PrepAMT Academy

AMA · AF-18 · FAA-H-8083-31B CH. 2

FAA A&P Airframe: Airframe Inspection

For the FAA A&P Airframe test, airframe inspection is the Aircraft Inspection section of FAA-H-8083-31B chapter 2, pages 2-58 to 2-67. Its ACS subject area, Airframe Inspection, is 5 to 15% of the test, or 5 to 15 of its 100 scored questions. Our question bank holds 178 questions on it, and the 10 below were written for this page.

Test shares and most-missed codes read from the FAA on 15 November 2026.

01 WHAT IT COVERSFAA-H-8083-31B · CH. 2

What the Aircraft Inspection section of FAA-H-8083-31B chapter 2 covers

The closing section of chapter 2 is about inspecting the aircraft as a whole. It starts with what airworthy means, conforming to its type design and being in a condition for safe operation, and how to check conformity against the type certificate data sheet, the manufacturer’s data and the aircraft records.

It covers the required inspections and programs: the annual and 100-hour inspections, progressive inspections, continuous airworthiness maintenance programs, the altimeter, static system and transponder inspections, helicopter inspections, aging airplane inspections and corrosion prevention and control programs.

It runs from pages 2-58 to 2-67 of the Aviation Maintenance Technician Handbook: Airframe, which the FAA publishes free as a PDF.

02 SHARE OF THE TESTFAA-G-ACS-1 · BLUEPRINT

How much of the FAA A&P Airframe test it is

  • 5 to 15%OF THE TESTACS area AM.II.D
  • 5 to 15QUESTIONSof 100 scored
  • 178IN OUR BANKquestions on this subject

The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Airframe Inspection (AM.II.D) is 5 to 15% (5 to 15 questions) on the 100-question Airframe test. The 15 ranges for the Airframe test add up to anywhere from 75% to 160%, so they say how big an area can get, not how many questions you will see from it.

The FAA’s latest report on the most-missed codes (2nd Quarter, CY25, 1 July 2024 to 30 June 2025) lists AM.II.D.K5, “Special inspections”, in this area, missed 79.53% of the time on the Airframe test. That is a whole subject element across everyone who took the test, not one question, and it is the part of this subject the FAA says people get wrong most.

03 EXAMPLE QUESTIONSWRITTEN FOR THIS PAGE

Airframe inspection questions and answers

10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.

  1. Q.01

    A private owner flies a twin turboprop that weighs 9,500 pounds. Which inspection requirement applies to it?

    FAA-H-8083-31B, ch. 2, p. 2-59

    1. AOnly an annual inspection, since it weighs under 12,500 pounds
    2. BAn inspection program picked from those the rule allows
    3. CAn annual and a 100-hour inspection, since its engines are turbines
    SHOW THE ANSWER

    THE ANSWER IS B.

    An inspection program picked from those the rule allows

    The inspection rule for large airplanes reaches further than its name: it covers large airplanes, turbojet multiengine airplanes, turbopropeller powered multiengine airplanes and turbine powered rotorcraft. The owner or operator must select one of the inspection programs that rule lists. Being under 12,500 pounds does not put this twin back on the annual, and turbine engines do not add a 100-hour inspection on top.

  2. Q.02

    An A&P mechanic without an inspection authorization is asked to do 2 jobs: the annual on a standard category airplane, and the yearly condition inspection on an experimental light sport airplane. Which may the mechanic sign off?

    FAA-H-8083-31B, ch. 2, p. 2-66

    1. AOnly the annual, since a condition inspection needs a repairman
    2. BThe condition inspection, but only with an FAA inspector present
    3. COnly the condition inspection on the light sport airplane
    SHOW THE ANSWER

    THE ANSWER IS C.

    Only the condition inspection on the light sport airplane

    An annual inspection needs an A&P who also holds an inspection authorization. The condition inspection on a light sport or experimental aircraft can be done by an A&P or an appropriately rated repair station, so this mechanic may do and sign that one. It matches the scope and detail of an annual, but that does not change who may sign the annual. A repairman certificate is another way to get a condition inspection done, not the only one, and no FAA inspector has to be there.

  3. Q.03

    In one week, 2 ELTs in the shop transmit by accident. One has a conventional battery, well inside its marked date, that now has 20 minutes of transmitter use in total. The other has a water activated battery that was activated and ran for 10 minutes. Which battery must be replaced?

    FAA-H-8083-31B, ch. 2, p. 2-61

    1. AOnly the water activated one, even though it ran for the shorter time
    2. BOnly the conventional one, since any transmitting voids its marked date
    3. CEach of them, since an accidental transmission uses up a battery
    SHOW THE ANSWER

    THE ANSWER IS A.

    Only the water activated one, even though it ran for the shorter time

    A conventional ELT battery is replaced on the expiration date marked on the transmitter, which is set at 50 percent of its useful life, or once the transmitter has been in use for more than 1 cumulative hour. 20 minutes is well short of that hour, so that battery can stay. A water activated battery has almost unlimited shelf life and usually carries no date, but any activation at all, however short, means it has to be replaced. So only the water activated battery has to go.

  4. Q.04

    A part 135 operator flies small aircraft with 9 passenger seats. What does an approved aircraft inspection program let it do that repeated 100-hour inspections do not?

    FAA-H-8083-31B, ch. 2, p. 2-64

    1. ALeave the avionics and emergency equipment out of its inspections
    2. BSet its own task procedures and intervals to suit the aircraft's needs
    3. CHand the responsibility for the program over to the local FSDO
    SHOW THE ANSWER

    THE ANSWER IS B.

    Set its own task procedures and intervals to suit the aircraft's needs

    Under an approved aircraft inspection program, the operator works out its own procedures and time intervals for the inspection tasks, matched to what each aircraft needs, so the full list of tasks does not have to come round every 100 hours. Responsibility for the program sits with the operator, not the FSDO, and the program has to take in the whole aircraft, avionics, emergency equipment and cargo provisions included.

  5. Q.05

    Why should a technician look over the landing gear, wheels, tires and brakes whenever there is a chance, and not only at scheduled inspections?

    FAA-H-8083-31B, ch. 13, p. 13-36

    1. AGear parts are rarely covered by any inspection checklist
    2. BThe gear is always the first item an FAA inspector checks
    3. CThe landing gear area is a hostile environment for those parts
    SHOW THE ANSWER

    THE ANSWER IS C.

    The landing gear area is a hostile environment for those parts

    The landing gear works in such a hostile environment that the technician should inspect it, including the wheels, tires and brakes, whenever possible, not only when an inspection comes due. The gear is far from left out of the checklists: it is a full group of the annual and 100-hour inspection. Nothing makes it the first thing an FAA inspector looks at.

  6. Q.06

    An owner brings an airplane in for its annual inspection and is not sure what the inspection involves. What should happen before the inspection starts?

    FAA-H-8083-31B, ch. 2, p. 2-62

    1. AStart right away and explain the inspection when the bill is ready
    2. BReview the records with the owner and talk through any known problems
    3. CAsk the owner to sign the discrepancy list before anything is found
    SHOW THE ANSWER

    THE ANSWER IS B.

    Review the records with the owner and talk through any known problems

    Before the inspection starts, the person doing it sits down with the owner to review the records and discuss any maintenance issues, repairs needed or extra work the owner wants. Time spent on this before the work begins usually saves time and money before the job is done. Explaining only when the bill comes defeats that purpose, and a discrepancy list can only come from the finished inspection.

  7. Q.07

    At the start of an annual inspection, the inspection plates, access doors, fairings and cowling have all come off. What should be done before you work through the checklist items?

    FAA-H-8083-31B, ch. 2, p. 2-62

    1. AClean the entire aircraft before any item is inspected
    2. BGive the owner the list of discrepancies found up to that point
    3. CRun the engine for the return to service performance check
    SHOW THE ANSWER

    THE ANSWER IS A.

    Clean the entire aircraft before any item is inspected

    Once the aircraft is opened up, the entire aircraft is cleaned to uncover hidden cracks or defects that dirt could cover. Then each item is inspected in order, following the checklist, and discrepancies are recorded as they are found. The discrepancy list goes to the owner once the entire aircraft has been inspected, and the engine run that checks performance comes before return to service, at the end.

  8. Q.08

    A part 135 operator flies 5 airplanes of one model under its approved aircraft inspection program, but 2 of them carry a different avionics fit. What should the program include for this?

    FAA-H-8083-31B, ch. 2, p. 2-64

    1. ALeaving avionics out of the program for the 2 that are different
    2. BA waiver from the FSDO for each airplane that does not match
    3. CA way to allow for the equipment differences across its fleet
    SHOW THE ANSWER

    THE ANSWER IS C.

    A way to allow for the equipment differences across its fleet

    One of the elements an approved aircraft inspection program should include is accommodation for variations in equipment and configurations between aircraft in the fleet. The program has to cover the total aircraft, avionics included, so the differences are written into the program itself. Leaving the avionics of the 2 odd airplanes out of the program, or asking the FSDO for a waiver for each, is not what the program calls for.

  9. Q.09

    A company privately flies 2 aircraft that are each under 12,500 pounds: a single-engine turboprop airplane and a single-engine turbine helicopter. Which of them falls under the inspection rule for large and turbine aircraft?

    FAA-H-8083-31B, ch. 2, p. 2-59

    1. AOnly the single-engine turboprop airplane
    2. BEach of them, since both are turbine powered
    3. COnly the single-engine turbine helicopter
    SHOW THE ANSWER

    THE ANSWER IS C.

    Only the single-engine turbine helicopter

    That rule takes in large airplanes, any multiengine airplane with turbojet or turboprop engines, and any rotorcraft with turbine power. For an airplane under 12,500 pounds, a turbine engine brings it in only when there is more than one engine, so the single-engine turboprop stays on the annual inspection. For rotorcraft there is no engine count: any turbine powered rotorcraft is covered, though its operator may still elect the annual, 100-hour or progressive inspection.

  10. Q.10

    Why should a part 135 operator's manual have a section that clearly describes its whole approved aircraft inspection program, with its scheduling, recording and accountability?

    FAA-H-8083-31B, ch. 2, p. 2-65

    1. AIt helps the operator run the program and directs those doing the work
    2. BIt stands in for the aircraft records the operator would otherwise keep
    3. CIt is the document the FSDO signs to show the program is approved
    SHOW THE ANSWER

    THE ANSWER IS A.

    It helps the operator run the program and directs those doing the work

    The operator's manual should carry a section that clearly describes the complete program, including how it is scheduled, recorded and kept accountable. That section makes the program easier for the certificate holder to administer, and it directs how the mechanics or repair stations carry it out. The completed work forms still have to satisfy the aircraft records rule, and when the FSDO approves the program it issues computer-generated operations specifications.

We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.

04 AND THEN THE ORAL§ 65.79

How a missed code comes back at the oral

Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.II.D. The examiner reads those codes before your oral and practical.

The Airframe oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Airframe also carries 11 practical projects, each with 2 questions attached.

Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.

05 COMMON QUESTIONSFAQ

Questions people ask about airframe inspection

Q.01

What does airworthy mean?

Under 14 CFR 3.5, that the aircraft conforms to its type design and is in a condition for safe operation. Both must be true: an aircraft built exactly to its design but worn past its limits is not airworthy, and nor is a sound one carrying an alteration that was never approved.

Q.02

Where does a conformity inspection start?

With the type certificate data sheet, the FAA’s formal description of the aircraft. It lists the limits and the engines, propellers and other parts eligible for installation, and the aircraft is checked against it, against any supplemental type certificates and against its records.

Q.03

What is a progressive inspection?

An alternative to the annual inspection under 14 CFR 91.409(d). The owner or operator asks the local FAA office in writing, and the program must inspect the whole aircraft within each 12 calendar months. An FAA A&P mechanic may do the inspections under the supervision of a mechanic who holds an inspection authorization.

Q.04

What is a continuous airworthiness maintenance program?

The maintenance program of an operator holding an air carrier or operating certificate under 14 CFR Part 121 or 135, whose inspection program is part of it.

Q.05

How many airframe inspection questions are on the FAA A&P Airframe test?

The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Airframe Inspection subject area 5 to 15% of the Airframe test, which is 5 to 15 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.

Q.06

Which FAA handbook chapter covers airframe inspection?

The Aircraft Inspection section at the end of chapter 2 of FAA-H-8083-31B, the Aviation Maintenance Technician Handbook: Airframe, pages 2-58 to 2-67. The handbook has no chapter of its own for it. The FAA publishes the whole handbook free as a PDF.

FREE PLAN · NO CARD · 25 QUESTIONS TO START

The bank holds 178 airframe inspection questions.

Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.

Start free

Or answer a few first. The free FAA A&P practice test runs on the page, with no account.