AMA · AF-06 · FAA-H-8083-31B CH. 6
FAA A&P Airframe: Aircraft Wood Structural Repair
For the FAA A&P Airframe test, aircraft wood structural repair is chapter 6 of FAA-H-8083-31B, Aircraft Wood & Structural Repair. Its ACS subject area, Non-Metallic Structures, is 5 to 10% of the test, or 5 to 10 of its 100 scored questions. Our question bank holds 198 questions on it, and the 10 below were written for this page.
Test shares and most-missed codes read from the FAA on 15 November 2026.
What FAA-H-8083-31B chapter 6 covers
Chapter 6 covers wooden aircraft structure: the woods approved for it, with spruce as the standard, plywood and laminated wood, the defects that are and are not acceptable in aircraft wood, and the adhesives used to glue it.
It covers inspecting wood structure for decay, compression failures and glue joint failure, then repairs: scarf joints and splices, spar and rib repairs, and plywood skin repairs, from the splayed patch to the surface, plug and scarf patches.
It runs from pages 6-1 to 6-26 of the Aviation Maintenance Technician Handbook: Airframe, which the FAA publishes free as a PDF.
How much of the FAA A&P Airframe test it is
- 5 to 10%OF THE TESTACS area AM.II.B
- 5 to 10QUESTIONSof 100 scored
- 198IN OUR BANKquestions on this subject
The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Non-Metallic Structures (AM.II.B) is 5 to 10% (5 to 10 questions) on the 100-question Airframe test. The 15 ranges for the Airframe test add up to anywhere from 75% to 160%, so they say how big an area can get, not how many questions you will see from it.
Non-Metallic Structures is not ours alone to cover: our Aircraft Structures, Aircraft Fabric Covering, Advanced Composite Materials and Aircraft Painting and Finishing questions are written to the same area.
No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.
Aircraft wood structural repair questions and answers
10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.
- Q.01
During an inspection of a wooden wing, your moisture meter reads 15 percent in a spar. What does that reading tell you?
FAA-H-8083-31B, ch. 6, p. 6-2
- AWetter than the ideal 8 to 12 percent, so dry it before judging joints
- BWithin the ideal range, so the glue joints can be judged as they stand
- COver the limit for fungus growth, so the spar has to be replaced
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Wetter than the ideal 8 to 12 percent, so dry it before judging joints
Wood has to be dry before its glue joints are judged, because damp wood swells and makes the joints hard to assess. The ideal reading is 8 to 12 percent, so 15 percent is wetter than it should be: dry the airplane in a well-ventilated hangar with the panels open and measure again. It is still under 20 percent, the level above which wood can grow fungus, so this reading alone is no reason to replace anything.
- Q.02
Checking a wooden wing, you find sound wood all around a metal fitting and a metal rib flange on the spar. What does the handbook warn about places like these?
FAA-H-8083-31B, ch. 6, p. 6-5
- ASpar cracks are often hidden under metal fittings and rib flanges
- BWood under metal parts is protected, so it seldom needs checking
- CA crack there always shows as a gap at the edge of the metal part
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Spar cracks are often hidden under metal fittings and rib flanges
Cracks in wood spars are often hidden under metal fittings, metal rib flanges and leading edge skins, so sound wood around a fitting proves nothing about the wood beneath it. The handbook also has fitting bolts removed so their holes can be checked for elongation or crushed fibers. A metal part does not protect the spar from cracking, and a hidden crack need not show at the edge of the part at all.
- Q.03
On a warm afternoon, mixed 2-part adhesive for a wood repair keeps thickening well before the time on its label. What will make the next batch last longer?
FAA-H-8083-31B, ch. 6, p. 6-10
- AStir it every few minutes so it keeps its working strength
- BKeep the mix cooler, within the recommended temperature range
- CWarm it slightly first so it flows onto the wood more easily and evenly
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Keep the mix cooler, within the recommended temperature range
Pot life is a product of time and temperature, so a mix kept cooler, within the range the adhesive maker recommends, stays usable longer, while warming it shortens its life. Stirring does nothing to hold back the cure. Once the stated pot life has run out, the adhesive must not be used, whatever it looks like.
- Q.04
After a hard landing, the wood spar of a wing shows nothing you can see from the outside. Why does it still get particular attention at inspection?
FAA-H-8083-31B, ch. 6, p. 6-6
- AA compression failure there is hard to see and could let the wing fail in flight
- BA heavy shock drives moisture deep into the spar, which then has to be dried out
- CA hard landing loosens every glue joint in the wing, so each has to be remade
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
A compression failure there is hard to see and could let the wing fail in flight
A hard landing can put abnormal bending or compression loads into wooden members, and a compression failure, a rupture across the fibers, can be very hard to see. If one goes undetected in a spar, it may lead to structural failure of the wing in flight, so the spar is looked at closely, for example with a flashlight beam run along the grain. A landing does not push water into the wood, and it does not mean every glue joint has failed.
- Q.05
You are restoring an old wooden airplane whose joints were made with plastic resin glue, and it has spent years in a hot, humid climate. What should you expect of those joints?
FAA-H-8083-31B, ch. 6, p. 6-9
- AThey should be sound, since this glue resists wet weather better than any other
- BThey should be sound as long as the airplane never sat out in freezing weather
- CThey may be failing, since warm, humid conditions break this glue's bond down
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
They may be failing, since warm, humid conditions break this glue's bond down
Plastic resin glue is a urea-formaldehyde adhesive that came on the market in the mid to late 1930s. Tests and service have shown that moist conditions, and above all a warm, humid environment under swell-shrink stress, make its bond deteriorate until it fails, which is why the handbook treats it as obsolete for all aircraft repairs. The best wet-weather resistance belongs to resorcinol glue, and it is heat and humidity, not freezing, that the handbook warns about here.
- Q.06
Why must the 2 bevels of a scarf joint in a wood member be cut so precisely?
FAA-H-8083-31B, ch. 6, p. 6-15
- AMatching bevels let the joint be clamped up without a caul or pressure plate
- BMatching bevels give the even, thin glue line the joint needs
- CMatching bevels let the scarf be cut steeper than 15 to 1
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Matching bevels give the even, thin glue line the joint needs
A scarf has to be cut precisely on both pieces so the glue line is thin and even, and without that the joint may not reach full strength. Getting the same bevel on each piece is the main difficulty in making one. Precise bevels do not change the slope limit, which in a stressed part such as a spar is no steeper than 15 to 1, and they do not remove the need for proper clamping.
- Q.07
You plan to glue a spar splice with resorcinol glue, but the shop is sitting at 60 °F. What should you do?
FAA-H-8083-31B, ch. 6, p. 6-9
- AWarm the shop and the work above 70 °F before gluing and curing
- BGlue it now, and warm just the clamps before you tighten them
- CGlue it now, since resorcinol cures fully at any shop temperature
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Warm the shop and the work above 70 °F before gluing and curing
Resorcinol needs warmth to reach full strength. The joint cannot be counted on if it is assembled and cured below 70 °F, so the shop and the work are brought above that temperature first. Warmer conditions do speed the cure and shorten the open and closed assembly times, so keep an eye on the clock. It is the glue and the wood that need the warmth, so warming just the clamps does not help.
- Q.08
Gluing a long spar splice, you notice your clamps bear down hard at both ends but barely touch the middle. What will the cured joint most likely have?
FAA-H-8083-31B, ch. 6, p. 6-11
- AFull strength all along, since the glue evens itself out as it cures
- BA thick but extra strong glue line in the middle, where the glue pools
- CWeak areas and strong areas in the same joint
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Weak areas and strong areas in the same joint
Even force on the joint is what gives a glued joint its maximum strength. Where the clamps bear down the glue is squeezed into a thin film, and where they barely touch it is not, so non-uniform pressure commonly leaves weak areas and strong areas in the same joint. Glue does not even itself out under uneven clamps, and too little pressure on a poorly fitted joint usually leaves a thick glue line, which is the sign of a weak joint, not a strong one.
- Q.09
A new spruce board bought for a spar repair shows a compression failure, though it has never been in an airplane. How could the failure have got there?
FAA-H-8083-31B, ch. 6, p. 6-9
- AIt was planed with dull knives that crushed the fibers along its surface
- BThe tree was felled on rough ground, or the log or lumber was handled roughly
- CIt was dried too quickly in the kiln, so the grain twisted along its length
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
The tree was felled on rough ground, or the log or lumber was handled roughly
Compression failures come from overstress in compression: natural forces while the tree was growing, felling it on rough or irregular ground, or rough handling of the logs or lumber. So a board can carry one before anyone builds with it. The failure shows as buckled fibers in streaks across the grain, and a board with an obvious one is rejected. Dull knives crush the surface fibers of a glue face, and drying changes a board's shape as it shrinks; neither is a compression failure.
- Q.10
A spruce spar splice is glued with an adhesive whose instructions call for 100 psi of clamping pressure. The glued area is 1.5 inches wide and 9 inches long. What total clamping force does the joint need?
FAA-H-8083-31B, ch. 6, p. 6-11
- A100 pounds
- B7.4 pounds
- C1,350 pounds
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
1,350 pounds
Clamping pressure is force spread over the glued area, so the total force is the pressure times the area. 1.5 times 9 is 13.5 square inches, and 13.5 times 100 psi is 1,350 pounds. 100 pounds would give that pressure on just 1 square inch, and 7.4 comes from dividing the pressure by the area. For softwoods the pressure called for runs from 10 to 150 psi, depending on the glue, and up to 200 psi for hardwoods.
We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.
How a missed code comes back at the oral
Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.II.B. The examiner reads those codes before your oral and practical.
The Airframe oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Airframe also carries 11 practical projects, each with 2 questions attached.
Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.
Questions people ask about aircraft wood structural repair
Q.01Which wood is the standard for aircraft structure?
Spruce. It is the preferred wood and the standard every other species is measured against for strength, and whatever the species, the slope of the grain may be no steeper than 1 in 15.
Q.02What is a compression failure in wood?
A rupture across the wood fibers from being overloaded in compression. It is a serious defect and can be hard to see. Shining a flashlight along the member, parallel to the grain, shows it up as fine ridges or lines across the surface.
Q.03How is a glue joint in wood structure inspected?
With the wood dry, because damp wood swells and closes a failing joint, and under a magnifying glass. Where the glue line seems to part, or no glue can be seen, it is probed with a thin feeler gauge, and if the gauge goes in at all, the joint is defective.
Q.04Why is a scarf joint used to repair a wood spar?
Because a long, shallow taper gives a large glue area and passes the load from one piece to the other gradually. It is the most satisfactory end joint between 2 solid wood members, and in a stressed part such as a spar the slope of the scarf may be no steeper than 15 to 1.
Q.05How many aircraft wood structural repair questions are on the FAA A&P Airframe test?
The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Non-Metallic Structures subject area 5 to 10% of the Airframe test, which is 5 to 10 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.
Q.06Which FAA handbook chapter covers aircraft wood structural repair?
Chapter 6 of FAA-H-8083-31B, the Aviation Maintenance Technician Handbook: Airframe, titled "Aircraft Wood & Structural Repair". It runs from pages 6-1 to 6-26, and the FAA publishes the whole handbook free as a PDF.
Read the documents, not us
Every fact on this page was read from these on 19 August 2026 and 15 November 2026. They are the authority and we are the summary. If we and one of them disagree, they are right.
- FAA-H-8083-31B, Aviation Maintenance Technician Handbook: Airframe, chapter 6www.faa.gov
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standardswww.faa.gov
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards: the written test blueprints (pages 13 and 14) and chapters 6 and 7www.faa.gov
- FAA, Frequently Missed Knowledge Test ACS Codes, 2nd Quarter CY25www.faa.gov
FREE PLAN · NO CARD · 25 QUESTIONS TO START
The bank holds 198 aircraft wood structural repair questions.
Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.
Start freeOr answer a few first. The free FAA A&P practice test runs on the page, with no account.