ducting look for defects that would let heated air escape. Air leaks can often be heard, and they are sometimes revealed by holes in the lagging or thermal insulation, so a burned hole points to the duct under it. If a leak is hard to find, a soap and water solution can be used. Lagging has no vent openings, and a duct running cold would not burn its insulation.
- Q.05
At a scheduled inspection you find fine weather cracks in the rubber surface of a wing deicer boot. What should you put on it?
FAA-H-8083-31B, ch. 15, p. 15-21
- AA thin film of silicone grease to seal it
- BA coat of conductive cement over the boot
- CA coat of clear lacquer to keep out the sun
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
A coat of conductive cement over the boot
Weather cracking on a deicer boot is treated with a coating of conductive cement. It seals the boot against the weather and keeps the surface able to dissipate static, so the charge does not puncture the boot by arcing to the metal beneath. Grease, oil and similar substances deteriorate deicer rubber and are kept off the boots.
- Q.06
The pressure relief valve in a pneumatic deice boot system has to be reset. How is that adjustment made?
FAA-H-8083-31B, ch. 15, p. 15-20
- AWith the engines off, by setting it so the suction gauge reads 4.5 to 5.5 in. Hg
- BOn the bench, by setting it to open at the normal boot inflation pressure
- CWith the engines running, turning its screw until the gauge shows the relief pressure
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
With the engines running, turning its screw until the gauge shows the relief pressure
A pressure relief valve is a safety device that relieves excess pressure if the regulator valve fails. To adjust it, the aircraft engines are operated and a screw on the valve is turned until the deicing pressure gauge shows the specified pressure at which the valve should relieve. The 4.5 to 5.5 in. Hg reading is suction, set at the vacuum relief valve, and a relief valve set to open at normal inflation pressure would dump the air the boots need.
- Q.07
A twin's electrothermal propeller deice timer works through 4 element groups for 30 seconds each: right prop outer, then right inner, then left outer, then left inner, and repeats. After the right prop's outer elements switch off, how long until they come on again?
FAA-H-8083-31B, ch. 15, p. 15-23
- A60 seconds
- B90 seconds
- C120 seconds
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
90 seconds
Each of the 4 element groups is heated for 30 seconds in turn, and the timer cycles continuously. Once the right outer elements switch off, the other 3 groups take their turns first, so 3 times 30 gives 90 seconds before the right outer elements heat again. 120 seconds is the whole cycle, which counts the right outer group's own 30 seconds, and 60 seconds leaves one group out.
- Q.08
A shop looks after 2 light twins that both have TKS weeping-wing ice protection. What can you say about flying them into known icing conditions?
FAA-H-8083-31B, ch. 15, p. 15-11
- ACheck each: some are certified for it, others only carry it as a hedge
- BThey both may, since every weeping-wing system is certified for it
- CNot at all, since no weeping-wing system is ever approved for it
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Check each: some are certified for it, others only carry it as a hedge
Weeping-wing systems are basically the same from one aircraft to another, but some aircraft that have them are certified to fly into known icing conditions, while others use the system only as a hedge against unexpected ice met in flight. So the approval comes from each airplane's certification, not from the system itself, and each one has to be checked. The reservoir allows about 1 to 2 hours of operation.
- Q.09
Pitot heat is being checked with the airplane parked on the ramp. Why does that check call for caution?
FAA-H-8083-31B, ch. 15, p. 15-9
- AIts heater switches to a higher setting whenever the airplane is on the ground
- BIts heat is meant only to dry the tube after washing, so it runs hot
- CIt must keep ice off at about -50 °F and 500 mph, so it gets extremely hot
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
It must keep ice off at about -50 °F and 500 mph, so it gets extremely hot
A pitot tube heater is sized to keep ice from forming at altitude, in temperatures near -50 °F and at speeds that may be over 500 miles per hour. Parked on the ground, with no cold airflow over it, the tube gets extremely hot, which is why its function check calls for caution, and an ammeter or load meter in the circuit is the safe way to see that it works. The heat comes from what the tube has to do in flight, not from any setting that turns it up on the ground, and it is there for ice, not for drying.
- Q.10
The final application of anti-icing fluid starts at 10:05 and ends at 10:12. The holdover time for the conditions is 40 minutes. The airplane reaches the runway at 10:32. How many minutes of holdover time are left?
FAA-H-8083-31B, ch. 15, p. 15-24
- A13 minutes
- B20 minutes
- C27 minutes
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
13 minutes
Holdover time starts when the final application of fluid begins, not when it ends. From 10:05 to 10:32 is 27 minutes, and 40 minus 27 leaves 13 minutes. Counting from 10:12 gives 20 minutes, which overstates the protection left, and 27 minutes is the time already used up.
We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.
How a missed code comes back at the oral
Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.II.L. The examiner reads those codes before your oral and practical.
The Airframe oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Airframe also carries 11 practical projects, each with 2 questions attached.
Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.
Questions people ask about aircraft ice and rain protection
Q.01What is the difference between clear ice and rime ice?
Clear ice forms from large drops that flow over the surface before they freeze, and it is hard, heavy and difficult to remove. Rime ice forms from small drops that freeze as they hit, trapping air, so it is white, lighter and brittle, but its rough shape still spoils the airfoil.
Q.02What is the difference between anti-icing and deicing?
Anti-icing stops ice from forming, by heating a surface or wetting it with fluid. Deicing lets ice build up and then removes it, as pneumatic boots do when they inflate and crack it away.
Q.03Why should rain repellent not be used on a dry windshield?
Undiluted repellent restricts visibility through the windshield, and its residue can stain or slightly corrode the skin. It is for very wet conditions. If it goes on by mistake, the wipers are not run, and the residue is rinsed off with fresh water.
Q.04How are pneumatic deice boots looked after?
They are cleaned with mild soap and water when the aircraft is washed, kept free of fuel, oil, grease and dirt, and resurfaced with conductive cement once wear has destroyed the electrical conductivity of the surface. Small damage can be cold patched once the boot is relieved of its tension.
Q.05How many aircraft ice and rain protection questions are on the FAA A&P Airframe test?
The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Ice and Rain Control Systems subject area 5 to 10% of the Airframe test, which is 5 to 10 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.
Q.06Which FAA handbook chapter covers aircraft ice and rain protection?
Chapter 15 of FAA-H-8083-31B, the Aviation Maintenance Technician Handbook: Airframe, titled "Ice & Rain Protection". It runs from pages 15-1 to 15-31, and the FAA publishes the whole handbook free as a PDF.
Read the documents, not us
Every fact on this page was read from these on 19 August 2026 and 15 November 2026. They are the authority and we are the summary. If we and one of them disagree, they are right.
- FAA-H-8083-31B, Aviation Maintenance Technician Handbook: Airframe, chapter 15www.faa.gov
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standardswww.faa.gov
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards: the written test blueprints (pages 13 and 14) and chapters 6 and 7www.faa.gov
- FAA, Frequently Missed Knowledge Test ACS Codes, 2nd Quarter CY25www.faa.gov
FREE PLAN · NO CARD · 25 QUESTIONS TO START
The bank holds 212 aircraft ice and rain protection questions.
Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.
Start freeOr answer a few first. The free FAA A&P practice test runs on the page, with no account.