PrepAMT Academy

AMP · PP-07 · FAA-H-8083-32B CH. 7

FAA A&P Powerplant: Propellers

For the FAA A&P Powerplant test, aircraft propellers is chapter 7 of FAA-H-8083-32B, Propellers. Its ACS subject area, Propellers, is 5 to 10% of the test, or 5 to 10 of its 100 scored questions. Our question bank holds 312 questions on it, and the 10 below were written for this page.

Test shares and most-missed codes read from the FAA on 15 November 2026.

01 WHAT IT COVERSFAA-H-8083-32B · CH. 7

What FAA-H-8083-32B chapter 7 covers

Chapter 7 covers how a propeller works, blade angle, pitch and the forces on a turning blade, and the types: fixed pitch, ground adjustable, controllable pitch, constant speed, feathering and reversing propellers, with the governors that control them and turboprop propeller systems.

It also covers propeller ice control, synchronizing, inspecting wood, metal and composite propellers, tracking and balancing, servicing, overhaul, and troubleshooting.

It runs from pages 7-1 to 7-41 of the Aviation Maintenance Technician Handbook: Powerplant, which the FAA publishes free as a PDF.

02 SHARE OF THE TESTFAA-G-ACS-1 · BLUEPRINT

How much of the FAA A&P Powerplant test it is

  • 5 to 10%OF THE TESTACS area AM.III.M
  • 5 to 10QUESTIONSof 100 scored
  • 312IN OUR BANKquestions on this subject

The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Propellers (AM.III.M) is 5 to 10% (5 to 10 questions) on the 100-question Powerplant test. The 13 ranges for the Powerplant test add up to anywhere from 65% to 140%, so they say how big an area can get, not how many questions you will see from it.

No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.

03 EXAMPLE QUESTIONSWRITTEN FOR THIS PAGE

Aircraft propellers questions and answers

10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.

  1. Q.01

    A propeller passes its static balance check on the knife edges, yet in service one blade is found to pull harder than the other and the airplane shakes. Which check goes after this kind of unbalance?

    FAA-H-8083-32B, ch. 7, p. 7-24

    1. AAdding permanent fixed weights to the hub at the light blade
    2. BChecking each blade's contour and blade angle setting
    3. CRepacking the blade bearings with fresh grease
    SHOW THE ANSWER

    THE ANSWER IS B.

    Checking each blade's contour and blade angle setting

    When the thrust, or pull, of the blades is unequal, the propeller has aerodynamic unbalance, and that can be there even when its mass is in balance. It is largely cleared by checking the contour of each blade and its blade angle setting, so every blade does the same work. Fixed weights correct static unbalance, which this propeller has already passed, and fresh grease changes neither the shape of a blade nor its angle.

  2. Q.02

    As long as the blades track within tolerance, why is dynamic unbalance from uneven mass distribution so small on most propellers that it can be ignored?

    FAA-H-8083-32B, ch. 7, p. 7-24

    1. AIt is short along the crankshaft for its diameter, its blades in one plane
    2. BCentrifugal force evens out the mass of every blade once it turns fast
    3. CThe governor trims each blade's angle to cancel out any unbalance
    SHOW THE ANSWER

    THE ANSWER IS A.

    It is short along the crankshaft for its diameter, its blades in one plane

    Dynamic unbalance comes when the CG of similar parts, such as the blades, does not follow the same plane of rotation. A propeller is short along the crankshaft compared with its diameter, and its blades are fixed to the hub in one plane square to the running axis, so this unbalance is negligible as long as the track tolerance is met. Centrifugal force does not change a blade's mass, and a governor moves all the blades together, not one at a time.

  3. Q.03

    You are fitting a newly overhauled flange-mounted propeller, and its dowel studs let it go on in 2 positions, 180 degrees apart. How do you choose between them?

    FAA-H-8083-32B, ch. 7, p. 7-27

    1. ATake either one without checking, since the dowels make them identical
    2. BTake whichever one makes the mounting nuts easier to reach
    3. CCheck whether the engine or airframe manual specifies one
    SHOW THE ANSWER

    THE ANSWER IS C.

    Check whether the engine or airframe manual specifies one

    A flange propeller can be installed in a given position or 180 degrees from it, so the engine and airframe manuals are checked to see whether either specifies the mounting position. The 2 dowel studs only transfer torque and index the hub to the crankshaft; they do not decide which position is right, and how easy the nuts are to reach is no guide at all. A propeller that was dynamically balanced on that engine goes back in its marked position.

  4. Q.04

    You are spin-balancing a propeller, but run after run the readings will not settle, and you find a worn, loose part in the engine mounting. What is the right move?

    FAA-H-8083-32B, ch. 7, p. 7-25

    1. ARepair the worn and loose parts first, then balance the propeller
    2. BKeep adding balance weights until the reading comes down
    3. CRun the balance at a higher rpm, where the loose part stops moving
    SHOW THE ANSWER

    THE ANSWER IS A.

    Repair the worn and loose parts first, then balance the propeller

    Dynamic balancing only corrects the mass imbalance of the parts that turn outside the engine. If the engine or aircraft is in poor mechanical condition, balancing will not bring the vibration down, and defective, worn or loose parts make it impossible, so they are fixed first. Piling on weights cannot cure it, and a change of run-up speed does not tighten a loose part either.

  5. Q.05

    You are about to hand prop an engine, and from where you are standing the only way to reach the blade is to lean in toward the propeller. Why should you move your feet instead?

    FAA-H-8083-30B, ch. 1, p. 1-13

    1. ALeaning in keeps your hands too far back to push the blade down
    2. BLeaning in puts your head into the exhaust stream when the engine fires
    3. CLeaning throws you off balance, and you could fall into the blades
    SHOW THE ANSWER

    THE ANSWER IS C.

    Leaning throws you off balance, and you could fall into the blades

    When hand propping, stand on firm ground, close enough to the propeller that you can reach the blade and still step away as it is pulled down. A stance that makes you lean toward the propeller throws your body off balance, and if the engine starts you could fall into the blades. Push the blade down with the palms of your hands, never with your fingers curled over the edge, since kickback can break them or pull you into the blade path.

  6. Q.06

    During a run-up you can see the spinner wobbling, and the propeller seems to be out of balance. What usually causes a spinner to wobble like that?

    FAA-H-8083-32B, ch. 7, p. 7-22

    1. AOne blade set a little high on its low-pitch angle
    2. BA badly shimmed front support, or a cracked or bent spinner
    3. CGrease that has leaked from the blade bearings into the dome
    SHOW THE ANSWER

    THE ANSWER IS B.

    A badly shimmed front support, or a cracked or bent spinner

    The spinner can add to an out-of-balance condition, and a wobble you can see while the engine runs is the sign. It is usually caused by too little shimming at the spinner front support, or by a spinner that is cracked or deformed. A blade angle error changes the pull of that one blade, not how true the spinner runs, and leaked grease shifts the balance without bending anything.

  7. Q.07

    After a season of flying through rain, the leading edges of an aluminum propeller show many small pits. Why should they be dealt with soon rather than left?

    FAA-H-8083-30B, ch. 8, p. 8-26

    1. ACorrosion makes them grow quickly, until the edge may have to be filed smooth
    2. BThey throw the blade out of track, since the pits change its tip path
    3. CThey are only marks in the finish, and on bare metal they never grow any deeper
    SHOW THE ANSWER

    THE ANSWER IS A.

    Corrosion makes them grow quickly, until the edge may have to be filed smooth

    Rain, spray and other airborne grit hit a turning blade hard enough to leave small pits along its leading edge. Unless something is done to prevent it, corrosion makes those pits grow quickly, and they can get so large that the leading edge has to be filed until it is smooth again. Leaving them only gives the corrosion more time, and pits have nothing to do with where the tip runs.

  8. Q.08

    Grit, spray and rain wear at propeller blades in service. Comparing steel blades with aluminum alloy blades, which stand up better to that abrasion and to corrosion?

    FAA-H-8083-30B, ch. 8, p. 8-26

    1. AAluminum alloy, because its oxide skin seals the surface
    2. BThey hold up about the same, being metal blades
    3. CSteel, which resists both of them better
    SHOW THE ANSWER

    THE ANSWER IS C.

    Steel, which resists both of them better

    Steel propeller blades have more resistance to abrasion and corrosion than aluminum alloy blades, so the 2 metals do not hold up the same, and an oxide skin does not close that gap. Rubbed down with oil after each flight, a steel blade keeps a smooth surface for a long time. The oil film helps at inspection too, since oil that seeps into a crack oxidizes and makes it easier to see.

  9. Q.09

    Reading a universal propeller protractor, you count 23 whole degrees between the 2 zeros, and the vernier line nearest to perfect alignment with a degree line is 7 vernier spaces from the vernier zero. What is the blade angle?

    FAA-H-8083-32B, ch. 7, p. 7-24

    1. A23.3 degrees
    2. B23.7 degrees
    3. C30 degrees
    SHOW THE ANSWER

    THE ANSWER IS B.

    23.7 degrees

    10 spaces on the vernier scale take up the same length as 9 on the degree scale, so each vernier space stands for a tenth of a degree. The whole degrees between the 2 zeros give 23, and the 7 vernier spaces out to the line in best alignment give 7 tenths, so the blade angle is 23.7 degrees. Reading the 7 spaces as whole degrees gives 30, and counting them back from the wrong end of the vernier gives 23.3.

  10. Q.10

    A propeller's 75 percent blade station is 30 inches from the hub center, and the tangent of the blade angle there is 0.3. Taking pi as 3.14, what is its geometric pitch?

    FAA-H-8083-32B, ch. 7, p. 7-2

    1. A28.3 inches
    2. B18 inches
    3. C56.5 inches
    SHOW THE ANSWER

    THE ANSWER IS C.

    56.5 inches

    Geometric pitch is 2 times pi times the radius at the 75 percent station times the tangent of the blade angle there. 2 times 3.14 times 30 is 188.4, and 188.4 times 0.3 is 56.52, so about 56.5 inches. Leaving out the 2 gives about 28.3 inches, and leaving out pi gives 18.

We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.

04 AND THEN THE ORAL§ 65.79

How a missed code comes back at the oral

Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.III.M. The examiner reads those codes before your oral and practical.

The Powerplant oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Powerplant also carries 11 practical projects, each with 2 questions attached.

Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.

05 COMMON QUESTIONSFAQ

Questions people ask about aircraft propellers

Q.01

What does a propeller governor do?

It holds the rpm the pilot selects by changing the blade angle. The flight deck control sets the tension on the governor’s speeder spring, flyweights sense the speed, and the governor sends oil to the propeller’s hydraulic cylinder or lets it out, changing the blade angle until the rpm is back where it was set.

Q.02

What does feathering a propeller do?

It turns the blades of a constant speed propeller to about 90 degrees, edge on to the airflow, when an engine fails on a multi-engine aircraft. That cuts the propeller’s drag to a minimum and stops it windmilling.

Q.03

What is propeller blade track?

The position of each blade tip relative to the others, which should turn in the same plane of rotation. It shows only their relative positions, not the path they fly. The difference in track at like points must not exceed the propeller maker’s tolerance.

Q.04

What is the difference between blade angle and angle of attack?

Blade angle is the angle between the face or chord of a blade section and the plane in which the propeller turns. Angle of attack is the angle between the chord and the relative wind, which changes with the aircraft’s speed and the propeller’s rpm.

Q.05

How many aircraft propellers questions are on the FAA A&P Powerplant test?

The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Propellers subject area 5 to 10% of the Powerplant test, which is 5 to 10 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.

Q.06

Which FAA handbook chapter covers aircraft propellers?

Chapter 7 of FAA-H-8083-32B, the Aviation Maintenance Technician Handbook: Powerplant, titled "Propellers". It runs from pages 7-1 to 7-41, and the FAA publishes the whole handbook free as a PDF.

FREE PLAN · NO CARD · 25 QUESTIONS TO START

The bank holds 312 aircraft propellers questions.

Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.

Start free

Or answer a few first. The free FAA A&P practice test runs on the page, with no account.