PrepAMT Academy

AMP · PP-11 · FAA-H-8083-32B CH. 11

FAA A&P Powerplant: Light-Sport Aircraft Engines

For the FAA A&P Powerplant test, light-sport aircraft engines is chapter 11 of FAA-H-8083-32B, Light-Sport Aircraft Engines. Its ACS subject area, Reciprocating Engines, is 5 to 15% of the test, or 5 to 15 of its 100 scored questions. Our question bank holds 233 questions on it, and the 10 below were written for this page.

Test shares and most-missed codes read from the FAA on 15 November 2026.

01 WHAT IT COVERSFAA-H-8083-32B · CH. 11

What FAA-H-8083-32B chapter 11 covers

Chapter 11 covers the small engines that power light-sport and similar aircraft: 2-stroke Rotax engines such as the 447, 503 and 582, Rotax 4-stroke engines such as the 912, with their liquid and air cooled heads, the HKS, Jabiru engines, and direct drive engines based on the VW.

Across these engines it covers the fuel, lubrication, cooling, ignition and exhaust systems, daily and general maintenance, inspection, troubleshooting and preservation.

It runs from pages 11-1 to 11-25 of the Aviation Maintenance Technician Handbook: Powerplant, which the FAA publishes free as a PDF.

02 SHARE OF THE TESTFAA-G-ACS-1 · BLUEPRINT

How much of the FAA A&P Powerplant test it is

  • 5 to 15%OF THE TESTACS area AM.III.A
  • 5 to 15QUESTIONSof 100 scored
  • 233IN OUR BANKquestions on this subject

The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Reciprocating Engines (AM.III.A) is 5 to 15% (5 to 15 questions) on the 100-question Powerplant test. The 13 ranges for the Powerplant test add up to anywhere from 65% to 140%, so they say how big an area can get, not how many questions you will see from it.

Reciprocating Engines is not ours alone to cover: our Reciprocating and Turbine Engines and Engine Removal and Replacement questions are written to the same area.

No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.

03 EXAMPLE QUESTIONSWRITTEN FOR THIS PAGE

Light-sport aircraft engines questions and answers

10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.

  1. Q.01

    Jabiru pistons run straight in the steel bores of their chrome molybdenum cylinders. What are the top piston rings made of to suit those bores?

    FAA-H-8083-32B, ch. 11, p. 11-10

    1. ACast iron, to work against the steel bores
    2. BAluminum alloy, to match the pistons themselves
    3. CBronze, so they wear in quickly against the steel
    SHOW THE ANSWER

    THE ANSWER IS A.

    Cast iron, to work against the steel bores

    Jabiru machines its cylinders from 4140 chrome molybdenum steel bar, and the pistons run directly in the steel bores. Each piston carries 3 rings, and the top rings are cast iron to complement those chrome molybdenum bores. Aluminum and bronze are too soft to make a ring that seals and wears well against a hard steel bore.

  2. Q.02

    On a Jabiru, the high-tension current from the 2 fixed ignition coils goes to the center posts of 2 automotive-type distributors. What are those distributors, in effect?

    FAA-H-8083-32B, ch. 11, p. 11-10

    1. ABreaker point units that also set the spark timing
    2. BSimply rotors and caps that pass current to the plugs
    3. CSmall magnetos that make a spark of their own
    SHOW THE ANSWER

    THE ANSWER IS B.

    Simply rotors and caps that pass current to the plugs

    Magnets on the Jabiru flywheel pass 2 fixed coils, and the high-tension current they make goes by leads to 2 automotive-type distributors. Those distributors are simply rotors and caps, which pass the current on to the automotive spark plugs, 2 in the top of each cylinder head. The system is transistorized and its timing is fixed, so there are no breaker points to set, and the high voltage comes from the coils, not from the distributors.

  3. Q.03

    Jabiru machines its cylinder heads from solid aluminum. What kind of valve seats do those heads use?

    FAA-H-8083-32B, ch. 11, p. 11-10

    1. ANo inserts; the valves seat on the head's aluminum
    2. BBronze seats screwed into threaded bores in the head
    3. CReplaceable nickel steel seats shrunk into the head
    SHOW THE ANSWER

    THE ANSWER IS C.

    Replaceable nickel steel seats shrunk into the head

    Jabiru heads are machined from solid aluminum billet, and their replaceable valve seats are nickel steel, shrunk into the aluminum heads. Soft aluminum would not stand up to a valve closing on it over and over, which is why the head carries hard seats. It is the valve guides, not the seats, that are aluminum bronze, and the seats are shrunk in, not screwed in.

  4. Q.04

    A Jabiru is going to fly with a propeller that does not meet its installation manual's requirements, which can upset the mixture. What should be done?

    FAA-H-8083-32B, ch. 11, p. 11-24

    1. AFit a richer main jet on your own judgment before it flies
    2. BFit an EGT gauge and watch the readings against the limits
    3. CNothing, since its carburetor already corrects the mixture
    SHOW THE ANSWER

    THE ANSWER IS B.

    Fit an EGT gauge and watch the readings against the limits

    The engine comes with jets to suit most installations, but a propeller outside the installation manual's requirements, or extreme temperatures, can affect the mixture. In that case an exhaust gas temperature gauge is fitted and monitored against the limits. If the readings fall outside the range, the carburetor settings are not changed without consulting Jabiru or its local authorized representative. The carburetor does adjust the mixture for altitude, but that does nothing about a mismatched propeller.

  5. Q.05

    A certificated Rotax with the overload clutch is in for its gearbox check, and the friction torque through the free rotation range works out to 12 Nm. What follows?

    FAA-H-8083-32B, ch. 11, p. 11-21

    1. AAccept it and fly, since any reading below the 60 Nm maximum is a pass
    2. BInspect, repair or overhaul the gearbox, as it is below the minimum
    3. CRetorque the propeller bolts, then run the same check once more
    SHOW THE ANSWER

    THE ANSWER IS B.

    Inspect, repair or overhaul the gearbox, as it is below the minimum

    The friction torque has to fall between 25 Nm and 60 Nm, which is 18.5 to 44.3 foot-pounds. 12 Nm is well short of the minimum, so the gearbox is inspected, repaired or overhauled to the manufacturer's instructions. Passing under the maximum is only half the test. Retorquing the propeller bolts is not the fix either: the friction being measured is in the gearbox's free rotation, felt with the crankshaft locked, so a low reading points to the gearbox.

  6. Q.06

    At an inspection on a Jabiru, a mechanic used to Lycomings gets out a timing light to check and set the ignition timing. What should you tell them?

    FAA-H-8083-32B, ch. 11, p. 11-10

    1. ATime each of the 2 distributors to its own plugs
    2. BSet the coil air gaps first, then time it with the light
    3. CNo timing adjustment is needed, as the timing is fixed
    SHOW THE ANSWER

    THE ANSWER IS C.

    No timing adjustment is needed, as the timing is fixed

    The Jabiru ignition is a transistorized electronic system with fixed timing, which removes the need for any timing adjustment. Its coils are fixed beside the flywheel and are energized by magnets on it, and its distributors only route the current, so there is nothing to time. The system is also fully redundant, self-generating and independent of the battery.

  7. Q.07

    On the pre-flight checks of a single-ignition Rotax 447, how is the ignition switch checked?

    FAA-H-8083-32B, ch. 11, p. 11-22

    1. AFlick it off and straight back on with the engine at idle
    2. BSwitch between the 2 ignition circuits and watch the rpm drop
    3. CLeave it alone, since single-ignition engines skip this check
    SHOW THE ANSWER

    THE ANSWER IS A.

    Flick it off and straight back on with the engine at idle

    For a single-ignition engine the check is to flick the ignition off and on again at idling, which shows the switch really does cut the ignition. Dual-ignition engines are checked by trying each of their 2 ignition circuits, and a single-ignition engine such as the 447 does not have 2 to try. Skipping the check would leave a switch that might not stop the engine.

  8. Q.08

    Before a long cross-country flight, you check the oil on a Rotax with a separate oil tank. Where should you bring the level to?

    FAA-H-8083-32B, ch. 11, p. 11-20

    1. AMidway between the marks, the same as for any flight
    2. BJust above the maximum mark, for a little extra margin
    3. CUp to the maximum mark, for more oil in reserve
    SHOW THE ANSWER

    THE ANSWER IS C.

    Up to the maximum mark, for more oil in reserve

    The level must sit between the 2 dipstick marks and never fall below the minimum. In standard operation it is about midway, but for longer flights the tank is filled to the maximum mark to give more oil in reserve. Going above the maximum is over-servicing, and the extra oil can escape through the breather. As always, the propeller is turned by hand first until air gurgles back into the tank, so the reading is true.

  9. Q.09

    An owner moving from a Lycoming to a Jabiru asks why there are no cylinder baffles or plenum chamber to look over at inspection. What does leaving them out give the mechanic?

    FAA-H-8083-32B, ch. 11, p. 11-11

    1. AA plenum seal that has to be checked at every inspection
    2. BA cleaner installation, easier to maintain and inspect
    3. CDucts that must come off before any cylinder can be seen
    SHOW THE ANSWER

    THE ANSWER IS B.

    A cleaner installation, easier to maintain and inspect

    Jabiru engines use ram-air ducts to carry air from the propeller to the critical areas, especially the cylinder heads and barrels. That does away with the baffles and plenum chamber that are the traditional way of cooling air-cooled aircraft engines, and the result is a cleaner engine installation that makes maintenance and inspection easier. With no plenum there is no plenum seal to check, and the design makes the engine easier to look over, not harder.

  10. Q.10

    The HKS 700T drives its propeller through a 2.13 to 1 reduction gearbox. At its 5,300 rpm takeoff rating, about how fast does the propeller turn?

    FAA-H-8083-32B, ch. 11, p. 11-9

    1. A2,488 rpm
    2. B2,650 rpm
    3. C11,289 rpm
    SHOW THE ANSWER

    THE ANSWER IS A.

    2,488 rpm

    Propeller speed is engine speed divided by the reduction ratio. 5,300 divided by 2.13 is about 2,488 rpm at the propeller flange. Dividing by 2 and dropping the .13 gives 2,650 rpm, and multiplying gives 11,289 rpm, faster than the engine, which a reduction gearbox cannot do.

We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.

04 AND THEN THE ORAL§ 65.79

How a missed code comes back at the oral

Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.III.A. The examiner reads those codes before your oral and practical.

The Powerplant oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Powerplant also carries 11 practical projects, each with 2 questions attached.

Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.

05 COMMON QUESTIONSFAQ

Questions people ask about light-sport aircraft engines

Q.01

How does a 2-stroke engine work?

It completes its cycle in 2 strokes of the piston, one turn of the crankshaft, so it fires on every revolution. Many are piston ported: the piston uncovers ports in the cylinder wall instead of opening valves, and some, such as the Rotax 582, use a rotary valve on the inlet.

Q.02

How is a 2-stroke engine lubricated?

On some engines the oil is mixed with the fuel in the tank. Others, such as the Rotax 503, use an oil injection system that keeps the oil in a separate tank and does not mix it into the fuel beforehand.

Q.03

What is a Rotax 912?

A 4-cylinder, 4-stroke, horizontally opposed engine. Its cylinder heads are cooled by both liquid and air, with air cooling mostly on the cylinders. It has low vibration and is the same weight as the 2-stroke Rotax 582 it often replaces in light aircraft.

Q.04

What ignition does the Rotax 582 use?

Dual ignition, a breakerless magneto capacitor discharge design. The 582 is a 2-cylinder inline 2-stroke with a rotary valve inlet and liquid cooled heads and cylinders, fed by dual piston type carburetors and a pneumatic fuel pump.

Q.05

How many light-sport aircraft engines questions are on the FAA A&P Powerplant test?

The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Reciprocating Engines subject area 5 to 15% of the Powerplant test, which is 5 to 15 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.

Q.06

Which FAA handbook chapter covers light-sport aircraft engines?

Chapter 11 of FAA-H-8083-32B, the Aviation Maintenance Technician Handbook: Powerplant, titled "Light-Sport Aircraft Engines". It runs from pages 11-1 to 11-25, and the FAA publishes the whole handbook free as a PDF.

FREE PLAN · NO CARD · 25 QUESTIONS TO START

The bank holds 233 light-sport aircraft engines questions.

Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.

Start free

Or answer a few first. The free FAA A&P practice test runs on the page, with no account.