PrepAMT Academy

AMA · AF-05 · FAA-H-8083-31B CH. 5

FAA A&P Airframe: Aircraft Welding

For the FAA A&P Airframe test, aircraft welding is chapter 5 of FAA-H-8083-31B, Aircraft Welding. Its ACS subject area, Metallic Structures, is 5 to 15% of the test, or 5 to 15 of its 100 scored questions. Our question bank holds 245 questions on it, and the 10 below were written for this page.

Test shares and most-missed codes read from the FAA on 15 November 2026.

01 WHAT IT COVERSFAA-H-8083-31B · CH. 5

What FAA-H-8083-31B chapter 5 covers

Chapter 5 covers the kinds of welding used on aircraft: gas welding, arc welding (shielded metal, gas metal and gas tungsten arc) and electric resistance welding. It covers the oxy-acetylene equipment, setting up and lighting the torch, the 3 kinds of flame, and welding steel, aluminum, magnesium and titanium.

It also covers soldering and brazing, the kinds of weld joint and the welding positions, what a good weld looks like and the defects to look for, and repairs to steel tube structures.

It runs from pages 5-1 to 5-35 of the Aviation Maintenance Technician Handbook: Airframe, which the FAA publishes free as a PDF.

02 SHARE OF THE TESTFAA-G-ACS-1 · BLUEPRINT

How much of the FAA A&P Airframe test it is

  • 5 to 15%OF THE TESTACS area AM.II.A
  • 5 to 15QUESTIONSof 100 scored
  • 245IN OUR BANKquestions on this subject

The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Metallic Structures (AM.II.A) is 5 to 15% (5 to 15 questions) on the 100-question Airframe test. The 15 ranges for the Airframe test add up to anywhere from 75% to 160%, so they say how big an area can get, not how many questions you will see from it.

Metallic Structures is not ours alone to cover: our Aircraft Structures, Aircraft Metal Structural Repair and Aircraft Painting and Finishing questions are written to the same area.

No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.

03 EXAMPLE QUESTIONSWRITTEN FOR THIS PAGE

Aircraft welding questions and answers

10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.

  1. Q.01

    Why are the regulator and hose connections on an oxy-acetylene outfit tightened only enough to stop leaks?

    FAA-H-8083-31B, ch. 5, p. 5-10

    1. ASo they can be undone by hand quickly if a flashback starts
    2. BThey are brass, which is easily damaged by too much torque
    3. CSo the check valves behind them stay free to open and close
    SHOW THE ANSWER

    THE ANSWER IS B.

    They are brass, which is easily damaged by too much torque

    The connection fittings on welding regulators and hoses are brass, and brass is easily damaged. They do not need much torque to seal, so they are tightened only enough to prevent leakage, and overtightening only spoils them. A flashback is dealt with by shutting off the gases at once, not by undoing fittings, and the check valves do not depend on how tight the connections are.

  2. Q.02

    Until the mid 1950s, aircraft parts under 3/16 inch thick were mostly gas welded in production. Why did electric welding take over?

    FAA-H-8083-31B, ch. 5, p. 5-1

    1. AGas welds in thin steel were found to crack in service
    2. BGas welding could not be used on 4130 chrome-moly tubing
    3. CFor economic reasons, not because gas welds were weaker
    SHOW THE ANSWER

    THE ANSWER IS C.

    For economic reasons, not because gas welds were weaker

    Gas welding was the method most used in production for aircraft materials under 3/16 inch thick until the mid 1950s, when electric welding replaced it for economic reasons, not engineering ones. Gas welds had not been found wanting, and 4130 tubing is gas welded to this day. Gas welding is still a very popular and proven method for repair work.

  3. Q.03

    Protective clothing and head gear are part of arc welding in any position. Why does the handbook stress them for overhead welding in particular?

    FAA-H-8083-31B, ch. 5, p. 5-28

    1. AGravity makes the molten metal drop or sag from the plate onto the welder
    2. BThe arc gives off far more ultraviolet light when it points upward
    3. COverhead welding is done with a long arc, which throws sparks much farther
    SHOW THE ANSWER

    THE ANSWER IS A.

    Gravity makes the molten metal drop or sag from the plate onto the welder

    Overhead, the puddle is above the welder, and gravity tends to make the molten metal drop down or sag from the plate. That is why the handbook says protective clothing and head gear are to be worn at all times for overhead welding. The ultraviolet light from the arc does not depend on which way it points, and overhead welding calls for a very short arc, held constantly to control the molten metal, not a long one.

  4. Q.04

    You are gas welding an aluminum part with flux, and a brilliant yellow-orange glare coming off the flux hides the puddle. What should you change?

    FAA-H-8083-31B, ch. 5, p. 5-9

    1. AWear a special lens made to filter out the sodium flare
    2. BGo to the darkest ordinary shade that still lets you see the work
    3. CWeld without the flux, so there is nothing left to glow
    SHOW THE ANSWER

    THE ANSWER IS A.

    Wear a special lens made to filter out the sodium flare

    The glare is the sodium in the flux, which the torch heat makes glow a brilliant yellow-orange. Picking the darkest shade that still shows the work was the old way of choosing a lens, and it does not get past the flare: other lens types and colors were tried without much success. What works is the special green-glass lens made for aluminum oxy-fuel welding: it cuts the sodium flare completely and still protects the eyes. Leaving the flux off is no fix, because gas welding aluminum needs flux to break down the surface oxides.

  5. Q.05

    Acetylene cylinders are stored and carried standing up. What can go wrong if one is used soon after it has been lying on its side?

    FAA-H-8083-31B, ch. 5, p. 5-10

    1. AThe porous filler packs down at one side, so the cylinder holds less gas
    2. BThe safety plug in the cylinder softens and lets the gas out early
    3. CLiquid acetone gets into the regulator and hose, and the torch can flash back
    SHOW THE ANSWER

    THE ANSWER IS C.

    Liquid acetone gets into the regulator and hose, and the torch can flash back

    An acetylene cylinder holds an absorbent filler soaked in liquid acetone, with the gas dissolved in it. On its side, acetone can reach the valve and contaminate the regulator, hose and torch, which starves the flame of fuel and can lead to a flashback. That is why a cylinder that has been on its side is stood upright for at least twice as long before it is used.

  6. Q.06

    You are inspecting a gas weld on a steel tube cluster. The bead is rough, uneven and pitted, though you can see no cracks. What should you conclude?

    FAA-H-8083-31B, ch. 5, p. 5-15

    1. AIt only needs filing smooth to bring it up to standard
    2. BIt is sound as long as dye penetrant shows no surface cracks
    3. CIt is almost certainly poor inside as well and should be rejected
    SHOW THE ANSWER

    THE ANSWER IS C.

    It is almost certainly poor inside as well and should be rejected

    A clean, smooth bead does not prove a weld is good, since it can still be weak inside. A rough, uneven, pitted bead is the other way round: it is almost always unsatisfactory inside as well. A surface crack check cannot show what is wrong inside the bead, and filing a weld to make it look better only takes away part of its strength.

  7. Q.07

    A job is at the far end of the hangar, so a helper wants to join several lengths of welding hose into one long run. Why does the handbook advise against it?

    FAA-H-8083-31B, ch. 5, p. 5-11

    1. ASplices are allowed in the oxygen hose, but never anywhere in the fuel hose
    2. BA long hose with many splices can restrict the gas flow and starve the tip
    3. CA long hose holds so much gas that the flame stays lit after shutoff
    SHOW THE ANSWER

    THE ANSWER IS B.

    A long hose with many splices can restrict the gas flow and starve the tip

    A tip needs the correct volume of gas for its size. The handbook lists an excessively long hose, one with multiple splices, or one too small in diameter among the things to avoid, because it can restrict the flow of gas, and a tip starved of gas overheats and can flash back. The advice covers both hoses, not only the fuel hose. Closing the torch valves stops the gas at the torch, so a long hose does not keep the flame alight.

  8. Q.08

    Before gas welding a 1/4-inch chrome-moly fitting, you preheat the area around the joint to 300 °F to 400 °F. What is that preheat there to prevent?

    FAA-H-8083-31B, ch. 5, p. 5-16

    1. AOxide inclusions and fissures from too much oxygen in the flame
    2. BBrittle untempered martensite from the weld cooling too suddenly
    3. CCarbon pickup that leaves the metal harder next to the weld
    SHOW THE ANSWER

    THE ANSWER IS B.

    Brittle untempered martensite from the weld cooling too suddenly

    Chrome-moly over 3/16 inch thick is preheated because without it the weld area is quenched so suddenly that it forms untempered martensite, a brittle, glass-like structure that tends to crack near the edge of the weld and has to be removed by post-weld heat treatment. Oxide inclusions come from an oxidizing flame and carbon pickup from a carburizing one, which is why the flame is kept neutral.

  9. Q.09

    You are learning stick welding, and the fumes rising off the work keep hiding the puddle from you. What does the handbook tell you to do?

    FAA-H-8083-31B, ch. 5, p. 5-28

    1. AKeep your head off to the side and out of the fumes so you can see the puddle
    2. BWeld by the sound of the arc alone, and look at the bead only after each pass
    3. CChange to a lighter lens shade so the puddle shows through the smoke
    SHOW THE ANSWER

    THE ANSWER IS A.

    Keep your head off to the side and out of the fumes so you can see the puddle

    An arc welder should always have a good view of the weld puddle. Without it there is no way to be sure the weld is going into the joint and the arc is staying on the leading edge of the puddle. For the best view, the handbook says to keep your head off to the side and out of the fumes. Looking only after each pass is too late to guide the weld, and a lighter lens does nothing about smoke while letting more arc light reach your eyes.

  10. Q.10

    You are heating a finger-type patch plate to form it around a dented tube cluster. Where does the handbook say to take particular care not to damage the plate?

    FAA-H-8083-31B, ch. 5, p. 5-31

    1. AAt the tip of each finger, where it ends along the tube
    2. BAt the point of the angle between any 2 adjacent fingers
    3. CAt the middle of the plate, directly over the dent itself
    SHOW THE ANSWER

    THE ANSWER IS B.

    At the point of the angle between any 2 adjacent fingers

    The plate is heated and formed around the joint to a snug, smooth contour, with a gap of no more than 1/16 inch. During that forming, the handbook warns against unnecessary heating and asks for care to prevent damage at the point of the angle formed by any 2 adjacent fingers. The finger tips and the middle of the plate carry no such warning; the fingers simply have to reach at least 1.5 times the tube diameter along each tube.

We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.

04 AND THEN THE ORAL§ 65.79

How a missed code comes back at the oral

Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.II.A. The examiner reads those codes before your oral and practical.

The Airframe oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Airframe also carries 11 practical projects, each with 2 questions attached.

Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.

05 COMMON QUESTIONSFAQ

Questions people ask about aircraft welding

Q.01

What is a neutral flame?

An oxy-acetylene flame made by a balanced mixture of acetylene and oxygen. It is used for most welding because it does not change the composition of the base metal, and it is the flame set first, before the torch is adjusted to either of the other 2.

Q.02

What is the difference between a carburizing and an oxidizing flame?

A carburizing flame burns an excess of acetylene, which shows as a feather around the inner cone, and too much of it adds carbon to the metal. An oxidizing flame burns an excess of oxygen, about 2 parts to 1 of acetylene, and shows a shorter outer flame and a small white inner cone.

Q.03

What is a carburizing flame used for?

Welding high-carbon steels, hard facing, and welding nonferrous alloys such as aluminum, nickel and Monel. A slight excess of acetylene is also used on stainless steel and other alloys high in nickel or chromium, while most steels take an exactly neutral flame.

Q.04

What does a good weld look like?

A smooth seam with evenly spaced ripples and a uniform thickness, built up slightly convex, tapering smoothly into the base metal, with no oxide on the metal beside it, no blowholes, porosity or globules, and no burns, pits, cracks or distortion in the base metal. A smooth weld can still be weak inside, though.

Q.05

How many aircraft welding questions are on the FAA A&P Airframe test?

The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Metallic Structures subject area 5 to 15% of the Airframe test, which is 5 to 15 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.

Q.06

Which FAA handbook chapter covers aircraft welding?

Chapter 5 of FAA-H-8083-31B, the Aviation Maintenance Technician Handbook: Airframe, titled "Aircraft Welding". It runs from pages 5-1 to 5-35, and the FAA publishes the whole handbook free as a PDF.

FREE PLAN · NO CARD · 25 QUESTIONS TO START

The bank holds 245 aircraft welding questions.

Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.

Start free

Or answer a few first. The free FAA A&P practice test runs on the page, with no account.