AMA · AF-13 · FAA-H-8083-31B CH. 13
FAA A&P Airframe: Aircraft Landing Gear Systems
For the FAA A&P Airframe test, aircraft landing gear systems is chapter 13 of FAA-H-8083-31B, Aircraft Landing Gear Systems. Its ACS subject area, Landing Gear Systems, is 5 to 10% of the test, or 5 to 10 of its 100 scored questions. Our question bank holds 424 questions on it, and the 10 below were written for this page.
Test shares and most-missed codes read from the FAA on 15 November 2026.
What FAA-H-8083-31B chapter 13 covers
Chapter 13 covers landing gear types and arrangements, fixed and retractable, and the parts that take a landing: shock struts, the air and oil strut in particular, and how to service and bleed them; shimmy dampers and nosewheel steering; and retraction systems, emergency extension and the safety devices that keep the gear down on the ground.
It then covers wheels; brakes, from single disc to carbon multiple disc; antiskid; bleeding and inspecting brakes; and tires: their construction, inspection, inflation, mounting and storage.
It runs from pages 13-1 to 13-92 of the Aviation Maintenance Technician Handbook: Airframe, which the FAA publishes free as a PDF.
How much of the FAA A&P Airframe test it is
- 5 to 10%OF THE TESTACS area AM.II.E
- 5 to 10QUESTIONSof 100 scored
- 424IN OUR BANKquestions on this subject
The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Landing Gear Systems (AM.II.E) is 5 to 10% (5 to 10 questions) on the 100-question Airframe test. The 15 ranges for the Airframe test add up to anywhere from 75% to 160%, so they say how big an area can get, not how many questions you will see from it.
No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.
Aircraft landing gear systems questions and answers
10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.
- Q.01
Looking at the air valve on top of a shock strut, how can you tell an MS28889-1 valve from an AN6287-1 valve?
FAA-H-8083-31B, ch. 13, p. 13-12
- AIt has a removable valve core under a yellow cap
- BIts swivel nut is the same size as the valve body hex
- CIts swivel nut is clearly smaller than the valve body hex
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Its swivel nut is the same size as the valve body hex
The 2 common strut valves can be told apart by the swivel nut. On the MS28889-1 the nut is the same size as the valve body hex; it has no valve core and is rated to 5,000 psi. The AN6287-1 has a swivel nut smaller than the body hex and carries a valve core. The valve is rated to 3,000 psi, but its core only to 2,000 psi.
- Q.02
A tire has come off the aircraft and is being looked over before it is sent away for retreading. Which of these findings could still be put right at the retread?
FAA-H-8083-31B, ch. 13, p. 13-86
- AA bulge where the tread has lifted away from the carcass
- BA bulge where the plies have separated from each other
- CA cut deep enough to show cords in the sidewall
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
A bulge where the tread has lifted away from the carcass
A bulge caused by the tread separating from the carcass may be repairable when the tire is retreaded, since the old tread comes off and a new one goes on. A bulge caused by ply separation means the carcass itself has come apart, and that tire is discarded. Exposed or damaged sidewall cord is also unacceptable: that tire cannot be repaired or retreaded at all.
- Q.03
After a hard landing, a forged high-pressure wheel is to be checked for cracks in its bead seat area. Why is dye penetrant generally not the method used there?
FAA-H-8083-31B, ch. 13, p. 13-40
- ADye penetrant does not work on aluminum or magnesium wheels
- BPenetrant left in the bead seat would attack the tire bead later
- CCracks there close up tightly once the tire is off and the load is gone
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Cracks there close up tightly once the tire is off and the load is gone
Hard landings can leave distortion or cracks in the bead seat that are very hard to find. Once the tire is dismounted and the stress comes off the metal, those cracks tend to close up tightly, so penetrant cannot get in, and an eddy current check is required instead. The wheel metal is not the problem: the drive key area of the same wheel is usually checked with dye penetrant, and the wheel is cleaned afterward.
- Q.04
After new tires go on all 3 wheels of a tricycle-gear airplane, passengers feel a vibration in the cabin on the takeoff roll. If an out-of-balance wheel is the cause, which assembly is the likeliest source?
FAA-H-8083-31B, ch. 13, p. 13-90
- AEither main wheel, since the mains carry most of the weight
- BThe nose wheel, since its imbalance disturbs the cabin most
- CThe wheel with the newest tire, since new tires are never balanced
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
The nose wheel, since its imbalance disturbs the cabin most
Vibration is the main result of a tire and wheel assembly that is out of balance, and nose wheels tend to create the greatest disturbance in the cabin when imbalanced. The mains carry most of the weight, but that does not make them the likelier source of what the passengers feel. A tire can be balanced once it is mounted, inflated and accepted for service, so new tires are not left unbalanced as a rule.
- Q.05
A crew reports that they touched down far down the runway and had to brake hard to stop in time. What tire damage should you look for?
FAA-H-8083-31B, ch. 13, p. 13-92
- AFlat spots or heat damage from overheating or skidding
- BWear across the center of the tread, as from overinflation
- CWeather checking in the sidewall rubber from ozone
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Flat spots or heat damage from overheating or skidding
Landing too far down the runway and then braking heavily can overheat the tires or make them skid, and that can flat-spot a tire or even blow it out, so those are the things to look for. Wear across the center of the tread is what an overinflated tire develops over time. Weather checking of the sidewall rubber comes from age and exposure, not from one hard stop.
- Q.06
Backing a twin into its parking spot, the line crew lets one main wheel roll off the edge of the ramp onto gravel before it is stopped. What tire risk does that bring?
FAA-H-8083-31B, ch. 13, p. 13-91
- AOnly cosmetic scuffing, since gravel cannot cut a tire
- BA loss of balance, since gravel packs into the tread
- CAn increased risk of internal injury to the tire
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
An increased risk of internal injury to the tire
There is an increased risk of internal tire injury whenever a tire leaves the paved surface, which is why an aircraft being backed into parking is stopped before its main wheels roll off the pavement. Aircraft tires flex far more than car tires, so stones and other objects cut, snag or bruise them more easily, and gravel is not harmless. Loss of balance is not the hazard the handbook names here.
- Q.07
An operator asks whether it is worth paying a shop to dynamically balance a main tire and wheel when the manufacturer only calls for static balance. What does a well-balanced assembly give?
FAA-H-8083-31B, ch. 13, p. 13-90
- AShimmy-free running and less wear on brake and gear parts such as torque links
- BA higher allowable inflation pressure and a longer interval between pressure checks
- CApproval to skip the static balance stand at the next tire change
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Shimmy-free running and less wear on brake and gear parts such as torque links
Static balance is all that most aircraft tires and wheels need, and dynamic balancing is rarely specified by manufacturers. Even so, a well-balanced tire and wheel assembly helps give shimmy-free operation and reduces wear on brake and landing gear parts such as torque links, which is what the operator would be paying for. Balancing has no effect on the specified inflation pressure or on how often it is checked, and it says nothing about the balancing the next tire will need.
- Q.08
You are fitting a tube into a tube-type tire. The tube carries a mark at its heavy spot. Where should that mark sit when the assembly goes together?
FAA-H-8083-31B, ch. 13, p. 13-89
- ADirectly opposite the red dot on the tire
- BLined up with a green dot on the lower sidewall
- CLined up with the red dot on the tire
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Lined up with the red dot on the tire
The red mark on an aircraft tire shows its light spot. Lining the heavy spot of the tube up with it lets the 2 cancel out, so the assembly runs smoother and wears evenly. If the tube has no balance mark, its valve is taken to be the heavy part. Green or white dots on the lower sidewall mark vent holes for trapped gas, not balance.
- Q.09
Before a worn tire is shipped off to be retreaded, the hangar technician looks it over against the retread limits. What is that check for?
FAA-H-8083-31B, ch. 13, p. 13-86
- AIt stands in for the retreader's own tests, which are then skipped
- BIt saves paying to ship a tire that could never be retreaded
- CIt is the inspection the FAA requires before any tire is retreaded
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
It saves paying to ship a tire that could never be retreaded
Retreading is done by FAA certificated retread repair stations, often the original manufacturer. The technician pre-qualifies a tire first so that the cost of shipping it to the retreader is not spent on a tire with no chance of being retreaded. The retreader still inspects and tests every tire, to a level beyond what a hangar or line technician can do, so the hangar check replaces nothing.
- Q.10
Before fitting a tube into a tube-type tire, you run a hand around the inside of the tire and feel a rough, raised spot. Why does that matter?
FAA-H-8083-31B, ch. 13, p. 13-87
- AIt means the tire is a tubeless type and must not take a tube
- BIt can rub through the tube in service and make it fail early
- CIt will throw the wheel out of balance once the tire is inflated
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
It can rub through the tube in service and make it fail early
The inside of a tube-type tire is inspected before a tube goes in, because any protrusion or rough area there tends to abrade the tube and can cause it to fail early. A rough spot says nothing about whether the tire is a tubeless type, which is marked on the sidewall, and it is wear on the tube, not balance, that it threatens.
We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.
How a missed code comes back at the oral
Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.II.E. The examiner reads those codes before your oral and practical.
The Airframe oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Airframe also carries 11 practical projects, each with 2 questions attached.
Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.
Questions people ask about aircraft landing gear systems
Q.01When should an aircraft tire’s pressure be checked?
At ambient temperature, so allow 3 hours after a typical landing for the tire to cool. Tire pressure changes about 1 percent for every 5 degrees F, so the manufacturer gives the right pressure for each ambient temperature in a table or graph.
Q.02How does an air and oil shock strut absorb a landing?
The lower chamber is full of hydraulic fluid and the upper one holds compressed air or nitrogen. As the strut compresses, fluid is forced through an orifice into the upper chamber, often past a metering pin, and that metered flow absorbs the shock. The compressed gas then carries the weight of the aircraft.
Q.03What is a squat switch?
A safety switch on the main landing gear that opens and closes as the strut extends and compresses, so it senses whether the aircraft’s weight is on the wheels. It keeps the gear from being retracted on the ground and tells other systems whether the aircraft is on the ground or in the air.
Q.04What does an antiskid system do?
It detects a wheel that is skidding or about to skid and briefly relieves the brake pressure on that wheel, by connecting it to the hydraulic return line, so the wheel keeps turning. An uncorrected skid can quickly lead to a blown tire and a loss of control.
Q.05How many aircraft landing gear systems questions are on the FAA A&P Airframe test?
The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Landing Gear Systems subject area 5 to 10% of the Airframe test, which is 5 to 10 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.
Q.06Which FAA handbook chapter covers aircraft landing gear systems?
Chapter 13 of FAA-H-8083-31B, the Aviation Maintenance Technician Handbook: Airframe, titled "Aircraft Landing Gear Systems". It runs from pages 13-1 to 13-92, and the FAA publishes the whole handbook free as a PDF.
Read the documents, not us
Every fact on this page was read from these on 19 August 2026 and 15 November 2026. They are the authority and we are the summary. If we and one of them disagree, they are right.
- FAA-H-8083-31B, Aviation Maintenance Technician Handbook: Airframe, chapter 13www.faa.gov
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standardswww.faa.gov
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards: the written test blueprints (pages 13 and 14) and chapters 6 and 7www.faa.gov
- FAA, Frequently Missed Knowledge Test ACS Codes, 2nd Quarter CY25www.faa.gov
FREE PLAN · NO CARD · 25 QUESTIONS TO START
The bank holds 424 aircraft landing gear systems questions.
Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.
Start freeOr answer a few first. The free FAA A&P practice test runs on the page, with no account.