AMA · AF-07 · FAA-H-8083-31B CH. 7
FAA A&P Airframe: Advanced Composite Materials
For the FAA A&P Airframe test, advanced composite materials is chapter 7 of FAA-H-8083-31B, Advanced Composite Materials. Its ACS subject area, Non-Metallic Structures, is 5 to 10% of the test, or 5 to 10 of its 100 scored questions. Our question bank holds 296 questions on it, and the 10 below were written for this page.
Test shares and most-missed codes read from the FAA on 15 November 2026.
What FAA-H-8083-31B chapter 7 covers
Chapter 7 covers what composites are and why aircraft use them: the fibers, fiberglass, aramid and carbon; the resins that hold them; prepreg; sandwich construction with honeycomb and foam cores; and how parts are laid up and cured under vacuum bags, heat blankets and autoclaves.
It then covers inspecting composites, from tap testing to ultrasonic methods, the damage they take, and repairs: core and skin repairs, bonded scarf repairs, and the fasteners used in composite structure, along with the safety precautions for working with these materials.
It runs from pages 7-1 to 7-58 of the Aviation Maintenance Technician Handbook: Airframe, which the FAA publishes free as a PDF.
How much of the FAA A&P Airframe test it is
- 5 to 10%OF THE TESTACS area AM.II.B
- 5 to 10QUESTIONSof 100 scored
- 296IN OUR BANKquestions on this subject
The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Non-Metallic Structures (AM.II.B) is 5 to 10% (5 to 10 questions) on the 100-question Airframe test. The 15 ranges for the Airframe test add up to anywhere from 75% to 160%, so they say how big an area can get, not how many questions you will see from it.
Non-Metallic Structures is not ours alone to cover: our Aircraft Structures, Aircraft Fabric Covering, Aircraft Wood Structural Repair and Aircraft Painting and Finishing questions are written to the same area.
No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.
Advanced composite materials questions and answers
10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.
- Q.01
Some film adhesives carry a woven cloth inside them to help control the bond line thickness. What drawback can that cloth bring?
FAA-H-8083-31B, ch. 7, p. 7-9
- AIt carries heat away, so the film cannot reach its cure temperature
- BIts fibers can wick water, which slightly degrades environmental properties
- CIt shrinks during the cure and pulls the bonded parts out of line
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Its fibers can wick water, which slightly degrades environmental properties
Film adhesives are often supported by fibers, as short random mats or as woven cloth, to help handling, control the flow during bonding and control the bond line thickness. Common fibers are polyester, nylon and glass. The trade-off the handbook names is that adhesives containing woven cloth may have slightly degraded environmental properties, because the fibers can wick water. It names no loss of cure heat and no shrinkage from the cloth.
- Q.02
Vinyl ester resin looks, handles and cures much like a standard polyester resin. Why would you choose it over polyester?
FAA-H-8083-31B, ch. 7, p. 7-6
- AIt cures in a fraction of the time at room temperature
- BIt gives off less smoke, so it suits cabin interior parts
- CIt gives better corrosion resistance and mechanical properties
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
It gives better corrosion resistance and mechanical properties
Vinyl ester has the same appearance, handling and curing as a conventional polyester, so it does not cure any faster. What it adds is much better corrosion resistance and mechanical properties in the finished composite. Low smoke is the reason low-smoke polyester and phenolic resins go into cabin interiors, not the reason to pick vinyl ester.
- Q.03
A broken acrylic part is to serve as the mold for a plaster forming block. Once you have taped the pieces together, what comes next before the plaster goes in?
FAA-H-8083-31B, ch. 7, p. 7-54
- AWax or grease the inside, then support the whole part in sand
- BHeat the part until it softens, so the plaster fills every curve
- CWet the inside with water so the plaster flows and sets evenly
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Wax or grease the inside, then support the whole part in sand
A damaged part can be the mold for the form its replacement is shaped on. If it is broken, the pieces are taped together, the inside is waxed or greased so the plaster does not stick to it, and the whole part is supported in sand. It is then filled with plaster, left to harden and removed, and the form is smoothed and covered with soft cloth. Heating the old part would distort the very shape being copied, and water does nothing to stop the plaster sticking.
- Q.04
You have been cutting aramid prepreg with scissors that have one serrated blade. What should you do with the scissors as soon as you finish?
FAA-H-8083-31B, ch. 7, p. 7-52
- ALeave the resin to cure on the blade, then chip it off later
- BClean the serrations at once, before the uncured resin can ruin them
- CGrind the serrations smooth so the next cut does not fuzz the fibers
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Clean the serrations at once, before the uncured resin can ruin them
Scissors for aramid fabric or prepreg have a shearing edge on one blade and a serrated or grooved surface on the other, and the serrations hold the material so it does not slip. Uncured resin left in them would ruin the scissors, so the handbook says to clean the serrations immediately after use. Letting the resin cure first is exactly what spoils them, and grinding the serrations away removes what keeps the fabric from slipping.
- Q.05
Your shop is sending part of a roll of prepreg from its freezer to another repair station. How should the prepreg travel?
FAA-H-8083-31B, ch. 7, p. 7-26
- AThawed first, then sealed in its bag at room temperature
- BIn a cooler with ordinary ice, kept near 40 °F like paste adhesive
- CIn a special container filled with dry ice
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
In a special container filled with dry ice
Prepreg, film adhesive and foaming adhesive live in a freezer below 0 °F, and when they have to be shipped they go in special containers filled with dry ice. Thawing the roll for the trip spends its life for nothing, because the mechanical life is counted from the moment the material leaves the freezer until it goes back in. Near 40 °F is refrigerator storage, which is meant for laminating and paste adhesives, not for prepreg.
- Q.06
You are impregnating repair fabric inside a vacuum bag. The resin is poured, the bag is sealed and the vacuum is on. What do you do before sweeping the resin into the fabric?
FAA-H-8083-31B, ch. 7, p. 7-31
- AWait about 2 minutes for the air to come out of the fabric
- BVent the bag so the resin can flow freely into the weave
- CWarm the bag to 250 °F so the resin thins before you sweep it
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Wait about 2 minutes for the air to come out of the fabric
Once the bag is sealed and the vacuum is on, allow about 2 minutes for the air to be drawn out of the fabric, then sweep the resin slowly from the center out to the edges with a squeegee. Venting the bag throws away the vacuum that keeps air out of the weave, and heat speeds up the cure, which is the last thing you want before the plies are even cut.
- Q.07
You are heating acrylic sheets in an oven before forming them. How should the sheets be held so they heat evenly?
FAA-H-8083-31B, ch. 7, p. 7-54
- ALaid flat on a bare metal shelf so the heat spreads through them
- BHung vertically from their edges with spring clips on a rack
- CStacked together so that they hold each other's heat
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Hung vertically from their edges with spring clips on a rack
For uniform heating, acrylic sheets are best hung vertically, held by their edges with spring clips that hang from a rack. A piece too small to clip, or with too little trim area, is laid on a shelf or rack covered with soft felt or flannel rather than bare metal, and sheets are not stacked. If the plastic gets too hot, bubbles can form on the surface and spoil its optical quality.
- Q.08
You are shaping an airfoil from polypropylene foam, and the kit came with polyester resin for the skin. What should you do?
FAA-H-8083-31B, ch. 7, p. 7-12
- AGo ahead, since polypropylene works with every common resin
- BWipe the foam with solvent first so the polyester grips it
- CSwitch to an epoxy resin, which suits polypropylene
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Switch to an epoxy resin, which suits polypropylene
Polypropylene foam can be cut with a hot wire and works with most adhesives and epoxy resins, but it is not for use with polyester resins, so the skin goes on with an epoxy. It also dissolves in fuels and solvents, so wiping it with solvent would eat into the core instead of helping the bond.
- Q.09
Composites are used in many places on aircraft. Why has their use on leading-edge surfaces generally been avoided?
FAA-H-8083-31B, ch. 7, p. 7-14
- AThey have stood up to erosion less well than aluminum
- BThey cannot be formed to the tight curve of a leading edge
- CThey pass deice boot heat through too slowly
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
They have stood up to erosion less well than aluminum
Composite materials have been known to resist erosion less well than aluminum, and for that reason their use on leading-edge surfaces has generally been avoided. Composites are in fact used where the shape is highly complex, usually with an erosion coating, so forming the curve is not the problem, and deice boots have nothing to do with the choice.
- Q.10
A heat bonder ramps a repair from 75 °F up to a 250 °F cure at 5 °F per minute. How long does the ramp up take?
FAA-H-8083-31B, ch. 7, p. 7-33
- A50 minutes
- B35 minutes
- C15 minutes
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
35 minutes
The rise is 250 minus 75, which is 175 °F. At 5 °F a minute that takes 175 divided by 5, or 35 minutes. Dividing 250 by 5 gives 50 minutes, as if the part started at 0 °F, and 15 minutes is just 75 divided by 5. Typical ramp rates run from 3 °F to 5 °F a minute, so the slower 3 °F rate would take nearer an hour.
We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.
How a missed code comes back at the oral
Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.II.B. The examiner reads those codes before your oral and practical.
The Airframe oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Airframe also carries 11 practical projects, each with 2 questions attached.
Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.
Questions people ask about advanced composite materials
Q.01What is a tap test on a composite part?
Tapping the area with a solid round disc or a light hammer-like tool and listening. A delamination or disbond changes the sound. It works on thin skins bonded to stiffeners, honeycomb with thin face sheets, and near the surface of thick laminates, but not deep inside them.
Q.02What is prepreg?
Fabric that comes already impregnated with resin, with the resin partly cured. It is stored in a freezer, at 0 degrees F or below, to hold the resin at that stage, and the cure starts again once it is taken out and warmed.
Q.03What is the difference between E-glass and S-glass?
E-glass, electrical glass, was named for electrical uses because it resists the flow of current. S-glass and S2-glass are structural fiberglass, with a higher strength than E-glass.
Q.04Why must a composite repair match the original ply orientation?
Because a composite part is strong along its fibers, and each ply was laid at the angle that carries the load in that direction. A repair ply laid at the wrong angle leaves the part weak in the direction it was built to be strong.
Q.05How many advanced composite materials questions are on the FAA A&P Airframe test?
The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Non-Metallic Structures subject area 5 to 10% of the Airframe test, which is 5 to 10 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.
Q.06Which FAA handbook chapter covers advanced composite materials?
Chapter 7 of FAA-H-8083-31B, the Aviation Maintenance Technician Handbook: Airframe, titled "Advanced Composite Materials". It runs from pages 7-1 to 7-58, and the FAA publishes the whole handbook free as a PDF.
Read the documents, not us
Every fact on this page was read from these on 19 August 2026 and 15 November 2026. They are the authority and we are the summary. If we and one of them disagree, they are right.
- FAA-H-8083-31B, Aviation Maintenance Technician Handbook: Airframe, chapter 7www.faa.gov
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standardswww.faa.gov
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards: the written test blueprints (pages 13 and 14) and chapters 6 and 7www.faa.gov
- FAA, Frequently Missed Knowledge Test ACS Codes, 2nd Quarter CY25www.faa.gov
More FAA A&P Airframe subjects
FREE PLAN · NO CARD · 25 QUESTIONS TO START
The bank holds 296 advanced composite materials questions.
Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.
Start freeOr answer a few first. The free FAA A&P practice test runs on the page, with no account.