AMA · AF-14 · FAA-H-8083-31B CH. 14
FAA A&P Airframe: Aircraft Fuel Systems
For the FAA A&P Airframe test, aircraft fuel systems is chapter 14 of FAA-H-8083-31B, Aircraft Fuel Systems. Its ACS subject area, Aircraft Fuel Systems, is 5 to 10% of the test, or 5 to 10 of its 100 scored questions. Our question bank holds 320 questions on it, and the 10 below were written for this page.
Test shares and most-missed codes read from the FAA on 15 November 2026.
What FAA-H-8083-31B chapter 14 covers
Chapter 14 covers the requirements a fuel system has to meet, the fuels and their problems, detonation, vapor lock and contamination, and the kinds of system, from the gravity feed of a light airplane to the pump fed systems of a transport.
It covers the components (tanks, integral, rigid and bladder; lines and fittings; valves, pumps, strainers and heaters; quantity indicating systems), fueling and defueling, fuel jettison, finding and classifying leaks, repairing tanks, and fire safety during fuel work.
It runs from pages 14-1 to 14-57 of the Aviation Maintenance Technician Handbook: Airframe, which the FAA publishes free as a PDF.
How much of the FAA A&P Airframe test it is
- 5 to 10%OF THE TESTACS area AM.II.J
- 5 to 10QUESTIONSof 100 scored
- 320IN OUR BANKquestions on this subject
The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Aircraft Fuel Systems (AM.II.J) is 5 to 10% (5 to 10 questions) on the 100-question Airframe test. The 15 ranges for the Airframe test add up to anywhere from 75% to 160%, so they say how big an area can get, not how many questions you will see from it.
No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.
Aircraft fuel systems questions and answers
10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.
- Q.01
Which of these operating conditions does the handbook list among the causes of detonation in a reciprocating engine?
FAA-H-8083-31B, ch. 14, p. 14-5
- ARunning at high rpm while the airspeed is low
- BIdling on the ramp with the mixture set full rich
- CCruising at low power after the engine has cooled down
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Running at high rpm while the airspeed is low
The handbook lists incorrect fuel, an engine already hot at a high power setting such as takeoff, preignition, long operation with an extremely lean mixture, and operation at high rpm with low airspeed as causes of detonation. Idling on the ramp with a rich mixture and cruising at low power with a cooled engine are not on that list. Detonation shows as a rise in cylinder head temperature and, left alone, can lead to engine failure.
- Q.02
How does the amount of solid particle contamination a turbine engine fuel system can tolerate compare with a reciprocating engine fuel system?
FAA-H-8083-31B, ch. 14, p. 14-51
- AIt is about the same, since both use the same kind of strainers
- BIt is greater, since jet fuel holds particles in suspension longer anyway
- CIt is much less, since turbine fuel controls are close-tolerance units
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
It is much less, since turbine fuel controls are close-tolerance units
The maximum amount of solid particle contamination allowable is much less in a turbine engine fuel system than in a reciprocating engine system. Turbine fuel control units are extremely close-tolerance devices, which is why micronic filters are used to keep the fuel delivered to them clean. Particles staying suspended longer in jet fuel makes them harder to get rid of, not more acceptable, and the 2 systems do not share one tolerance.
- Q.03
Why is draining the sumps not enough on its own to keep the fuel clean for a turbine engine's fuel control?
FAA-H-8083-31B, ch. 14, p. 14-49
- AJet fuel holds all its water dissolved, so none reaches a sump
- BParticles stay suspended longer in jet fuel because of its viscosity
- CTurbine fuel systems are built without any sump drains to sample
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Particles stay suspended longer in jet fuel because of its viscosity
Turbine fuel controls are highly refined, and hundreds of pounds of fuel pass through them every hour. Particles stay suspended longer in jet fuel because of its viscosity, so sumping alone does not catch them, and a series of filters is designed into the system to trap foreign matter. Water does settle out of jet fuel, slowly, and turbine aircraft are drained daily through their sumps like any other.
- Q.04
A line worker thinks he may have put a few gallons of jet fuel into the nearly full tanks of a 100LL single. The sump samples still look blue. What should you do?
FAA-H-8083-31B, ch. 14, p. 14-52
- AGround it, since a little jet fuel may not change how the fuel looks
- BRelease it, since blue samples prove the tanks still hold only 100LL
- CRun the engine up on the ramp, and release it if it runs smoothly
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Ground it, since a little jet fuel may not change how the fuel looks
A small quantity of the wrong type of fuel may not look any different when the fuel is checked by eye, which makes the situation more dangerous, so blue samples prove nothing here. Anyone who recognizes that the error has occurred must ground the aircraft until it is put right. Running the engine proves nothing either and makes the job bigger: once an engine has run on the wrong fuel, the whole fuel system is drained and flushed and the engine is inspected.
- Q.05
The manual for a twin warns that a lot of fuel must be drained from one tank's sump before settled water reaches its drain valve. A new hire draws one small cup there, sees clean fuel and signs off. What is wrong with that?
FAA-H-8083-31B, ch. 14, p. 14-50
- ANothing, since settled water always reaches a sump drain first
- BWater collects near the top of the tank, so no sump sample would ever show it
- CA small sample may come out before any settled water reaches the valve
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
A small sample may come out before any settled water reaches the valve
On some aircraft a large amount of fuel has to be drained before settled water reaches the drain valve, and knowing that quirk of a particular aircraft matters. One small cup can come out clean while water still sits in the tank, so enough is drained to be sure the sample gets down to the water. Water is heavier than fuel and settles toward the sump, so it does not collect at the top of the tank.
- Q.06
A transport's capacitance fuel gauge for one tank keeps disagreeing with its drip stick reading, and that tank's sump has been giving up a lot of water. How could these findings be linked?
FAA-H-8083-31B, ch. 14, p. 14-50
- AThey are not linked, since quantity probes sense only the weight of the fuel
- BA large amount of water in the fuel can upset the quantity probe readings
- CWater floats on top of the fuel and pushes the drip stick out of place
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
A large amount of water in the fuel can upset the quantity probe readings
Water that gets into a fuel tank normally sinks to the bottom and into the sump. Settled water can cause corrosion, and high quantities of water in the fuel can also cause discrepancies in fuel quantity probe indications, so a tank that keeps giving up water is a likely reason for a gauge that disagrees with the drip stick. Water is heavier than fuel, so it does not float on top.
- Q.07
A fuel sample from a piston twin turns the gray powder in a water test kit pink, showing more than 30 ppm of water. What should be done about it?
FAA-H-8083-31B, ch. 14, p. 14-52
- ARelease the airplane, since the fuel strainers will hold back the water
- BAdd anti-ice additive so it takes up the water, then release it
- CLet the water settle out, or defuel and refill with good fuel
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Let the water settle out, or defuel and refill with good fuel
Water above the level the kit detects is generally not acceptable or safe for operation. The fuel is either given time for the water to settle out, so it can be drained off, or the aircraft is defueled and refueled with acceptable fuel. Strainers catch water far less well than solid particles, so they are no answer, and anti-ice additive only dissolves in the water and lowers its freezing point, which does not make wet fuel fit to use.
- Q.08
In a field water test, a dye that dissolves in water but not in fuel is added to a fuel sample, and the whole sample turns strongly colored. What does that tell you?
FAA-H-8083-31B, ch. 14, p. 14-52
- AThere is a lot of water in it, since the dye spreads further with more water
- BThere is no water, since the dye has dissolved in the fuel itself
- CThe test is spoiled, because this dye never colors a fuel sample
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
There is a lot of water in it, since the dye spreads further with more water
A common field test for water adds a dye that dissolves in water but not in fuel to a sample drawn from the tank. The more water there is, the more the dye disperses and colors the sample, so a strongly colored sample means a lot of water. A sample with little or no water shows little color, and the dye coloring the sample is exactly how the test is meant to work.
- Q.09
An airline orders its jets with optional long-range auxiliary fuel tanks for ocean crossings. Where are such added tanks usually located?
FAA-H-8083-31B, ch. 14, p. 14-13
- AIn pods hung under each wing outboard of the engines
- BIn the fuselage section of the aircraft
- CIn the engine nacelles behind each firewall
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
In the fuselage section of the aircraft
The same airliner model can be ordered with different fuel storage. Airlines planning transoceanic flights may order long-range auxiliary tanks, and these added tanks are usually located in the fuselage section. They change how the fuel load is managed and make the fuel system more complex. Pods under the wing and tanks in the engine nacelles are not where the handbook puts them.
- Q.10
Over-the-wing fueling is under way, and someone wants to run an electric drill on the same wing a few feet from the open filler. Why should that wait?
FAA-H-8083-31B, ch. 14, p. 14-57
- AFuel vapor spreads well beyond the opening, and one spark can light it
- BThe drill's current can flow back through the nozzle's bonding wire
- CDrill vibration can unseat the nozzle and stop the flow of fuel
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Fuel vapor spreads well beyond the opening, and one spark can light it
Fuel vapor, air and a source of ignition are what a fuel fire needs, and the source of ignition is the one most easily controlled. Fuel vapors spread well beyond the actual tank opening, and a simple spark, even one from static electricity, could be enough to light them, so electrical devices are not operated near an aircraft being fueled. The drill's danger is its sparks, not the bonding wire or the nozzle.
We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.
How a missed code comes back at the oral
Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.II.J. The examiner reads those codes before your oral and practical.
The Airframe oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Airframe also carries 11 practical projects, each with 2 questions attached.
Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.
Questions people ask about aircraft fuel systems
Q.01How are fuel leaks classified?
By the size of the wetted area it makes in 30 minutes. Under 3/4 inch across is a stain, 3/4 to 1 and a half inches is a seep, 1 and a half to 4 inches is a heavy seep, and a running leak pools and drips from the aircraft. The maintenance manual says what has to be repaired before flight.
Q.02What is vapor lock?
Avgas turning to vapor in the lines or other parts between the tank and the carburetor, so that vapor blocks the flow of liquid fuel. Hot fuel, low pressure or too much turbulence in the fuel can cause it, and it happens most on warm days in aircraft whose engine driven pump draws fuel from the tanks.
Q.03What is an integral fuel tank?
Part of the aircraft structure, usually the wing, sealed so that it holds the fuel itself. On transport aircraft much of each wing is an integral tank. The other kinds are rigid removable tanks and bladder tanks.
Q.04Why is water a problem in aviation fuel?
Water can freeze in the fuel system as the fuel cools in a climb, and microbes thrive where water settles under fuel, forming a film that clogs filters, corrodes tank coatings and degrades the fuel. Free water and sediment are drained from the sumps before flight, but water dissolved or carried in the fuel cannot be drained out.
Q.05How many aircraft fuel systems questions are on the FAA A&P Airframe test?
The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Aircraft Fuel Systems subject area 5 to 10% of the Airframe test, which is 5 to 10 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.
Q.06Which FAA handbook chapter covers aircraft fuel systems?
Chapter 14 of FAA-H-8083-31B, the Aviation Maintenance Technician Handbook: Airframe, titled "Aircraft Fuel Systems". It runs from pages 14-1 to 14-57, and the FAA publishes the whole handbook free as a PDF.
Read the documents, not us
Every fact on this page was read from these on 19 August 2026 and 15 November 2026. They are the authority and we are the summary. If we and one of them disagree, they are right.
- FAA-H-8083-31B, Aviation Maintenance Technician Handbook: Airframe, chapter 14www.faa.gov
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standardswww.faa.gov
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards: the written test blueprints (pages 13 and 14) and chapters 6 and 7www.faa.gov
- FAA, Frequently Missed Knowledge Test ACS Codes, 2nd Quarter CY25www.faa.gov
FREE PLAN · NO CARD · 25 QUESTIONS TO START
The bank holds 320 aircraft fuel systems questions.
Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.
Start freeOr answer a few first. The free FAA A&P practice test runs on the page, with no account.