AMA · AF-08 · FAA-H-8083-31B CH. 8
FAA A&P Airframe: Aircraft Painting and Finishing
For the FAA A&P Airframe test, aircraft painting and finishing is chapter 8 of FAA-H-8083-31B, Aircraft Painting & Finishing. Its main ACS subject area, Metallic Structures, is 5 to 15% of the test, or 5 to 15 of its 100 scored questions. Our question bank holds 183 questions on it, and the 10 below were written for this page.
Test shares and most-missed codes read from the FAA on 15 November 2026.
What FAA-H-8083-31B chapter 8 covers
Chapter 8 covers the materials of a finish, the thinners and solvents, the primers from wash primer to epoxy primer, and the topcoats such as polyurethane. It covers the equipment, spray guns, air supplies and the protection a painter needs, and how to prepare a surface and apply a finish.
It also covers the common finish defects and what causes them, such as orange peel, fish eyes, runs, sags and blushing, and the trim, registration marks and decals the finish carries.
It runs from pages 8-1 to 8-21 of the Aviation Maintenance Technician Handbook: Airframe, which the FAA publishes free as a PDF.
How much of the FAA A&P Airframe test it is
- 5 to 15%OF THE TESTACS area AM.II.A
- 5 to 15QUESTIONSof 100 scored
- 183IN OUR BANKquestions on this subject
The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Metallic Structures (AM.II.A) is 5 to 15% (5 to 15 questions) on the 100-question Airframe test. Our Aircraft Painting and Finishing questions also reach into Non-Metallic Structures (AM.II.B, 5 to 10%). The 15 ranges for the Airframe test add up to anywhere from 75% to 160%, so they say how big an area can get, not how many questions you will see from it.
Metallic Structures is not ours alone to cover: our Aircraft Structures, Aircraft Metal Structural Repair and Aircraft Welding questions are written to the same area.
No code in these areas is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.
Aircraft painting and finishing questions and answers
10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.
- Q.01
A can in the paint shop is labeled boiled linseed oil. What does the word boiled tell you about the oil inside?
FAA-H-8083-31B, ch. 8, p. 8-2
- AIt was heated until it can no longer catch fire on its own
- BIt was pressed from the seed without the solvent extraction step
- CIt was processed with additives to shorten its drying time
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
It was processed with additives to shorten its drying time
Linseed oil is pressed from dried flax seed and then put through solvent extraction; oil made without that step is sold as flaxseed oil. Boiled linseed oil has been processed with additives so that it dries faster. It still carries the warning about fire from spontaneous combustion, because the oil gives off heat as it dries, so oily rags must still be disposed of properly.
- Q.02
Before masking a personal paint scheme, the handbook suggests drawing it on a silhouette of the airplane, as close to scale as you can. Why?
FAA-H-8083-31B, ch. 8, p. 8-15
- AA drawing is much easier to change than remasking the airplane
- BThe FAA has to approve the drawing before any new trim is painted
- CThe drawing lets the trim be sprayed without any masking tape
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
A drawing is much easier to change than remasking the airplane
A personal scheme is worked out first on a silhouette drawing of the aircraft, kept as close to scale as possible, because it is much easier to change a drawing than to remask the aircraft. The handbook ties no FAA approval to a trim design; the rules it gives are for the registration marks. The drawing does not replace the masking either: the trim lines are still laid out with Fine Line tape and looked over before anything is sprayed.
- Q.03
Why does the handbook recommend protective clothing such as Tyvek coveralls for anyone spraying paint on an aircraft?
FAA-H-8083-31B, ch. 8, p. 8-21
- AThey take the place of a respirator inside the paint booth
- BThey protect the painter and also help keep dust off the new paint
- CThey let the painter handle stripper safely without gloves on
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
They protect the painter and also help keep dust off the new paint
Protective clothing such as Tyvek coveralls does 2 jobs: it protects the painter from the paint, and it helps keep dust off the painted surfaces. It is no substitute for breathing protection, which comes from a proper respirator or a fresh air system, and rubber gloves must still be worn whenever stripper, etching solution, conversion coating or solvent is used.
- Q.04
Partway through spraying a coat, you notice pinholes forming in the finish. What should you do?
FAA-H-8083-31B, ch. 8, p. 8-13
- AStop and look over your equipment and spraying technique before going on
- BKeep spraying, and bury the pinholes under one heavier, wetter final coat
- CAdd fisheye eliminator to the next coats and carry straight on
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Stop and look over your equipment and spraying technique before going on
Pinholes are trapped solvent, air or moisture, and they come from contaminated air lines or paint and from coats put on too heavy and wet. So when they appear, the equipment and the painting technique are checked before going any further, and once the coat is dry the surface is sanded smooth and repainted. A heavier coat is one of the causes, not a cure, and fisheye eliminator is for the occasional fisheye, not for pinholes.
- Q.05
Halfway through spraying a panel, lots of small craters open up in the wet paint and show the surface underneath. What should you do?
FAA-H-8083-31B, ch. 8, p. 8-14
- AKeep spraying heavier coats until the craters fill in
- BStop, wipe off the wet paint and clean off all the silicone
- CLet the coat dry, then sand it and spray on with a slow reducer
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Stop, wipe off the wet paint and clean off all the silicone
Those craters are fisheyes, and they usually come from silicone wax left on the surface. When lots of them appear, stop spraying, clean off all the wet paint and take off every trace of silicone with a silicone wax remover. Heavier coats will not bury them, and letting the coat dry, sanding it and respraying with a slow reducer leaves the silicone where it is. A water break test before painting shows whether a surface is clean: the water should lie in an unbroken film instead of beading.
- Q.06
A second heavy coat went on before the first had dried, and the finish has wrinkled across a whole panel. What has to be done?
FAA-H-8083-31B, ch. 8, p. 8-15
- ALet it cure fully, then buff the wrinkles out with compound
- BSand the high spots and spray a light coat to fill the low ones
- CRemove the wrinkled paint completely and refinish the surface
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Remove the wrinkled paint completely and refinish the surface
Wrinkling comes from solvents trapped under a surface that dried first, as when a heavy coat goes on over one that has not dried, and it can even lift the coat underneath. Wrinkled paint must be completely removed and the surface refinished. Buffing, or sanding and a light coat, only deal with faults on the surface such as light orange peel or spray dust, and they leave the trapped solvent where it is.
- Q.07
You have masked a trim stripe with Fine Line tape over the cured base color. What can you spray first, just before the trim color, to get a clean, sharp line when the tape comes off?
FAA-H-8083-31B, ch. 8, p. 8-16
- AA light coat of the base color or clear, to seal the tape edge
- BA heavy coat of the trim color, so it bridges the tape edge
- CA coat of wash primer along the tape line, so the trim bites
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
A light coat of the base color or clear, to seal the tape edge
Some painters spray a light coat of the base color or a clear coat just before the trim color. It seals the edge of the Fine Line tape, so the line comes out clean and sharp when the tape is pulled. A heavy coat is what causes sags and runs, and wash primer is a first coat that passivates bare metal; it does nothing to seal a tape edge on a cured topcoat.
- Q.08
Your Zahn cup test shows a topcoat a little thicker than the data sheet asks for. As you add reducer to bring it in, what limit must you keep to?
FAA-H-8083-31B, ch. 8, p. 8-9
- AAdd reducer until the cup drains about twice as fast as the data sheet says
- BDo not thin it below the maker's recommendation, or too many VOCs are released
- CThin it as far as you like, since extra reducer only makes the paint go on smoother
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Do not thin it below the maker's recommendation, or too many VOCs are released
The efflux time is compared with the coating maker's figure and the viscosity adjusted if it needs it, but the coating must not be thinned below the recommendation, because that can release VOCs into the air above the regulated limits. Too much reducer also leaves the paint too thin, which is one of the causes of sags and runs, so a cup that drains far faster than the figure is wrong as well.
- Q.09
A painter new to the spray gun has mastered a flat, horizontal test panel. What does the handbook say should come before painting the airplane itself?
FAA-H-8083-31B, ch. 8, p. 8-12
- ANothing more, since a good horizontal panel shows the skill is there
- BA first coat on the airplane's belly, where small faults will not show
- CPractice on a vertical panel until it gives a smooth, glossy coat with no runs
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Practice on a vertical panel until it gives a smooth, glossy coat with no runs
A flat horizontal panel is only the first step. The handbook says to practice next on a panel standing vertically against a wall, and only when that gives a smooth, glossy application with no runs is the painter ready for the actual project. Vertical surfaces are where sags and runs show up, which is why they get practice of their own, and the airplane itself is never the practice panel.
- Q.10
Sanding scratches have shown up in a fresh topcoat on a fiberglass fairing that was properly sanded and sealed first. What else can cause them?
FAA-H-8083-31B, ch. 8, p. 8-14
- AAn overly fast, quick-drying thinner in the topcoat
- BSpraying the topcoat when the humidity is above 80 percent
- CLeaving the paint on the shaker too long before use
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
An overly fast, quick-drying thinner in the topcoat
Sanding scratches show in the finish when the surface was not properly sanded or sealed before the finish coats, which is common on nonmetal parts such as composite cowlings, wood and plastic fairings. With the sanding and sealing done right, the other cause the handbook gives is an overly rapid, quick-drying thinner. Humidity above 80 percent is when blushing, a dull milky haze, usually forms, not scratches, and the paint shaker is there to mix the coating.
We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.
How a missed code comes back at the oral
Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.II.A or AM.II.B. The examiner reads those codes before your oral and practical.
The Airframe oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Airframe also carries 11 practical projects, each with 2 questions attached.
Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.
Questions people ask about aircraft painting and finishing
Q.01What causes orange peel in a paint finish?
A bumpy surface, like the skin of an orange. The first cause to check is a spray gun that is not adjusted properly. Others are paint mixed too thick or with the wrong reducer for the temperature, paint not mixed evenly, and drying it too fast with fans or heat.
Q.02What causes fish eyes in paint?
Contamination on the surface, silicone above all, that the paint will not wet. The answer is a surface that is clean of every kind of contamination before painting, and a water break test shows whether it is: if water beads up anywhere, the surface is not clean.
Q.03How high must registration marks be on an airplane?
For almost every US registered, standard certificated, fixed-wing aircraft, the marks must be at least 12 inches high, all the same height, and 2/3 as wide as they are high, apart from M, W and the digit 1. A glider may carry marks 3 inches high.
Q.04What is blushing in a paint finish?
A dull, milky haze in a paint finish, from moisture trapped in the paint. The solvents evaporate quickly from the sprayed coat, the temperature of the surface drops, and moisture in the air condenses in the wet paint. A slow drying reducer can help.
Q.05How many aircraft painting and finishing questions are on the FAA A&P Airframe test?
The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Metallic Structures subject area 5 to 15% of the Airframe test, which is 5 to 15 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it. Our Aircraft Painting and Finishing questions also reach into Non-Metallic Structures (5 to 10%).
Q.06Which FAA handbook chapter covers aircraft painting and finishing?
Chapter 8 of FAA-H-8083-31B, the Aviation Maintenance Technician Handbook: Airframe, titled "Aircraft Painting & Finishing". It runs from pages 8-1 to 8-21, and the FAA publishes the whole handbook free as a PDF.
Read the documents, not us
Every fact on this page was read from these on 19 August 2026 and 15 November 2026. They are the authority and we are the summary. If we and one of them disagree, they are right.
- FAA-H-8083-31B, Aviation Maintenance Technician Handbook: Airframe, chapter 8www.faa.gov
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standardswww.faa.gov
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards: the written test blueprints (pages 13 and 14) and chapters 6 and 7www.faa.gov
- FAA, Frequently Missed Knowledge Test ACS Codes, 2nd Quarter CY25www.faa.gov
FREE PLAN · NO CARD · 25 QUESTIONS TO START
The bank holds 183 aircraft painting and finishing questions.
Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.
Start freeOr answer a few first. The free FAA A&P practice test runs on the page, with no account.