PrepAMT Academy

AMA · AF-16 · FAA-H-8083-31B CH. 16

FAA A&P Airframe: Cabin Environmental Control Systems

For the FAA A&P Airframe test, aircraft cabin environmental systems is chapter 16 of FAA-H-8083-31B, Cabin Environmental Control Systems. Its ACS subject area, Environmental Systems, is 5 to 10% of the test, or 5 to 10 of its 100 scored questions. Our question bank holds 322 questions on it, and the 10 below were written for this page.

Test shares and most-missed codes read from the FAA on 15 November 2026.

01 WHAT IT COVERSFAA-H-8083-31B · CH. 16

What FAA-H-8083-31B chapter 16 covers

Chapter 16 starts with the body: the atmosphere, how the pressure of oxygen falls with altitude, and hypoxia. It covers oxygen systems, gaseous, liquid and chemical, with continuous flow, diluter demand and pressure demand equipment, and how to service oxygen safely.

It then covers pressurization (cabin altitude, differential pressure, outflow and safety valves, and their controllers), air conditioning by air cycle and vapor cycle machines, and heating, from exhaust shrouds and combustion heaters to electric heat.

It runs from pages 16-1 to 16-61 of the Aviation Maintenance Technician Handbook: Airframe, which the FAA publishes free as a PDF.

02 SHARE OF THE TESTFAA-G-ACS-1 · BLUEPRINT

How much of the FAA A&P Airframe test it is

  • 5 to 10%OF THE TESTACS area AM.II.G
  • 5 to 10QUESTIONSof 100 scored
  • 322IN OUR BANKquestions on this subject

The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Environmental Systems (AM.II.G) is 5 to 10% (5 to 10 questions) on the 100-question Airframe test. The 15 ranges for the Airframe test add up to anywhere from 75% to 160%, so they say how big an area can get, not how many questions you will see from it.

No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.

03 EXAMPLE QUESTIONSWRITTEN FOR THIS PAGE

Aircraft cabin environmental systems questions and answers

10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.

  1. Q.01

    You have just refilled a transport's remotely mounted oxygen cylinder in place from a fill cart. How is that cylinder's valve normally left afterward?

    FAA-H-8083-31B, ch. 16, p. 16-18

    1. AClosed, so the lines stay unpressurized until the next flight
    2. BHalf open, so a crew member can shut it quickly in a fire
    3. COpen, which is its normal position for operation
    SHOW THE ANSWER

    THE ANSWER IS C.

    Open, which is its normal position for operation

    Filling ends with the aircraft refill valve and all the cart cylinders closed. The aircraft oxygen cylinder valves are then left in the proper position for normal operations, and remotely mounted cylinders are usually left open. Leaving the valve closed or only partly open would leave the system short of its normal supply, and no filling step calls for either.

  2. Q.02

    You are setting up to work on an aircraft's oxygen system. Which of these should you avoid while the work is going on?

    FAA-H-8083-31B, ch. 16, p. 16-20

    1. APower-on checks that use the aircraft electrical system
    2. BKeeping a suitable fire extinguisher close at hand
    3. CUsing tools that are kept only for oxygen work
    SHOW THE ANSWER

    THE ANSWER IS A.

    Power-on checks that use the aircraft electrical system

    Pure oxygen readily combines with other substances, so ignition sources are kept away from the job. Power-on checks and use of the aircraft electrical system are avoided, the area is cordoned off with no smoking placards, and the work is done outside where possible. Having an extinguisher on hand before work starts is required, and dedicated, clean, grease-free tools are good practice, not things to avoid.

  3. Q.03

    How sensitive should a good electronic leak detector be when it is used on a vapor cycle air conditioning system?

    FAA-H-8083-31B, ch. 16, p. 16-54

    1. AAble to find a leak losing less than half an ounce of refrigerant a year
    2. BAble to find leaks down to a pound of refrigerant a month, but no smaller
    3. CAble to find a leak only once the sight glass shows steady bubbles
    SHOW THE ANSWER

    THE ANSWER IS A.

    Able to find a leak losing less than half an ounce of refrigerant a year

    Even the smallest leak in a vapor cycle system loses refrigerant, so a good electronic leak detector can find leaks that would let less than half an ounce escape in a year. It is held close to the component and hose connections, where most leaks occur, and one made for the system's refrigerant is chosen. A detector that can see nothing smaller than a pound a month, or only finds leaks after the sight glass bubbles, would miss what it is there to catch.

  4. Q.04

    When Teflon tape is used on a tapered pipe fitting in an oxygen system, why is the wrapping started at least 2 threads back from the end of the fitting?

    FAA-H-8083-31B, ch. 16, p. 16-20

    1. ASo the bare threads bite in and make a metal to metal seal
    2. BSo no loose tape can come off and get into the oxygen system
    3. CSo the fitting can be torqued higher without crushing the tape
    SHOW THE ANSWER

    THE ANSWER IS B.

    So no loose tape can come off and get into the oxygen system

    Tapered pipe fittings in oxygen systems are sealed with an oxygen-compatible thread lubricant or sealer, or with Teflon tape, never with an ordinary petroleum-based sealer. The tape is started at least 2 threads from the end of the fitting so that no tape can come loose and get into the oxygen system. Leaving those threads bare is not about a metal to metal seal or about torque.

  5. Q.05

    An oxygen cylinder installed in a light twin is found reading 30 psi. What should happen to it?

    FAA-H-8083-31B, ch. 16, p. 16-6

    1. ATop it up from the cart, since any pressure above zero keeps air out
    2. BRemove it from service, since moist air may have got inside
    3. CLeave it in place until it reads zero, then refill it on the aircraft
    SHOW THE ANSWER

    THE ANSWER IS B.

    Remove it from service, since moist air may have got inside

    A cylinder counts as empty once its pressure drops below 50 psi. Above that, the pressure keeps out air carrying water vapor, which could corrode the inside of the cylinder or freeze and block a narrow passage in the valve or system. An installed cylinder that has been allowed to fall below 50 psi is removed from service.

  6. Q.06

    A light twin carries a portable oxygen system, and on the next trip all 6 seats will be filled. Checking the kit, you find 4 masks. What does the handbook call for?

    FAA-H-8083-31B, ch. 16, p. 16-19

    1. AEnough masks for the crew, since passengers breathe cabin air
    2. BOne mask for every 2 people, since masks can be passed around
    3. CA mask for each person on board who may need oxygen
    SHOW THE ANSWER

    THE ANSWER IS C.

    A mask for each person on board who may need oxygen

    Oxygen masks and hoses are inspected periodically, and leaks, holes and tears are not acceptable. Part of the check is to be sure there is a mask for each potential user on board the aircraft, so 4 masks for 6 occupants is not enough. Masks are not meant to be shared or passed around, and passengers are potential users just as the crew are.

  7. Q.07

    During a quick feel test of a running vapor cycle system, the line going into the receiver dryer is hot, but the line coming out of it is noticeably cooler. What do you make of it?

    FAA-H-8083-31B, ch. 16, p. 16-56

    1. AA discrepancy at the dryer that calls for further checking
    2. BNormal, since the receiver dryer is where the refrigerant sheds its heat
    3. CA sign of a full charge, since a full dryer runs cooler at its outlet
    SHOW THE ANSWER

    THE ANSWER IS A.

    A discrepancy at the dryer that calls for further checking

    In a feel test, the high side from the compressor to the expansion valve should be warm or hot, the low side lines and the evaporator should be cool, and the lines on both sides of the receiver dryer should be the same temperature. A clear difference across the dryer is a discrepancy, and any discrepancy calls for further investigation. The condenser, not the receiver dryer, is where the refrigerant gives up its heat.

  8. Q.08

    A jet climbing in isobaric mode reaches the altitude where its pressurization switches to constant differential mode. If it keeps climbing, what happens to the cabin altitude?

    FAA-H-8083-31B, ch. 16, p. 16-28

    1. AIt stays at the altitude the crew selected, whatever the airplane does
    2. BIt goes down, since the outflow valve now holds more air in the cabin
    3. CIt rises above the selected altitude as the airplane climbs on
    SHOW THE ANSWER

    THE ANSWER IS C.

    It rises above the selected altitude as the airplane climbs on

    In isobaric mode the system holds the cabin altitude the crew selected. Climbing higher would then raise the differential pressure past what the airframe is designed for, so before that limit is reached the mode switches to constant differential. From then on the cabin is held a fixed pressure difference above the falling outside pressure, regardless of the selected cabin altitude, so cabin pressure falls and the cabin altitude climbs too.

  9. Q.09

    After takeoff, the cabin of a pressurized airplane climbs from 1,000 feet to its selected 7,000 feet at a cabin rate of climb of 400 feet per minute. How many minutes does that take?

    FAA-H-8083-31B, ch. 16, p. 16-23

    1. A12 minutes
    2. B17.5 minutes
    3. C15 minutes
    SHOW THE ANSWER

    THE ANSWER IS C.

    15 minutes

    Cabin rate of climb measures how fast the pressure inside the cabin changes, given in feet per minute of cabin altitude change, and 300 to 500 feet per minute is typical. Here the cabin altitude changes by 7,000 minus 1,000, or 6,000 feet, and at 400 feet per minute that takes 6,000 divided by 400, or 15 minutes. 17.5 minutes forgets that the cabin started at 1,000 feet, and 12 minutes uses 500 feet per minute instead of the rate given.

  10. Q.10

    When a gaseous oxygen system is purged by running oxygen through it, about how long does that take?

    FAA-H-8083-31B, ch. 16, p. 16-18

    1. AAbout 30 seconds at cylinder pressure, which suits any system
    2. BFrom about 10 minutes at normal delivery pressure to 30 minutes at a raised one
    3. CAt least 2 hours, the same as the time that makes a purge necessary
    SHOW THE ANSWER

    THE ANSWER IS B.

    From about 10 minutes at normal delivery pressure to 30 minutes at a raised one

    Purging removes contaminants, mostly moisture, and resaturates the inside of the system with oxygen. Oxygen is run through a sound system for a number of minutes at a given pressure: as little as 10 minutes at normal delivery pressure, while other systems need up to 30 minutes of flow at an elevated pressure. The 2-hour figure is when a purge becomes necessary, after a system has been opened or depleted for longer than that.

We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.

04 AND THEN THE ORAL§ 65.79

How a missed code comes back at the oral

Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.II.G. The examiner reads those codes before your oral and practical.

The Airframe oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Airframe also carries 11 practical projects, each with 2 questions attached.

Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.

05 COMMON QUESTIONSFAQ

Questions people ask about aircraft cabin environmental systems

Q.01

Why must oil and grease be kept away from oxygen fittings?

Because pure oxygen combines violently with petroleum products such as fuel, oil and grease. Oxygen is kept away from them, and only aviator’s breathing oxygen goes into an aircraft system, because it is tested for water that could freeze in the small passages of valves and regulators.

Q.02

What is cabin differential pressure?

The cabin’s air pressure minus the air pressure outside it. It runs from about 3.5 psi in a pressurized single-engine piston airplane to about 9 psi in a high performance jet. Cabin pressure is controlled by the outflow valve, which opens, closes or modulates to set how much air leaves the cabin.

Q.03

How does an air cycle machine cool the air?

Bleed air is cooled by ram air in a heat exchanger, then compressed in the air cycle machine and cooled again in a second heat exchanger. It then drives the machine’s expansion turbine, which cools it further, the water is removed, and it is mixed with warm bypassed air to the temperature wanted.

Q.04

Why is an exhaust shroud heater inspected so closely?

Because exhaust gas could reach the cabin air, and even the slightest crack in an exhaust manifold can let in enough carbon monoxide to be fatal. Carbon monoxide has no color or smell, so the exhaust is inspected strictly and carbon monoxide detectors are used as a check.

Q.05

How many aircraft cabin environmental systems questions are on the FAA A&P Airframe test?

The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Environmental Systems subject area 5 to 10% of the Airframe test, which is 5 to 10 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.

Q.06

Which FAA handbook chapter covers aircraft cabin environmental systems?

Chapter 16 of FAA-H-8083-31B, the Aviation Maintenance Technician Handbook: Airframe, titled "Cabin Environmental Control Systems". It runs from pages 16-1 to 16-61, and the FAA publishes the whole handbook free as a PDF.

FREE PLAN · NO CARD · 25 QUESTIONS TO START

The bank holds 322 aircraft cabin environmental systems questions.

Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.

Start free

Or answer a few first. The free FAA A&P practice test runs on the page, with no account.