AMP · PP-10 · FAA-H-8083-32B CH. 10
FAA A&P Powerplant: Engine Instrument, Inspection and Maintenance
For the FAA A&P Powerplant test, engine inspection and maintenance is chapter 10 of FAA-H-8083-32B, Engine Maintenance & Operation. Its main ACS subject area, Engine Inspection, is 5 to 10% of the test, or 5 to 10 of its 100 scored questions. Our question bank holds 508 questions on it, and the 10 below were written for this page.
Test shares and most-missed codes read from the FAA on 15 November 2026.
What FAA-H-8083-32B chapter 10 covers
Chapter 10 is Engine Maintenance & Operation. It covers reciprocating engine overhaul, from top overhaul to major overhaul, the inspection methods used on engine parts, cylinder compression testing, and troubleshooting, then how a reciprocating engine is operated on the ground and what affects how it runs.
It covers turbine engine maintenance and inspection, from the compressor and the combustion section to turbine blades, discs and nozzles, turbine engine operation and troubleshooting, and the engine instruments and warning systems a mechanic reads during a run, such as exhaust gas temperature and the tachometer.
It runs from pages 10-1 to 10-65 of the Aviation Maintenance Technician Handbook: Powerplant, which the FAA publishes free as a PDF.
How much of the FAA A&P Powerplant test it is
- 5 to 10%OF THE TESTACS area AM.III.C
- 5 to 10QUESTIONSof 100 scored
- 508IN OUR BANKquestions on this subject
The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Engine Inspection (AM.III.C) is 5 to 10% (5 to 10 questions) on the 100-question Powerplant test. Our Engine Instrument, Inspection and Maintenance questions also reach into Engine Instrument Systems (AM.III.D, 5 to 10%). The 13 ranges for the Powerplant test add up to anywhere from 65% to 140%, so they say how big an area can get, not how many questions you will see from it.
Engine Inspection is not ours alone to cover: our Engine Removal and Replacement questions are written to the same area.
No code in these areas is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.
Engine inspection and maintenance questions and answers
10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.
- Q.01
Engine cycles are among the most important factors in turbine engine life, along with EGT and engine speed. What generally counts as one cycle?
FAA-H-8083-32B, ch. 10, p. 10-59
- AOne takeoff and landing
- BOne hour of running at any power
- COne start, whether or not it lights
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
One takeoff and landing
The handbook names EGT, engine cycles and engine speed as some of the most important factors affecting turbine engine life, and a cycle is generally a takeoff and a landing. An hour of running is a measure of time, not a cycle, and a start that never lights is not a takeoff and landing. Even a few degrees of excess EGT shortens turbine component life, and excessive engine speed can cause premature wear.
- Q.02
When refacing valve seats, why does the handbook want enough stone holders on hand for every stone the job will use?
FAA-H-8083-32B, ch. 10, p. 10-13
- ASo each stone can turn at its own best speed
- BSo a stone never has to be dressed at all
- CSo stones need as little dressing as possible
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
So stones need as little dressing as possible
A seat stone is refaced with the diamond dresser when it is first put on its holder, and again whenever it is grooved or loaded. Every dressing wears the stone away, so dressing is kept to a minimum to conserve stones, and a holder for each stone saves dressing a stone again every time stones are swapped. Stones still need dressing at times, and the holder has nothing to do with how fast the stone turns.
- Q.03
At overhaul, an aluminum bearing surface shows a lot of fine scratching and some light scoring, but it measures within the table of limits and has no other defects. What is the call?
FAA-H-8083-32B, ch. 10, p. 10-4
- AReject it, since any scoring on a bearing surface rules it out
- BKeep it, since light marks like these do no harm within limits
- CHave it chrome-plated to cover the marks, then refit it
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Keep it, since light marks like these do no harm within limits
Considerable scratching and light scoring of aluminum bearing surfaces do no harm, and they are not a reason to reject the part as long as it falls within the clearances in the manufacturer's table of limits. A part inside those limits still has to be free of other serious defects. Plating a bearing surface to hide marks that do no harm would change its size and is no repair at all.
- Q.04
Inspecting a turbine engine's compressor guide vanes, you find a crack running inward from the outer airfoil on the concave face of a rubber-filled vane, with nothing to suggest pieces could break away. How does the handbook treat it?
FAA-H-8083-32B, ch. 10, p. 10-47
- AReject the vane, since any crack in a vane rejects it
- BWeld the crack closed, then refill the vane with rubber
- CIt can be an allowable crack, within the manual's limits
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
It can be an allowable crack, within the manual's limits
The handbook allows cracks on the concave surfaces of rubber-filled vanes that run inward from the outer airfoil, as long as nothing suggests pieces breaking away. What rejects a vane is a crack that branches or forks so that a piece of metal could break free and fall into the compressor. No vane is repaired by welding, brazing, straightening or soldering, and the specific manufacturer's current limits always make the final call.
- Q.05
An engine with a torquemeter is given its magneto check. In what situation does the torquemeter's drop give more positive evidence of the power change than the rpm reading does?
FAA-H-8083-32B, ch. 10, p. 10-27
- AWhen the propeller is set to high pitch for the check
- BWhen the tachometer scale is graduated coarsely
- CWhen both magnetos are left on throughout the check
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
When the tachometer scale is graduated coarsely
On the magneto check, a drop in torquemeter pressure is a good supplement to the change in rpm. Where the tachometer scale is graduated coarsely, the torquemeter may show the power change on each magneto more positively than the rpm does. The check uses the propeller in its low fixed-pitch position to absorb the power, and it means switching from both magnetos to each one in turn; with both left on there is no drop to see.
- Q.06
Torquing a cylinder's hold-down nuts with a slow, steady pull, you reach the value in the table of torque values. What do you do next with the wrench?
FAA-H-8083-32B, ch. 10, p. 10-43
- ALet go at once, so the nut is not taken past its torque
- BHold that torque until the nut turns no more, then safety it
- CBack the nut off a quarter turn and pull it up to torque again
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Hold that torque until the nut turns no more, then safety it
Apply the torque slowly and steadily, then hold the tension on the wrench long enough to be sure the nut or cap-screw tightens no more at that value. A nut can often turn as much as another quarter turn while the torque is held, which is why letting go at once can leave it short. Backing it off and pulling it up again is not the procedure. Once torqued, it is safetied the way the manufacturer's manual says.
- Q.07
Fitting a replacement cylinder, you notice an international orange paint band around the barrel between the mounting flange and the lowest cooling fin. What does it tell you?
FAA-H-8083-32B, ch. 10, p. 10-41
- AThe bore is chrome-plated, so chrome-plated rings must not go in
- BThe cylinder has been reground to its first oversize
- CThe bore is plain steel, so it must be fitted with chrome-plated rings
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
The bore is chrome-plated, so chrome-plated rings must not go in
A paint band in that spot, usually international orange, is how a chrome-plated cylinder is marked. Chrome-plated piston rings are not used in a chrome-plated bore. The matched assembly comes with the right rings, and if one breaks while you fit the cylinder, the marking tells you which ring goes back in. Cylinder size can also be shown by a color code in the same place, but orange is the chrome mark, not an oversize or a plain steel bore.
- Q.08
A turbine engine was shut down straight after a long high-rpm trim run on the ground, and now its rotor will not turn by hand. What should you do?
FAA-H-8083-32B, ch. 10, p. 10-59
- AMotor it on the starter to break the wheels free
- BLeave it alone until it has cooled enough to free the wheels
- CCool the turbine case with water so it lets go of the wheels
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Leave it alone until it has cooled enough to free the wheels
The turbine case cools faster than the massive turbine wheels, so after prolonged high-speed running it can shrink onto them, and in the worst case the wheels squeal or seize. That is why a cooling period is run before shutdown. If they do seize, no harm normally results as long as nobody tries to turn the engine over until it has cooled enough to free the wheels. Forcing it with the starter risks damage, and chilling the case only makes it shrink tighter.
- Q.09
A cylinder with a standard bore of 5.125 inches is to finish 0.010 inch oversize, honed after grinding. Allowing the usual stock for honing, what regrind size do you order?
FAA-H-8083-32B, ch. 10, p. 10-18
- A5.134 inches
- B5.135 inches
- C5.136 inches
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
5.134 inches
The regrind size is worked out from the standard bore. 5.125 plus 0.010 oversize is a finished bore of 5.135 inches. The hone takes off about 0.001 inch, so the cylinder is ground to 5.134 and honed out to 5.135. Ordering 5.135 leaves nothing for the hone, and 5.136 adds the allowance instead of taking it away.
- Q.10
During a hot section inspection, a combustion chamber slips from your hands and drops onto the concrete floor. It looks undamaged. What should happen before it is used again?
FAA-H-8083-32B, ch. 10, p. 10-50
- AScrap it, since any dropped hot section part is condemned
- BRefit it, since it shows no damage after the drop
- CInspect it thoroughly for minute cracks that could grow
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Inspect it thoroughly for minute cracks that could grow
Any cover or chamber dropped on a hard surface or mishandled is inspected thoroughly for minute cracks. Such cracks may lengthen over time and then open, creating a hazard, so looking undamaged is not enough reason to refit it. The handbook calls for an inspection, not automatic scrapping; throwing a part away after a drop is the rule for a spark plug, whose insulator can crack where no inspection will show it.
We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.
How a missed code comes back at the oral
Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.III.C or AM.III.D. The examiner reads those codes before your oral and practical.
The Powerplant oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Powerplant also carries 11 practical projects, each with 2 questions attached.
Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.
Questions people ask about engine inspection and maintenance
Q.01What does a differential compression test show?
How well a cylinder holds pressure. With the piston at top center on the compression stroke, regulated air at 80 psi is fed into the cylinder from a 100 to 150 psi supply, and the drop in pressure shows how much is leaking past the rings or valves. The test is done soon after shutdown, while the rings and walls are still well lubricated.
Q.02What is the difference between a top overhaul and a major overhaul?
A top overhaul is an overhaul of the parts on top of the crankcase, the cylinders, pistons, rings and valve mechanism, without completely dismantling the engine. A major overhaul is the complete reconditioning of the engine: it is taken right apart, cleaned, inspected, and each part is overhauled to the manufacturer’s instructions.
Q.03What is a hot start on a turbine engine?
A start in which the exhaust gas starting temperature limit is exceeded. The start is aborted. A good start shows first as a rise in exhaust gas temperature, and if the engine does not light within the time given, the start is aborted too. Following the engine’s own starting procedure is what avoids hot and hung starts.
Q.04What is a hot section inspection?
An inspection and cleaning of the turbine and combustion section, the parts of a turbine engine that run hottest. Cracking is one of the things found most often, and the manufacturer’s manuals decide whether a crack is within limits or allowed at all.
Q.05How many engine inspection and maintenance questions are on the FAA A&P Powerplant test?
The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Engine Inspection subject area 5 to 10% of the Powerplant test, which is 5 to 10 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it. Our Engine Instrument, Inspection and Maintenance questions also reach into Engine Instrument Systems (5 to 10%).
Q.06Which FAA handbook chapter covers engine inspection and maintenance?
Chapter 10 of FAA-H-8083-32B, the Aviation Maintenance Technician Handbook: Powerplant, titled "Engine Maintenance & Operation". It runs from pages 10-1 to 10-65, and the FAA publishes the whole handbook free as a PDF.
Read the documents, not us
Every fact on this page was read from these on 19 August 2026 and 15 November 2026. They are the authority and we are the summary. If we and one of them disagree, they are right.
- FAA-H-8083-32B, Aviation Maintenance Technician Handbook: Powerplant, chapter 10www.faa.gov
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standardswww.faa.gov
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards: the written test blueprints (pages 13 and 14) and chapters 6 and 7www.faa.gov
- FAA, Frequently Missed Knowledge Test ACS Codes, 2nd Quarter CY25www.faa.gov
More FAA A&P Powerplant subjects
FREE PLAN · NO CARD · 25 QUESTIONS TO START
The bank holds 508 engine inspection and maintenance questions.
Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.
Start freeOr answer a few first. The free FAA A&P practice test runs on the page, with no account.