PrepAMT Academy

AMA · AF-01 · FAA-H-8083-31B CH. 1

FAA A&P Airframe: Aircraft Structures

For the FAA A&P Airframe test, aircraft structures is chapter 1 of FAA-H-8083-31B, Aircraft Structures. Its main ACS subject area, Metallic Structures, is 5 to 15% of the test, or 5 to 15 of its 100 scored questions. Our question bank holds 327 questions on it, and the 10 below were written for this page.

Test shares and most-missed codes read from the FAA on 15 November 2026.

01 WHAT IT COVERSFAA-H-8083-31B · CH. 1

What FAA-H-8083-31B chapter 1 covers

Chapter 1 starts with how aircraft construction developed and the 5 stresses a structure has to carry. It then works through the fixed-wing airframe: fuselage construction, truss, monocoque and semimonocoque; pressurization; wings with their spars, ribs and skins; nacelles; the empennage; and the flight control surfaces, from ailerons, elevators and rudders to flaps, spoilers, slats and tabs.

It also covers landing gear, skins, fairings and access panels, the station numbering that locates any point on the airframe, and helicopter structures: the airframe, the flight controls, the rotor systems and the transmission.

It runs from pages 1-1 to 1-45 of the Aviation Maintenance Technician Handbook: Airframe, which the FAA publishes free as a PDF.

02 SHARE OF THE TESTFAA-G-ACS-1 · BLUEPRINT

How much of the FAA A&P Airframe test it is

  • 5 to 15%OF THE TESTACS area AM.II.A
  • 5 to 15QUESTIONSof 100 scored
  • 327IN OUR BANKquestions on this subject

The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Metallic Structures (AM.II.A) is 5 to 15% (5 to 15 questions) on the 100-question Airframe test. Our Aircraft Structures questions also reach into Non-Metallic Structures (AM.II.B, 5 to 10%), Flight Controls (AM.II.C, 5 to 10%) and Rotorcraft Fundamentals (AM.II.N, 5 to 10%). The 15 ranges for the Airframe test add up to anywhere from 75% to 160%, so they say how big an area can get, not how many questions you will see from it.

Metallic Structures is not ours alone to cover: our Aircraft Metal Structural Repair, Aircraft Welding and Aircraft Painting and Finishing questions are written to the same area.

No code in these areas is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.

03 EXAMPLE QUESTIONSWRITTEN FOR THIS PAGE

Aircraft structures questions and answers

10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.

  1. Q.01

    An airplane's propeller is not counted as part of its airframe. Why are the main rotor blades of a helicopter counted as part of the airframe?

    FAA-H-8083-31B, ch. 1, p. 1-5

    1. AThey are rotating wings that make the lift, as a fixed wing does
    2. BThey are driven through the transmission, not bolted to the engine
    3. CThey are built of the same composite as the fuselage and tail boom
    SHOW THE ANSWER

    THE ANSWER IS A.

    They are rotating wings that make the lift, as a fixed wing does

    The airframe takes in the fuselage, booms, nacelles, airfoil surfaces and landing gear. A helicopter's rotor blades are rotating wings that produce its lift, so they belong to the airframe. A propeller or the rotating airfoils inside an engine are not part of it. Being driven through a gearbox does not decide it, since many propellers are geared too, and neither does what the blades are made of.

  2. Q.02

    A light airplane model is offered with either tail wheel gear or tricycle gear. Why does the tail wheel version usually have the lighter landing gear?

    FAA-H-8083-31B, ch. 1, p. 1-36

    1. AIts main wheels carry only a small share of the weight, so they can be built light
    2. BIts main gear needs no shock absorbing, since the tail wheel takes the landing loads
    3. CTricycle gear needs a stout nose wheel assembly that fully absorbs shock
    SHOW THE ANSWER

    THE ANSWER IS C.

    Tricycle gear needs a stout nose wheel assembly that fully absorbs shock

    Tail wheel gear has 2 main wheels that take most of the airplane's weight, plus a small tail wheel that does little more than keep the aft fuselage off the ground. Tricycle gear moves the third wheel to the nose, and that nose wheel assembly has to be stout and fully shock absorbing, so the tail wheel arrangement usually weighs less. On either arrangement the main gear carries most of the weight and is built to absorb landing shock.

  3. Q.03

    During World War II, deep fuel-carrying wings were the norm. Why did some designs of that time carry their fuel in the fuselage instead?

    FAA-H-8083-31B, ch. 1, p. 1-3

    1. AFuel in the wings was too hard to reach for refueling
    2. BTheir thin wings, built for higher speed, had little room for it
    3. CWing tanks were banned after early fires in combat
    SHOW THE ANSWER

    THE ANSWER IS B.

    Their thin wings, built for higher speed, had little room for it

    All-metal designs of the war years mostly carried fuel in deep wings. The push for higher flight speeds brought thin-winged aircraft, and a thin wing leaves little space for tanks, so those designs carried their fuel in the fuselage. Refueling access and any ban on wing tanks had nothing to do with it; deep wing tanks stayed the norm.

  4. Q.04

    An amphibian uses the bottom half of its fuselage as a hull. What are the small floats under its wings, out near the tips, there for?

    FAA-H-8083-31B, ch. 1, p. 1-34

    1. ATo carry fuel that will not fit inside the wings
    2. BTo lift the hull clear of the water at takeoff speed
    3. CTo aid it in landing and taxiing on the water
    SHOW THE ANSWER

    THE ANSWER IS C.

    To aid it in landing and taxiing on the water

    On some amphibians the bottom half of the fuselage acts as the hull, and outriggers on the underside of the wings near the tips go with it to aid the airplane in water landing and taxi. That is their job: they are small floats, not fuel tanks, and it is the hull that carries the airplane on the water. Main gear that retract into the fuselage are only lowered for landing on a runway.

  5. Q.05

    You inspect 2 pressurized airplanes of the same model with the same total hours. One has flown many short trips, the other far fewer long ones. Why does the short-trip airplane's fuselage deserve the closer look?

    FAA-H-8083-31B, ch. 1, p. 1-9

    1. AIt has been through many more pressurization cycles, and each one adds metal fatigue
    2. BIt has spent more of its hours pressurized, and time at pressure is what fatigues metal
    3. CIts cabin is held at a higher pressure difference on short trips than on long ones
    SHOW THE ANSWER

    THE ANSWER IS A.

    It has been through many more pressurization cycles, and each one adds metal fatigue

    Every flight takes the fuselage from unpressurized to pressurized and back again, and that cycling is what causes metal fatigue, on top of the pressure difference the structure has to hold. Many short trips mean many more cycles in the same hours. The short-trip airplane has in fact spent less of its time at full pressure, and a short trip flown lower calls for a smaller cabin pressure difference, not a bigger one. That is why pressurized fuselages get extensive periodic inspections.

  6. Q.06

    On a test flight in a transport whose spoilers help the ailerons with roll at low speed, the spoilers stop moving with the control wheel once speed builds. If the system is working as designed, why?

    FAA-H-8083-31B, ch. 1, p. 1-29

    1. AThe spoiler interconnect disengages, since the ailerons alone are effective enough
    2. BThe speed brakes have been selected, which holds every spoiler flat on the wing
    3. CAir loads have stalled the spoiler actuators, which is a fault to be written up
    SHOW THE ANSWER

    THE ANSWER IS A.

    The spoiler interconnect disengages, since the ailerons alone are effective enough

    At low speed the spoilers work with the ailerons: on the wing whose aileron goes up, the spoilers rise too and add to the loss of lift there, while those on the other wing stay stowed. As speed increases the ailerons become more effective and the spoiler interconnect disengages, so spoilers that stop following the wheel at speed are doing what the design intends. Selecting speed brakes raises the spoilers on both wings rather than holding them flat.

  7. Q.07

    You are about to inspect a conventional-gear airplane that has no tail wheel at all. What should you expect to find under its aft fuselage?

    FAA-H-8083-31B, ch. 1, p. 1-35

    1. AA rubber tail bumper that also takes the landing loads
    2. BA steel skid plate that the tail rests on
    3. CA tail stand that is fitted before every flight
    SHOW THE ANSWER

    THE ANSWER IS B.

    A steel skid plate that the tail rests on

    Conventional gear puts 2 main wheels under most of the weight and a small wheel at the aft end of the fuselage. Some conventional-gear airplanes have no tail wheel at all and use just a steel skid plate under the aft fuselage instead. Either one lets the fuselage sit inclined, which gave clearance for the long propellers of the past. A tail stand is ground equipment, and a rubber bumper is not what the handbook describes.

  8. Q.08

    You take over a helicopter whose main rotor has elastomeric bearings where the older model you know had steel bearings. Which routine task does that change remove?

    FAA-H-8083-31B, ch. 1, p. 1-44

    1. AGreasing the rotor bearings at set intervals
    2. BTracking the blades after one is changed
    3. CChecking the rotor's vibration level in flight
    SHOW THE ANSWER

    THE ANSWER IS A.

    Greasing the rotor bearings at set intervals

    Elastomeric bearings are polymer bearings that deform under load and then return to their original shape. They absorb vibration that steel bearings would pass on, and they do not need regular lubrication, which reduces maintenance. They do nothing to remove the need to track the blades after a change, and absorbing some vibration is not the same as removing the causes a vibration check looks for.

  9. Q.09

    A skin doubler on the belly runs across the centerline, from butt line 16.00 on the left side to butt line 23.25 on the right side. How wide is the doubler?

    FAA-H-8083-31B, ch. 1, p. 1-37

    1. A7.25 inches
    2. B39.25 inches
    3. C46.50 inches
    SHOW THE ANSWER

    THE ANSWER IS B.

    39.25 inches

    The butt line is a vertical reference plane down the center of the aircraft, and butt line numbers give the distance in inches to its left or right. A part that crosses the centerline spans both distances, so its width is 16.00 plus 23.25, which is 39.25 inches. Subtracting the 2 numbers gives 7.25, which only works when both points are on the same side, and 46.50 wrongly treats the doubler as reaching 23.25 inches each way.

  10. Q.10

    Before a skin repair on a monocoque fuselage, you study its frame layout. Most of the formers and bulkheads are light, but a few are much heavier. Where should you expect those heavy ones to be?

    FAA-H-8083-31B, ch. 1, p. 1-8

    1. AIn the tail cone, which is built heavier than the rest of the fuselage
    2. BBetween the attach fittings, so the fittings can sit on light structure
    3. CAt the fittings that attach the wings, powerplant and stabilizers
    SHOW THE ANSWER

    THE ANSWER IS C.

    At the fittings that attach the wings, powerplant and stabilizers

    In a true monocoque fuselage, formers, frame assemblies and bulkheads give the shape, and with no other bracing members the skin carries the primary stresses. The heaviest of those members are placed at intervals to carry concentrated loads, and at the points where fittings attach other units such as the wings, powerplant and stabilizers. A fitting needs heavy structure behind it, not light. The tail cone is the opposite case: it is usually built lighter than the fuselage, because it receives less stress.

We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.

04 AND THEN THE ORAL§ 65.79

How a missed code comes back at the oral

Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.II.A or AM.II.B or AM.II.C or AM.II.N. The examiner reads those codes before your oral and practical.

The Airframe oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Airframe also carries 11 practical projects, each with 2 questions attached.

Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.

05 COMMON QUESTIONSFAQ

Questions people ask about aircraft structures

Q.01

What are the 5 stresses on an aircraft structure?

Tension, which pulls a member apart; compression, which squeezes it; torsion, which twists it; shear, which makes the layers of a material slide over each other; and bending, which is tension on one side of a member and compression on the other.

Q.02

What is the difference between monocoque and semimonocoque construction?

A monocoque fuselage carries its primary loads in its skin, with formers and bulkheads giving it shape, so the hard part is making it strong enough without making it too heavy. A semimonocoque fuselage adds longerons and stringers, so the skin and the framework share the load, which is how most modern aircraft are built.

Q.03

What is a trim tab for?

It is usually a small hinged surface on the trailing edge of a primary control surface. Set by the pilot, it holds the main surface where it needs to be to keep the aircraft in trim, so the pilot does not have to hold pressure on the controls. Some light aircraft have a fixed metal tab instead, bent on the ground.

Q.04

What is a fuselage station?

A distance in inches, measured along the length of the aircraft from a zero point near the nose. Together with a buttock line, measured left or right of the centerline, and a water line, measured up from a reference plane, it locates any point on the airframe.

Q.05

How many aircraft structures questions are on the FAA A&P Airframe test?

The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Metallic Structures subject area 5 to 15% of the Airframe test, which is 5 to 15 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it. Our Aircraft Structures questions also reach into Non-Metallic Structures (5 to 10%), Flight Controls (5 to 10%) and Rotorcraft Fundamentals (5 to 10%).

Q.06

Which FAA handbook chapter covers aircraft structures?

Chapter 1 of FAA-H-8083-31B, the Aviation Maintenance Technician Handbook: Airframe, titled "Aircraft Structures". It runs from pages 1-1 to 1-45, and the FAA publishes the whole handbook free as a PDF.

FREE PLAN · NO CARD · 25 QUESTIONS TO START

The bank holds 327 aircraft structures questions.

Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.

Start free

Or answer a few first. The free FAA A&P practice test runs on the page, with no account.