AMP · PP-08 · FAA-H-8083-32B CH. 8
FAA A&P Powerplant: Engine Removal and Replacement
For the FAA A&P Powerplant test, aircraft engine removal and replacement is chapter 8 of FAA-H-8083-32B, Engine Removal & Replacement. Its main ACS subject area, Reciprocating Engines, is 5 to 15% of the test, or 5 to 15 of its 100 scored questions. Our question bank holds 202 questions on it, and the 10 below were written for this page.
Test shares and most-missed codes read from the FAA on 15 November 2026.
What FAA-H-8083-32B chapter 8 covers
Chapter 8 covers why engines come off, from reaching the end of their operating time to sudden stoppage, metal in the oil and falling performance, and how to prepare and remove one: draining it, disconnecting the lines, controls and wiring, hoisting it and setting it on a stand.
It covers preparing and installing the replacement engine, the quick engine change assembly, engine mounts and vibration isolation, rigging and checking the controls, the first run, and preserving and storing engines that are out of service.
It runs from pages 8-1 to 8-22 of the Aviation Maintenance Technician Handbook: Powerplant, which the FAA publishes free as a PDF.
How much of the FAA A&P Powerplant test it is
- 5 to 15%OF THE TESTACS area AM.III.A
- 5 to 15QUESTIONSof 100 scored
- 202IN OUR BANKquestions on this subject
The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Reciprocating Engines (AM.III.A) is 5 to 15% (5 to 15 questions) on the 100-question Powerplant test. Our Engine Removal and Replacement questions also reach into Turbine Engines (AM.III.B, 5 to 10%) and Engine Inspection (AM.III.C, 5 to 10%). The 13 ranges for the Powerplant test add up to anywhere from 65% to 140%, so they say how big an area can get, not how many questions you will see from it.
Reciprocating Engines is not ours alone to cover: our Reciprocating and Turbine Engines and Light-Sport Aircraft Engines questions are written to the same area.
No code in these areas is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.
Aircraft engine removal and replacement questions and answers
10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.
- Q.01
Most firewall electrical disconnects use AN or MS connectors, each a plug and a receptacle. What keeps a plug from coming apart while the airplane is operating?
FAA-H-8083-32B, ch. 8, p. 8-7
- AA spring clip that snaps over the back of the plug body
- BA knurled sleeve nut on the threaded outlet, wired if needed
- CA bead of sealant laid around the joint once it is mated
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
A knurled sleeve nut on the threaded outlet, wired if needed
Each AN or MS connector is a plug assembly and a receptacle assembly. To prevent accidental disconnection in operation, the outlet is threaded so a knurled sleeve nut screws onto it, and the nut is safety wired if necessary, with steel wire holding it full tight. A spring clip is not how these connectors are held, and sealant would only make the next disconnection harder without locking anything.
- Q.02
Before trimming a turbofan with a hydromechanical fuel control, where is the engine trim gauge connected?
FAA-H-8083-32B, ch. 8, p. 8-14
- AAt a T-fitting in the turbine discharge pressure line
- BAt the INC. MAX screw on the fuel control body
- CIn place of the compressor inlet temperature sensor's lead
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
At a T-fitting in the turbine discharge pressure line
For a trim run, the aircraft is headed into the wind, the exhaust area is checked clear, and the engine trim gauge is fitted to a T-fitting in the turbine discharge pressure line. The engine is then started and allowed to stabilize for 5 minutes before the fuel control is touched, and the readings are corrected for temperature and pressure. If the control is out of limits, the INC. MAX screw is turned about 1/8 turn at a time until the value is right.
- Q.03
Checking a stored engine, you find the silica gel in one dehydrator plug has gone from blue right through lavender and pink to a natural, near white color. About what relative humidity does that show around that cylinder?
FAA-H-8083-32B, ch. 8, p. 8-19
- AAbout 15 percent, still inside the blue range
- BAbout 30 percent, the point where lavender first shows
- CAbout 60 percent, high enough for corrosion to start
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
About 60 percent, high enough for corrosion to start
Cobalt chloride treated silica gel stays bright blue while the air is dry. As the relative humidity rises, the blue gets paler, turns lavender at 30 percent, and fades through shades of pink until it is natural or white at 60 percent. Corrosion does not normally take place below 30 percent relative humidity, so a white plug means the air in that cylinder is damp enough for it, and the cylinder needs attention.
- Q.04
Checking the engine controls on an older airplane before an engine change, you find a pulley and the cable on it both worn flat where they meet. What does that tell you?
FAA-H-8083-32B, ch. 8, p. 8-5
- AThe pulley has not been turning, so the cable slides over it
- BThe cable has stretched, and taking up its tension will cure it
- CThis is normal bedding-in wear that shows the cable is rolling
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
The pulley has not been turning, so the cable slides over it
A pulley that is not turning freely is easy to spot, because both it and the cable wear where the cable slides over the pulley instead of rolling with it. Check its bearing for excessive play or wobble with the cable tension off, and look the cable over for corrosion and broken strands. A cable that rolls as it should does not wear itself and the pulley flat, and more tension only makes the sliding worse.
- Q.05
Before a replacement engine goes in, you find a dented section of air duct, and the fabric anti-chafing strip at its joint is worn so it no longer seals. What should be done?
FAA-H-8083-32B, ch. 8, p. 8-6
- AReplace the whole duct section, since any dent rules it out
- BLeave both alone, since the joint only has to sit close
- CPound out the dent and replace the anti-chafing strip
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Pound out the dent and replace the anti-chafing strip
Air ducts are checked for dents and for the fabric or rubber anti-chafing strips where sections join. Dents may be pounded out, so the section does not have to be scrapped, but a strip that has pulled loose or worn until it no longer makes a tight seal is replaced. A joint that leaks lets the air go somewhere other than where it is meant to, so leaving the strip is not an option either.
- Q.06
You are about to reuse a hose clamp on a low-pressure engine line. As you run the screw in, one part of the band feels soft and starts to stretch. What do you do?
FAA-H-8083-32B, ch. 8, p. 8-10
- AKeep tightening to the usual torque, since a band stretches as it seats
- BReject the clamp, since a soft area is a material defect
- CFit a second clamp beside it and keep both on the hose
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Reject the clamp, since a soft area is a material defect
Before a hose clamp is used, the security of its welding or riveting and the smooth working of its adjusting screw are checked. A clamp that is badly distorted or has a material defect is rejected, and extremely brittle or soft areas that can break or stretch under tightening are exactly such defects. A second clamp does not make a defective one safe, and a band that stretches as it is tightened will not keep its grip on the hose.
- Q.07
You are closing a wooden shipping case over an engine sealed in its protective envelope. As you lower the case cover into position, what must you be careful about?
FAA-H-8083-32B, ch. 8, p. 8-21
- AThat the cover does not twist and tear the protective envelope
- BThat the cover presses the silica gel bags flat against the engine
- CThat the cover seals airtight against the envelope's heat-fused edge
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
That the cover does not twist and tear the protective envelope
The engine's protection comes from the envelope around it: silica gel is put inside, as much air as possible is drawn out, and the edges are fused shut with heat. Lowering the wooden cover carelessly can twist the envelope and tear it, which lets moist air back in. Before the cover goes on, a quick inventory is made and the humidity indicator card is placed where it can be seen through the inspection window. The cover itself is not meant to seal anything.
- Q.08
You are removing only the basic engine, leaving the mount on the aircraft. Where are the electrical leads to the starter and generators disconnected?
FAA-H-8083-32B, ch. 8, p. 8-6
- AAt the firewall connectors, with the rest of the engine wiring
- BAt the starter and generators themselves
- CAt the main bus, after pulling their circuit breakers
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
At the starter and generators themselves
Most electrical disconnections for an engine change are made at the firewall, often at AN or MS connectors. When only the basic engine is coming out, though, the starter and generator leads come off at those units themselves. The magnetos are disconnected first and grounded right away, and the exposed connector ends are taped against dirt and moisture.
- Q.09
An engine has flown 60 hours in the last 2 weeks and will now sit unused for a few weeks at an airport with dry, mild weather. What does its recent flying mean for corrosion inside the cylinders?
FAA-H-8083-32B, ch. 8, p. 8-18
- AIt must be fully preserved before it is left standing for even one night
- BIt can stand for a year or more untouched with no preservation at all
- CIt should stand idle for several weeks without corrosion damage
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
It should stand idle for several weeks without corrosion damage
An engine that has built up 50 hours or more in a short period has a varnish on its cylinder walls that tends to protect them from corrosion. In favorable conditions such an engine can stand inactive for several weeks with no sign of corrosion damage. That is the best case: an aircraft kept near oceans, lakes or rivers, or in a humid region, needs preservation far more than one kept somewhere dry, and longer storage still calls for preserving the engine.
- Q.10
During an engine removal, a metal line is joined to its other half by a short length of rubber hose held with 2 clamps. How is that joint normally disconnected?
FAA-H-8083-32B, ch. 8, p. 8-8
- ALoosen both clamps and slide the hose onto the tube staying on the aircraft
- BPull the hose straight off the engine side with pliers, twisting until it frees
- CHeat the hose with a torch until it softens enough to pull off the tube
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Loosen both clamps and slide the hose onto the tube staying on the aircraft
Where 2 lengths of metal tubing are joined by a piece of rubber hose, the joint is broken by loosening the hose clamps and sliding the hose back onto the tube that stays with the aircraft, which leaves the engine side free. A container catches whatever drains out, and the open lines are then plugged or covered with moisture-proof tape straight away. Heat or pliers would only damage the hose and risk a fire.
We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.
How a missed code comes back at the oral
Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.III.A or AM.III.B or AM.III.C. The examiner reads those codes before your oral and practical.
The Powerplant oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Powerplant also carries 11 practical projects, each with 2 questions attached.
Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.
Questions people ask about aircraft engine removal and replacement
Q.01What is engine sudden stoppage?
A very rapid and complete stop, where the rpm goes to zero in less than one complete revolution of the propeller, from a propeller strike or engine seizure, a collapsed landing gear or a nose over. It can crack propeller gear teeth, damage the gear train and misalign the crankshaft, so the engine usually has to be replaced, or taken apart and inspected to the manufacturer’s instructions.
Q.02What is a quick engine change assembly?
A QECA, also called an engine power package: the engine with the accessories it needs already installed, ready to be hung on the aircraft as one unit, which shortens the time an engine change takes.
Q.03Why can metal in the oil mean an engine has to come off?
Heavy metal particles in the oil mean a definite engine failure, and the engine must come off. If the particles are only like fine filings, the inspection goes on to decide whether the engine is serviceable, and the oil system is checked again after the engine has run.
Q.04How is an engine kept from corroding in storage?
It is coated with corrosion preventive compound and sealed in a protective envelope or container with bags of silica gel desiccant, which keep the air around it dry. Humidity indicator envelopes, filled with cobalt chloride treated silica gel, can be seen through a small window and show when the desiccant needs changing.
Q.05How many aircraft engine removal and replacement questions are on the FAA A&P Powerplant test?
The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Reciprocating Engines subject area 5 to 15% of the Powerplant test, which is 5 to 15 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it. Our Engine Removal and Replacement questions also reach into Turbine Engines (5 to 10%) and Engine Inspection (5 to 10%).
Q.06Which FAA handbook chapter covers aircraft engine removal and replacement?
Chapter 8 of FAA-H-8083-32B, the Aviation Maintenance Technician Handbook: Powerplant, titled "Engine Removal & Replacement". It runs from pages 8-1 to 8-22, and the FAA publishes the whole handbook free as a PDF.
Read the documents, not us
Every fact on this page was read from these on 19 August 2026 and 15 November 2026. They are the authority and we are the summary. If we and one of them disagree, they are right.
- FAA-H-8083-32B, Aviation Maintenance Technician Handbook: Powerplant, chapter 8www.faa.gov
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standardswww.faa.gov
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards: the written test blueprints (pages 13 and 14) and chapters 6 and 7www.faa.gov
- FAA, Frequently Missed Knowledge Test ACS Codes, 2nd Quarter CY25www.faa.gov
FREE PLAN · NO CARD · 25 QUESTIONS TO START
The bank holds 202 aircraft engine removal and replacement questions.
Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.
Start freeOr answer a few first. The free FAA A&P practice test runs on the page, with no account.