PrepAMT Academy

AMA · AF-02 · FAA-H-8083-31B CH. 2

FAA A&P Airframe: Aerodynamics, Assembly and Rigging

For the FAA A&P Airframe test, aerodynamics and aircraft rigging is chapter 2 of FAA-H-8083-31B, Aerodynamics, Aircraft Assembly, & Rigging. Its main ACS subject area, Flight Controls, is 5 to 10% of the test, or 5 to 10 of its 100 scored questions. Our question bank holds 402 questions on it, and the 10 below were written for this page.

Test shares and most-missed codes read from the FAA on 15 November 2026.

01 WHAT IT COVERSFAA-H-8083-31B · CH. 2

What FAA-H-8083-31B chapter 2 covers

Chapter 2 starts with aerodynamics: the atmosphere, how an airfoil makes lift, angle of attack, drag, the axes of flight, and stability about each axis. It covers high speed flight and the helicopter, with its rotor systems, controls, dissymmetry of lift, autorotation, and vibration and blade tracking.

The second half is assembly and rigging: control cables and their fittings, turnbuckles and cable tension, pushrods, torque tubes and bellcranks, setting and checking control surface travel, and balancing control surfaces. The chapter closes with a section on inspecting the aircraft, which our Airframe Inspection subject is written from.

It runs from pages 2-1 to 2-67 of the Aviation Maintenance Technician Handbook: Airframe, which the FAA publishes free as a PDF.

02 SHARE OF THE TESTFAA-G-ACS-1 · BLUEPRINT

How much of the FAA A&P Airframe test it is

  • 5 to 10%OF THE TESTACS area AM.II.C
  • 5 to 10QUESTIONSof 100 scored
  • 402IN OUR BANKquestions on this subject

The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Flight Controls (AM.II.C) is 5 to 10% (5 to 10 questions) on the 100-question Airframe test. Our Aerodynamics, Assembly and Rigging questions also reach into Rotorcraft Fundamentals (AM.II.N, 5 to 10%). The 15 ranges for the Airframe test add up to anywhere from 75% to 160%, so they say how big an area can get, not how many questions you will see from it.

Flight Controls is not ours alone to cover: our Aircraft Structures questions are written to the same area.

No code in these areas is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.

03 EXAMPLE QUESTIONSWRITTEN FOR THIS PAGE

Aerodynamics and aircraft rigging questions and answers

10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.

  1. Q.01

    While rigging an elevator trim system with the trim control at neutral, you find the tab sits about 1 degree off streamline with the elevator. What should you check before changing anything?

    FAA-H-8083-31B, ch. 2, p. 2-52

    1. ANothing, since trim tabs are always rigged 1 or 2 degrees off streamline
    2. BWhether the specifications for that airplane call for the tab to be offset
    3. CWhether bending the tab by 1 degree will bring it back to streamline
    SHOW THE ANSWER

    THE ANSWER IS B.

    Whether the specifications for that airplane call for the tab to be offset

    With the trim control at neutral, the tab is usually adjusted to streamline with the control surface. Some airplanes, though, have specifications that call for the tab to be offset 1 or 2 degrees from streamline at neutral, so the manual is checked before the offset is treated as a fault. Only once the tab and its control are both at neutral is the cable tension adjusted. A movable trim tab is set through its linkage, not bent, and most tabs are rigged to streamline.

  2. Q.02

    You are cutting a new length of control cable that will get a swaged terminal at each end. What should the cut length allow for?

    FAA-H-8083-31B, ch. 2, p. 2-40

    1. AThe growth in length that comes with swaging the terminals
    2. BThe cable shortening as the swaged barrels squeeze down on it
    3. CAn extra inch at each end to be soldered so it cannot fray
    SHOW THE ANSWER

    THE ANSWER IS A.

    The growth in length that comes with swaging the terminals

    Swaging squeezes the terminal barrel down onto the cable, and the assembly grows in length as it does, so the cable is cut to length with that growth allowed for. A preservative compound goes on the cable end before it goes into the barrel. Cable ends are never soldered to stop fraying, because solder makes the cable far more likely to pull out of the terminal.

  3. Q.03

    Why do some airplanes have the leading edge of the vertical fin set slightly off the longitudinal center line?

    FAA-H-8083-31B, ch. 2, p. 2-49

    1. ATo give the airplane more directional stability in a sideslip
    2. BTo counter the yaw that engine torque would otherwise cause
    3. CTo make the airplane easier to steer with the rudder on the ground
    SHOW THE ANSWER

    THE ANSWER IS B.

    To counter the yaw that engine torque would otherwise cause

    During an alignment check, a plumb line through the rudder hinge holes should pass centrally through all of them. Some airplanes, though, are built with the leading edge of the vertical fin offset from the longitudinal center line on purpose, to counteract engine torque, so a small offset is not by itself damage. Directional stability comes from fin area, such as a dorsal fin, and ground steering comes from the nose or tail wheel, not from setting the fin at an angle.

  4. Q.04

    Your shop has just swaged a new terminal onto a control cable but has no fixture to proof load it. What should happen before the cable is installed?

    FAA-H-8083-31B, ch. 2, p. 2-41

    1. AInstall it and confirm the swage from the cable tension once rigged
    2. BSend it to a properly equipped facility to have the load test done
    3. CSkip the load test, since the swage has already passed a go/no-go gauge
    SHOW THE ANSWER

    THE ANSWER IS B.

    Send it to a properly equipped facility to have the load test done

    Newly installed swaged terminals and locally made splices are proof loaded before installation, by slowly applying 60 percent of the cable's rated breaking strength and holding it for at least 3 minutes, with guards over the cable. If the shop has no proper test fixture, the test is contracted out to a facility that has one. A go/no-go gauge only checks the terminal's shank diameter, and rigging tension is far below a proof load, so neither one takes the place of the test.

  5. Q.05

    You are rigging a trim tab that is driven by a jackscrew. With the tab run out to each of its extreme positions, what must you check on the jackscrew?

    FAA-H-8083-31B, ch. 2, p. 2-52

    1. AThat it turns freely by hand with the cable tension slacked off
    2. BThat its threads are dry, since grease would collect grit
    3. CThat it is not extended beyond its specified limits
    SHOW THE ANSWER

    THE ANSWER IS C.

    That it is not extended beyond its specified limits

    When a trim tab is worked by a jackscrew, the screw is checked with the tab at each of its extreme positions, where it is run out the farthest, to see that it is not extended beyond the specified limits. Whether it turns freely with the cables slack, or what is on its threads, says nothing about how far it is run out, and that extension is what this rigging check is for.

  6. Q.06

    You have finished assembling and rigging a biplane, and every wire tension and angle checks within limits. What is a sensible next step before the paperwork?

    FAA-H-8083-31B, ch. 2, p. 2-57

    1. ARetension every wire to the top of its range to leave a margin
    2. BBack each turnbuckle off a little so the wires can settle in
    3. CStep back from the airplane and look it over as a whole
    SHOW THE ANSWER

    THE ANSWER IS C.

    Step back from the airplane and look it over as a whole

    Once the rigging is believed correct, the handbook's advice is to move away from the airplane and take a good look at the finished product. Are the wings symmetrical, does the dihedral look even, is the tail square with the fuselage, and are the wing hardware, flying wires and control cables safetied? Retensioning to the top of the range or backing the turnbuckles off would only undo tensions already set within limits.

  7. Q.07

    You are checking aileron travel from the flight deck with the control wheel turned hard against its stops. What else must you confirm in that position?

    FAA-H-8083-31B, ch. 2, p. 2-52

    1. AThat the chains and cables have not reached the end of their own travel
    2. BThat the cable tension has risen to the highest figure on the chart
    3. CThat the aileron trim tab has run out to its full deflection as well
    SHOW THE ANSWER

    THE ANSWER IS A.

    That the chains and cables have not reached the end of their own travel

    Travel is checked with the controls worked from the flight deck, not by pushing the surface, and with the controls against their stops the chains and cables must still have travel left. If one of them ran out first, it would be doing the job of the stop. Cable tension is set and checked on its own, and the trim tab has a travel check of its own too.

  8. Q.08

    An elevator is set up on a stand to have its balance checked after a repair. Before you go on with the balancing, what do you find with a bubble protractor?

    FAA-H-8083-31B, ch. 2, p. 2-37

    1. AThe neutral position of the surface
    2. BThe full travel of its trim tab each way
    3. CThe deflection the cable tension puts on it
    SHOW THE ANSWER

    THE ANSWER IS A.

    The neutral position of the surface

    A control surface being rebalanced is taken off the airplane and supported on a stand from its own hinge points. A bubble protractor is then used to find its neutral position before the balancing goes on. The trim tab is secured in neutral on the stand rather than run through its travel, and with the surface off the airplane no cable tension acts on it.

  9. Q.09

    A main rotor blade is going into storage in a container that was last used to ship a different item. What should be done about the old markings on the container?

    FAA-H-8083-31B, ch. 2, p. 2-33

    1. ALeave them, since the blade's own records travel inside the box
    2. BAdd the blade's details beside them so both items are listed
    3. CObliterate them and mark the blade's model, part and serial numbers
    SHOW THE ANSWER

    THE ANSWER IS C.

    Obliterate them and mark the blade's model, part and serial numbers

    When a rotor blade is packed for storage, the old markings that applied to the container's earlier shipment or the item it held are obliterated, and the blade model, part number and serial number are marked on the outside. Leaving the old markings, or adding to them, invites a mix-up. The blade's records do go in the container, in a waterproof bag in the record tube, but they do not replace the outside markings.

  10. Q.10

    Every helicopter has to show it can autorotate before it can be certificated. Why does that ability matter so much?

    FAA-H-8083-31B, ch. 2, p. 2-27

    1. AIt is the way the helicopter can be landed safely if the engine fails
    2. BIt is the way the rotor is brought up to speed before each flight
    3. CIt proves the tail rotor gearbox can carry full engine power
    SHOW THE ANSWER

    THE ANSWER IS A.

    It is the way the helicopter can be landed safely if the engine fails

    Autorotation is the means by which a helicopter can be landed safely if its engine fails: the freewheeling unit lets the main rotor keep turning with the engine disengaged. That is why every helicopter must demonstrate the ability in order to be certificated. The engine, not autorotation, brings the rotor up to speed, and autorotating says nothing about the tail rotor gearbox carrying full power.

We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.

04 AND THEN THE ORAL§ 65.79

How a missed code comes back at the oral

Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.II.C or AM.II.N. The examiner reads those codes before your oral and practical.

The Airframe oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Airframe also carries 11 practical projects, each with 2 questions attached.

Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.

05 COMMON QUESTIONSFAQ

Questions people ask about aerodynamics and aircraft rigging

Q.01

What is the difference between angle of attack and angle of incidence?

Angle of attack is the angle between the wing’s chord line and the relative wind, and it changes all through a flight. Angle of incidence is the angle between the chord line and the longitudinal axis of the aircraft. It is set when the aircraft is built and rigged.

Q.02

How is control cable tension checked?

With a tensiometer, which measures the force needed to push the cable into an offset between 2 hardened blocks, using the riser that suits the cable size. The dial reading is turned into pounds with the chart for that tensiometer, then compared with the cable rigging chart, which gives the tension for that cable size at the air temperature of the day.

Q.03

What is dissymmetry of lift?

In forward flight the advancing blade meets a relative wind increased by the helicopter’s forward speed, and the retreating blade one reduced by it, so the 2 halves of the disc would make unequal lift. Blade flapping evens it out: the advancing blade flaps up and its angle of attack falls, and the retreating blade flaps down and its angle of attack rises.

Q.04

What is checked on a turnbuckle after rigging?

That the cable tension is right, that no more than 3 threads of either terminal are showing outside the turnbuckle barrel, and that the turnbuckle is safetied, with safety wire or a clip-type locking device, so it cannot turn.

Q.05

How many aerodynamics and aircraft rigging questions are on the FAA A&P Airframe test?

The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Flight Controls subject area 5 to 10% of the Airframe test, which is 5 to 10 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it. Our Aerodynamics, Assembly and Rigging questions also reach into Rotorcraft Fundamentals (5 to 10%).

Q.06

Which FAA handbook chapter covers aerodynamics and aircraft rigging?

Chapter 2 of FAA-H-8083-31B, the Aviation Maintenance Technician Handbook: Airframe, titled "Aerodynamics, Aircraft Assembly, & Rigging". It runs from pages 2-1 to 2-67, and the FAA publishes the whole handbook free as a PDF.

FREE PLAN · NO CARD · 25 QUESTIONS TO START

The bank holds 402 aerodynamics and aircraft rigging questions.

Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.

Start free

Or answer a few first. The free FAA A&P practice test runs on the page, with no account.