AMA · AF-03 · FAA-H-8083-31B CH. 3
FAA A&P Airframe: Aircraft Fabric Covering
For the FAA A&P Airframe test, aircraft fabric covering is chapter 3 of FAA-H-8083-31B, Aircraft Fabric Covering. Its ACS subject area, Non-Metallic Structures, is 5 to 10% of the test, or 5 to 10 of its 100 scored questions. Our question bank holds 232 questions on it, and the 10 below were written for this page.
Test shares and most-missed codes read from the FAA on 15 November 2026.
What FAA-H-8083-31B chapter 3 covers
Chapter 3 covers fabric covered aircraft: the history, the words of the trade such as warp, fill, selvage edge and bias, the fabrics approved today, and the covering processes, which are nearly all polyester fabric under a supplemental type certificate.
It walks through covering a structure by the envelope or blanket method, attaching the fabric with rib lacing, stitches, rivets or clips, heat shrinking it, coating and taping it, then inspecting and testing the fabric’s strength and making repairs.
It runs from pages 3-1 to 3-24 of the Aviation Maintenance Technician Handbook: Airframe, which the FAA publishes free as a PDF.
How much of the FAA A&P Airframe test it is
- 5 to 10%OF THE TESTACS area AM.II.B
- 5 to 10QUESTIONSof 100 scored
- 232IN OUR BANKquestions on this subject
The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Non-Metallic Structures (AM.II.B) is 5 to 10% (5 to 10 questions) on the 100-question Airframe test. The 15 ranges for the Airframe test add up to anywhere from 75% to 160%, so they say how big an area can get, not how many questions you will see from it.
Non-Metallic Structures is not ours alone to cover: our Aircraft Structures, Aircraft Wood Structural Repair, Advanced Composite Materials and Aircraft Painting and Finishing questions are written to the same area.
No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.
Aircraft fabric covering questions and answers
10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.
- Q.01
Partway along a wing rib, the lacing cord you are using runs out. Which of these is an accepted way to carry on?
FAA-H-8083-31B, ch. 3, p. 3-19
- ASeal the remaining holes with cement and cover them with finishing tape
- BEnd the cord there and start a new length with a starting knot at the next holes
- CPull the last stitch extra tight so it holds the rest of the rib on its own
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
End the cord there and start a new length with a starting knot at the next holes
Lacing that is not long enough to finish a rib may be ended, and a new length started with a starting knot at the next set of holes. It can also be lengthened by joining another piece on with a splice knot. Cement alone cannot hold fabric to wing ribs against the air loads, which is why the ribs are laced at all, and one tight stitch cannot do the work of the stitches left out.
- Q.02
When you lay out rib lacing on a fabric wing, why are the lacing holes punched through the fabric as close to the rib cap as possible?
FAA-H-8083-31B, ch. 3, p. 3-18
- AIt gives the fabric little room to pry away from the rib and tear
- BIt lets the cord sit down inside the rib so it adds no drag
- CIt keeps the cord clear of the finishing tape laid over the rib
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
It gives the fabric little room to pry away from the rib and tear
The lacing cord passes right through the wing from top to bottom and holds both skins to the rib at once. With the holes tight against the rib cap, the fabric has very little to pry against as it tries to pull away from the structure, so it does not tear. The cord does not sink into the rib, and the finishing tape goes on over the lacing afterward.
- Q.03
You have laid polyester fabric over a wing whose structure was precoated with cement that has dried, and it is clamped and positioned all round. What does final adhesion then often involve?
FAA-H-8083-31B, ch. 3, p. 3-17
- ALift the fabric, lay down a wet bed of cement and press the fabric into it
- BLeave it on the dry precoat, since the fill coats will bond it as they cure
- CCement it only along the leading and trailing edges and iron the rest down
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Lift the fabric, lay down a wet bed of cement and press the fabric into it
Typically, 2 coats of adhesive go on the structure first wherever the fabric will touch, and are left to dry. The fabric is laid over relaxed but not wrinkled, clamped round the edges and positioned everywhere before final adhesion, which usually means lifting the fabric, applying a wet bed of cement and pressing the fabric into it, often with another coat over the top. The fabric is cemented at every point of contact, and the fill coats are not what holds it on.
- Q.04
A polyester covering was finished exactly as its STC calls for and has been kept up well. How long should its fill coats go on protecting the fabric from the sun?
FAA-H-8083-31B, ch. 3, p. 3-10
- AAbout 5 years, after which the fabric must be re-covered
- BOnly until the next annual, when they are renewed
- CIndefinitely, as long as they stay in good condition
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Indefinitely, as long as they stay in good condition
UV light is what weakens polyester, and every approved covering system puts fill coats on the fabric to block it. Installed as the STC says, those coatings should be enough to protect the fabric from the sun and should last indefinitely. That is why judging the strength of such a covering is mostly a matter of judging the condition of its coatings, not counting years or annual inspections.
- Q.05
You are about to mix the fabric adhesive for a re-cover in a cold hangar. What should guide how it is mixed?
FAA-H-8083-31B, ch. 3, p. 3-17
- AThe mix that suits a warm shop, since adhesive cures the same anywhere
- BThe temperature the work is being done at, using the maker's or STC's guidance
- CWhatever thins it enough to brush, using any thinner that is on hand
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
The temperature the work is being done at, using the maker's or STC's guidance
The adhesive, and every coating that follows it, should be mixed for its best working properties at the temperature the work is actually being done in, following the manufacturer's or the STC's guidance. A mix meant for a warm shop will not behave the same in the cold, and thinning with whatever is on the shelf brings in material the covering system does not list.
- Q.06
The owner of a vintage airplane first certificated with Grade-A cotton wants it re-covered in cotton to keep it original. What is the practical obstacle?
FAA-H-8083-31B, ch. 3, p. 3-8
- AApproved aircraft cotton fabric is no longer available
- BCotton may no longer be used on any certificated airplane
- CCotton cannot be finished with the dope coatings still sold
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Approved aircraft cotton fabric is no longer available
Grade-A cotton may still be used on any aircraft originally certificated to be covered with it, so the rules are not the problem. Supply is: approved aircraft cotton fabric is no longer available, and the long staple cotton it was made from is no longer produced in this country. That is a big part of why most of these airplanes have been re-covered in polyester under an approved process. Dope-based processes are still in use, refined for polyester.
- Q.07
The strip for a fabric breaking strength test is best cut from an upper surface with a dark colored finish. What makes that spot the right one?
FAA-H-8083-31B, ch. 3, p. 3-9
- ADark coatings come off the strip more easily when it soaks in MEK
- BIt has taken the most UV, so it shows the weakest fabric on the airplane
- CA patch on a dark color will not show once the strip is repaired
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
It has taken the most UV, so it shows the weakest fabric on the airplane
The strip should show the weakest fabric on the airplane, so it comes from where the sun does the most harm: a surface exposed to the elements, usually the top, and best of all one with a dark finish that has absorbed more UV and degraded faster. A strip from a sheltered panel could pass while the rest of the covering is weaker. How easily the coatings strip off, or how the repair looks, has nothing to do with it.
- Q.08
While re-covering a wing, you see an area with no inspection ring that would be hard to reach later without cutting the fabric. What may you do?
FAA-H-8083-31B, ch. 3, p. 3-19
- ANothing, since rings may only go where the old covering had them
- BCut a hole there now and leave it open as a drain
- CInstall an additional ring there for access in the future
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Install an additional ring there for access in the future
Inspection rings go where the manufacturer's data puts them or, lacking that, where they were on the old covering. Beyond that, the technician should install additional rings wherever an area would benefit from access in the future. A ring is not cut open until the access is needed, and a drain is a separate grommet at a low point, not a hole left open where a ring belongs.
- Q.09
Drain holes in a fabric covering are normally reinforced with grommets. When can a drain hole be made without one?
FAA-H-8083-31B, ch. 3, p. 3-6
- AWhen it is in the upper surface, where little water gathers
- BWhen it is made through 2 layers of fabric
- CWhen it is cut with a hot soldering pencil
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
When it is made through 2 layers of fabric
Drain grommets reinforce the openings at the low points through which trapped water escapes. Some drain holes do not need a grommet, though: those made through 2 layers of fabric. Drains belong at low points, not in the upper surface, and a hot soldering pencil is simply a tool that opens the fabric for a grommet's hole and heat seals the cut edge; it does not do away with the grommet.
- Q.10
A steel tube fuselage has had its old fabric stripped off and been cleaned for re-covering. What do many technicians take the chance to do to the bare airframe at this stage?
FAA-H-8083-31B, ch. 3, p. 3-12
- AHeat it to relieve the stress the old fabric's tension left in it
- BWeld a doubler over every tube cluster to strengthen it
- CGrit blast the entire airframe before it is primed
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Grit blast the entire airframe before it is primed
With the covering off, the airframe is cleaned, inspected and repaired, and any corrosion is removed and treated. On a steel tube airframe many technicians take the opportunity to grit blast the whole structure at this stage, and once it is cleaned, inspected and repaired an approved primer goes on. Doublers are added only where a repair calls for them, and the old fabric leaves no stress that needs heating out.
We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.
How a missed code comes back at the oral
Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.II.B. The examiner reads those codes before your oral and practical.
The Airframe oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Airframe also carries 11 practical projects, each with 2 questions attached.
Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.
Questions people ask about aircraft fabric covering
Q.01What is the warp of aircraft fabric?
Warp is the direction along the length of the fabric, parallel to the selvage edge, the woven edge that keeps it from unraveling. Fill is the direction across the width of the fabric, at right angles to the warp.
Q.02Why is aircraft fabric tested for strength?
Because fabric loses strength as it ages, mostly from exposure to sunlight. A punch tester, such as the Maule tester, gives a rough check while the fabric is still on the aircraft. Punch tests are not FAA approved, so when the fabric tests low, a test strip is cut out and pulled to find its breaking strength, and sent to a laboratory if the result is still in doubt.
Q.03What is the difference between the envelope and blanket methods?
An envelope is sewn ahead of time to fit a wing or fuselage and slid over it like a sleeve. The blanket method lays flat pieces of fabric over the structure and glues them to it with the approved cement. Either way the fabric is then shrunk tight with heat.
Q.04Can covering products from different makers be mixed?
No. The fabric, tapes, threads, cements, coatings and the steps for using them together make up the approval for that covering process, usually a supplemental type certificate. Only the approved materials may be used, and substituting another product is not allowed.
Q.05How many aircraft fabric covering questions are on the FAA A&P Airframe test?
The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Non-Metallic Structures subject area 5 to 10% of the Airframe test, which is 5 to 10 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.
Q.06Which FAA handbook chapter covers aircraft fabric covering?
Chapter 3 of FAA-H-8083-31B, the Aviation Maintenance Technician Handbook: Airframe, titled "Aircraft Fabric Covering". It runs from pages 3-1 to 3-24, and the FAA publishes the whole handbook free as a PDF.
Read the documents, not us
Every fact on this page was read from these on 19 August 2026 and 15 November 2026. They are the authority and we are the summary. If we and one of them disagree, they are right.
- FAA-H-8083-31B, Aviation Maintenance Technician Handbook: Airframe, chapter 3www.faa.gov
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standardswww.faa.gov
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards: the written test blueprints (pages 13 and 14) and chapters 6 and 7www.faa.gov
- FAA, Frequently Missed Knowledge Test ACS Codes, 2nd Quarter CY25www.faa.gov
More FAA A&P Airframe subjects
FREE PLAN · NO CARD · 25 QUESTIONS TO START
The bank holds 232 aircraft fabric covering questions.
Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.
Start freeOr answer a few first. The free FAA A&P practice test runs on the page, with no account.