PrepAMT Academy

AMA · AF-17 · FAA-H-8083-31B CH. 17

FAA A&P Airframe: Fire Protection Systems

For the FAA A&P Airframe test, aircraft fire protection systems is chapter 17 of FAA-H-8083-31B, Fire Protection Systems. Its ACS subject area, Airframe Fire Protection Systems, is 5 to 10% of the test, or 5 to 10 of its 100 scored questions. Our question bank holds 208 questions on it, and the 10 below were written for this page.

Test shares and most-missed codes read from the FAA on 15 November 2026.

01 WHAT IT COVERSFAA-H-8083-31B · CH. 17

What FAA-H-8083-31B chapter 17 covers

Chapter 17 covers what a fire needs and how fires are detected: thermal switches, thermocouples, continuous loop detectors, pneumatic detectors and flame detectors, and smoke, flame and carbon monoxide detection in cabins, cargo compartments and lavatories.

It then covers the extinguishing agents and fixed systems, the high rate discharge containers with their cartridges and discharge indicators, and how detection and extinguishing systems are inspected and maintained.

It runs from pages 17-1 to 17-20 of the Aviation Maintenance Technician Handbook: Airframe, which the FAA publishes free as a PDF.

02 SHARE OF THE TESTFAA-G-ACS-1 · BLUEPRINT

How much of the FAA A&P Airframe test it is

  • 5 to 10%OF THE TESTACS area AM.II.M
  • 5 to 10QUESTIONSof 100 scored
  • 208IN OUR BANKquestions on this subject

The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Airframe Fire Protection Systems (AM.II.M) is 5 to 10% (5 to 10 questions) on the 100-question Airframe test. The 15 ranges for the Airframe test add up to anywhere from 75% to 160%, so they say how big an area can get, not how many questions you will see from it.

No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.

03 EXAMPLE QUESTIONSWRITTEN FOR THIS PAGE

Aircraft fire protection systems questions and answers

10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.

  1. Q.01

    Why are the fire detector sensing elements around an engine so easily damaged while other maintenance is being done?

    FAA-H-8083-31B, ch. 17, p. 17-17

    1. ATheir sheaths turn brittle once they have signaled a fire
    2. BThey are small and run through busy areas around the engine
    3. CThe flight deck test current slowly weakens their wiring
    SHOW THE ANSWER

    THE ANSWER IS B.

    They are small and run through busy areas around the engine

    It comes down to where the elements are and how small they are. They run through many busy areas around the engine, so work done nearby can crush, pinch or rub them, which is why the inspection looks for crushing, abrasion, kinks and loose joints. Heating a thermistor element makes no lasting change to it, and the flight deck test only simulates the resistance change a fire would cause, so neither one wears the element out.

  2. Q.02

    A Class C cargo compartment must have a way to control the ventilation and drafts inside it. What is that for?

    FAA-H-8083-31B, ch. 17, p. 17-14

    1. ATo clear smoke out so the crew can see where the fire is
    2. BTo let a crewmember reach every part with a hand extinguisher
    3. CSo the agent it releases can control any fire that starts
    SHOW THE ANSWER

    THE ANSWER IS C.

    So the agent it releases can control any fire that starts

    A Class C compartment is one that does not meet the Class A or Class B requirements, so a fire there is fought by its built-in extinguishing or suppression system, worked from the flight deck. Air moving freely through the compartment would carry the agent away and bring fresh air to the fire, so there must be a way to control ventilation and drafts and let the agent do its job. Being able to reach every part with a hand extinguisher is what makes a compartment Class B.

  3. Q.03

    At the preflight integrity test, one loop of an engine's dual-loop fire detection system is found inoperative. A selector takes that loop out so the other loop warns alone, and the airplane is dispatched with the repair put off until later. What makes that acceptable?

    FAA-H-8083-31B, ch. 17, p. 17-5

    1. AThe working loop alone satisfies every requirement for a fire detector
    2. BThe engine's fire bottles go off by themselves if a fire starts in flight
    3. CThe failed loop still gives its overheat warnings after it is switched out
    SHOW THE ANSWER

    THE ANSWER IS A.

    The working loop alone satisfies every requirement for a fire detector

    A dual-loop system normally needs both loops to agree before it warns, which guards against false alarms. When one loop fails the preflight test, a flight deck selector disconnects it and lets the other loop give the warning by itself. That one loop satisfies every fire detector requirement on its own, so the airplane can go and the repair can wait for a more convenient time. A loop that has been switched out gives no warnings of any kind, and engine bottles are discharged by the crew through the fire switch, not on their own.

  4. Q.04

    A magnesium wheel is burning on the ramp, and someone grabs a Halon 1211 extinguisher. Why should it not be used on that fire?

    FAA-H-8083-31B, ch. 17, p. 17-9

    1. AHalon can react violently with the burning metal
    2. BHalon leaves a corrosive film on magnesium parts
    3. CHalon is a flooding agent and cannot be aimed at a wheel
    SHOW THE ANSWER

    THE ANSWER IS A.

    Halon can react violently with the burning metal

    Burning magnesium is a Class D fire. Halons are right for Class A, B and C fires, but they are not used on a Class D fire, because the agent may react vigorously with the burning metal. A specialized dry powder recommended for that metal is the agent to use. Halon is a clean agent that leaves no residue, and Halon 1211 is the streaming type, made to be aimed at a fire.

  5. Q.05

    A hand-held Halon extinguisher in a cabin has just been emptied on a small fire. What is suggested for the unit that replaces it?

    FAA-H-8083-31B, ch. 17, p. 17-9

    1. AA CO2 unit, since carbon dioxide leaves no residue behind
    2. BA dry chemical unit, since it is rated for every class of fire
    3. CA Halon replacement agent unit, though that is not required
    SHOW THE ANSWER

    THE ANSWER IS C.

    A Halon replacement agent unit, though that is not required

    Halon production has been restricted because it depletes the ozone layer, so when a Halon extinguisher is discharged the guidance is to consider replacing it with one that uses a Halon replacement agent, such as HFC-227ea or HFC-236fa. It is a suggestion, not a requirement. CO2 is not recommended for hand-held extinguishers inside the aircraft, and dry chemical is unsuitable in the cabin and flight deck because of corrosion, poor visibility and cleanup.

  6. Q.06

    You need to know how much service life is left on the discharge cartridge of an installed fire bottle. What do you usually have to do to find out?

    FAA-H-8083-31B, ch. 17, p. 17-19

    1. ATake off its leads and discharge line, then remove the plug body
    2. BRead the bottle's pressure gauge against the temperature chart
    3. CWeigh the bottle and compare the result with its stamped weight
    SHOW THE ANSWER

    THE ANSWER IS A.

    Take off its leads and discharge line, then remove the plug body

    Cartridge service life is counted from the manufacturer's date stamp, usually on the face of the cartridge, and is normally given in years. With the bottle installed you usually cannot see it, so the electrical leads and the discharge line come off the plug body, and the plug body is then removed from the container. The pressure chart and weighing tell you about the agent charge, not about the age of the cartridge.

  7. Q.07

    On a walkaround, you find the red disc missing from the fuselage skin beside an engine fire bottle. What has to happen before the next flight?

    FAA-H-8083-31B, ch. 17, p. 17-13

    1. ARefit a red disc and enter the bottle pressure in the log
    2. BReplace the fire bottle that the red disc belongs to
    3. CRun the engine fire detection test from the flight deck
    SHOW THE ANSWER

    THE ANSWER IS B.

    Replace the fire bottle that the red disc belongs to

    The red disc is on an indicator connected to the container's relief fitting. When excessive heat drives the pressure up, the contents dump overboard through the opening the disc leaves, so a missing red disc means the agent is gone. The flight and maintenance crews take it as the sign that the container must be replaced before the next flight. A new disc on an empty bottle protects nothing, and a detection test says nothing about the agent.

  8. Q.08

    A thermal switch fire warning system has several switches wired to one warning light. The lead running to just one of those switches breaks open. What does that do?

    FAA-H-8083-31B, ch. 17, p. 17-2

    1. AIt turns the warning light on, and the light stays on
    2. BIt stops every switch from lighting the warning until it is fixed
    3. COnly that switch can no longer light the warning; the rest still can
    SHOW THE ANSWER

    THE ANSWER IS C.

    Only that switch can no longer light the warning; the rest still can

    Thermal switches are connected in parallel with each other but in series with the indicator light. Any one switch that reaches its set temperature closes and completes the light circuit by itself, so a break in the lead to one switch takes only that switch out, and the others still work. The light comes on only when a switch closes, not when a lead opens, and a break could only disable them all if the switches were wired in series.

  9. Q.09

    An airplane with 40 passenger seats has a lavatory smoke detector, but no lavatory smoke light in the flight deck. What else can give an acceptable smoke warning?

    FAA-H-8083-31B, ch. 17, p. 17-16

    1. AAn automatic bottle in the waste bin that fires when it gets too hot
    2. BA fault message stored for maintenance to read after landing
    3. CA light or sound at the lavatory and at flight attendant stations
    SHOW THE ANSWER

    THE ANSWER IS C.

    A light or sound at the lavatory and at flight attendant stations

    Airplanes with a passenger capacity of 20 or more must monitor their lavatories for smoke. The warning can be a light in the flight deck, or a warning light or audible warning at the lavatory and at the flight attendant stations that a flight attendant would readily notice. The automatic waste bin extinguisher is a separate requirement, not a warning, and a message read only after landing comes far too late.

  10. Q.10

    Smoke and flames are coming from a powered electrical panel in a transport airplane's cabin. Which of the cabin's hand extinguishers should go on it?

    FAA-H-8083-31B, ch. 17, p. 17-10

    1. AThe water extinguisher, since water cools the burning parts the best
    2. BThe Halon 1211 extinguisher, since it does not conduct electricity
    3. CThe water unit first to cool it, then the Halon unit to finish it
    SHOW THE ANSWER

    THE ANSWER IS B.

    The Halon 1211 extinguisher, since it does not conduct electricity

    A fire in energized electrical equipment is a Class C fire, and the agent has to be electrically nonconducting. Halon 1211 is a clean, nonconducting streaming agent, and Halon extinguishers are the ones meant for electrical and flammable liquid fires. Transport cabins that carry water extinguishers carry them for non-electrical fires, so water does not go on powered equipment at all, first or last.

We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.

04 AND THEN THE ORAL§ 65.79

How a missed code comes back at the oral

Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.II.M. The examiner reads those codes before your oral and practical.

The Airframe oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Airframe also carries 11 practical projects, each with 2 questions attached.

Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.

05 COMMON QUESTIONSFAQ

Questions people ask about aircraft fire protection systems

Q.01

How does a continuous loop fire detector work?

In one common type, a control unit puts a small voltage on a sensing element run around the area. At an overheat anywhere along it, the resistance of the salt inside drops sharply, current flows between the sheath and the center conductor, and the control unit sets off the alarm. It resets itself once the area cools.

Q.02

What do the discharge indicator discs show?

A red disc blown out means the container has dumped its agent overboard because it got too hot. A yellow disc blown out means the crew fired the system, and the container has to be replaced before the next flight.

Q.03

How is a fire extinguisher container checked?

By checking that its pressure is between the prescribed minimum and maximum. Container pressure changes with the ambient temperature, so the gauge reading is compared with a pressure and temperature graph that gives the limits for the temperature at the time.

Q.04

What sets off a fixed fire extinguisher container?

A cartridge, often called a squib, in the outlet of the discharge valve. Fired electrically, its explosive energy drives a slug through the closure disc, or ruptures the disc directly, and the agent flows into the engine or compartment.

Q.05

How many aircraft fire protection systems questions are on the FAA A&P Airframe test?

The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Airframe Fire Protection Systems subject area 5 to 10% of the Airframe test, which is 5 to 10 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.

Q.06

Which FAA handbook chapter covers aircraft fire protection systems?

Chapter 17 of FAA-H-8083-31B, the Aviation Maintenance Technician Handbook: Airframe, titled "Fire Protection Systems". It runs from pages 17-1 to 17-20, and the FAA publishes the whole handbook free as a PDF.

FREE PLAN · NO CARD · 25 QUESTIONS TO START

The bank holds 208 aircraft fire protection systems questions.

Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.

Start free

Or answer a few first. The free FAA A&P practice test runs on the page, with no account.