PrepAMT Academy

AMP · PP-09 · FAA-H-8083-32B CH. 9

FAA A&P Powerplant: Engine Fire Protection Systems

For the FAA A&P Powerplant test, engine fire protection systems is chapter 9 of FAA-H-8083-32B, Engine Fire Protection Systems. Its ACS subject area, Engine Fire Protection Systems, is 5 to 10% of the test, or 5 to 10 of its 100 scored questions. Our question bank holds 173 questions on it, and the 10 below were written for this page.

Test shares and most-missed codes read from the FAA on 15 November 2026.

01 WHAT IT COVERSFAA-H-8083-32B · CH. 9

What FAA-H-8083-32B chapter 9 covers

Chapter 9 covers fire protection for the engine installation: the fire zones and the turbine engine failures that start fires, and the detection systems, from thermal switches and thermocouples to continuous loop, pneumatic and optical detectors, with single and dual loop operation and how each is tested.

It then covers extinguishing: the agents, the containers and their discharge valves and cartridges, the flight deck fire handles and switches, and the inspection, maintenance and troubleshooting of detection and extinguishing systems.

It runs from pages 9-1 to 9-19 of the Aviation Maintenance Technician Handbook: Powerplant, which the FAA publishes free as a PDF.

02 SHARE OF THE TESTFAA-G-ACS-1 · BLUEPRINT

How much of the FAA A&P Powerplant test it is

  • 5 to 10%OF THE TESTACS area AM.III.E
  • 5 to 10QUESTIONSof 100 scored
  • 173IN OUR BANKquestions on this subject

The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Engine Fire Protection Systems (AM.III.E) is 5 to 10% (5 to 10 questions) on the 100-question Powerplant test. The 13 ranges for the Powerplant test add up to anywhere from 65% to 140%, so they say how big an area can get, not how many questions you will see from it.

No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.

03 EXAMPLE QUESTIONSWRITTEN FOR THIS PAGE

Engine fire protection systems questions and answers

10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.

  1. Q.01

    An engine compartment heats up slowly over a long ground run until it is dangerously hot, with no flame. Which kind of detection system is built to warn of that?

    FAA-H-8083-32B, ch. 9, p. 9-3

    1. AA continuous-loop system
    2. BA thermocouple system
    3. CAn infrared flame detector
    SHOW THE ANSWER

    THE ANSWER IS A.

    A continuous-loop system

    Continuous-loop systems are overheat systems. They complete a circuit when the element reaches a set temperature and have no rate-of-rise sensitivity, so a slow climb to a dangerous level still sets them off. A thermocouple system is the opposite: it warns only when the hot junction heats faster than the reference junction, and it gives no warning when an engine slowly overheats. A flame detector looks for the radiation of a hydrocarbon flame, and here there is none.

  2. Q.02

    A Kidde loop responds to a kind of average along its whole length, so a short hot spot on its route does not set off a false alarm. Where does that let its alarm point be set?

    FAA-H-8083-32B, ch. 9, p. 9-5

    1. AWell above the hottest spot the element runs past
    2. BBelow the coolest point anywhere along the loop
    3. CClose to the zone's maximum general ambient temperature
    SHOW THE ANSWER

    THE ANSWER IS C.

    Close to the zone's maximum general ambient temperature

    Because the element works on the sum of its whole length, it can be routed close to spots that are normally hotter than the alarm temperature without causing a false alarm. That lets the alarm point be set close to the maximum general ambient temperature, which makes the loop more sensitive to a general overheat or fire. Setting it above the hottest local spot would throw that sensitivity away, and the coolest point of the loop tells you nothing about the zone as a whole.

  3. Q.03

    A CO2 extinguisher kept on the ramp at a very cold northern base has had a booster charge of nitrogen added. Why?

    FAA-H-8083-32B, ch. 9, p. 9-7

    1. AIn extreme cold, CO2 alone may lack the pressure to discharge
    2. BNitrogen stops the CO2 from turning to snow as it leaves the nozzle
    3. CNitrogen stops the CO2 reacting with the hot metal it lands on
    SHOW THE ANSWER

    THE ANSWER IS A.

    In extreme cold, CO2 alone may lack the pressure to discharge

    CO2 normally provides its own pressure to discharge from its container. In extremely cold climates that pressure can fall too low, so a booster charge of nitrogen may be added to winterize the extinguisher. The dry ice snow is simply what CO2 does as it expands and cools on discharge, and nitrogen does not prevent it. CO2 does not react with most substances, so there is nothing there for nitrogen to stop; it is only there to push the CO2 out.

  4. Q.04

    Replacing a squib on a Boeing 777 engine fire bottle, you see that the container carries 2 squibs in its discharge assembly. What is the second squib for?

    FAA-H-8083-32B, ch. 9, p. 9-16

    1. AIt is a spare that fires if the first squib fails
    2. BIt sends that bottle's agent to the other engine
    3. CIt opens the safety relief port if the bottle overheats
    SHOW THE ANSWER

    THE ANSWER IS B.

    It sends that bottle's agent to the other engine

    Halon from either 777 bottle can be discharged to the right or the left engine, so each container has 2 squibs, one for each engine. A squib is an electrically fired explosive device that sends a slug through the breakable disc, and nitrogen pressure in the bottle then pushes the Halon out. Neither squib is a spare for the other, and a bottle that builds up too much pressure vents through its safety relief and fill port, not through a squib.

  5. Q.05

    Each engine on a transport airplane has 2 complete fire detection loops, wired so that both must signal before the crew gets a fire warning. What is that arrangement mainly for?

    FAA-H-8083-32B, ch. 9, p. 9-6

    1. AGiving a faster warning, since 2 loops sense a fire sooner than one
    2. BGuarding against false fire warnings, whatever their cause
    3. CLetting one loop give the overheat warning and the other the fire warning
    SHOW THE ANSWER

    THE ANSWER IS B.

    Guarding against false fire warnings, whatever their cause

    A dual-loop system is really 2 complete basic fire detection systems, with their outputs joined so that both have to signal before a fire warning shows. The handbook calls this AND logic. It makes a false fire warning far less likely, whatever is behind it, because one faulty loop cannot raise the warning by itself. It does not make the warning quicker, and the overheat and fire levels come from 2 set points on the same loop, not from one loop each.

  6. Q.06

    During a ground run, a brief surge of heat takes a Kidde loop's resistance down to its overheat set point. About 3 seconds later the compartment cools and the resistance climbs back past the reset point. On a typical system, what happens to the overheat indication?

    FAA-H-8083-32B, ch. 9, p. 9-4

    1. AIt never comes on, as the overheat delay had not run out
    2. BIt comes on at once, then goes out when the loop recovers
    3. CIt comes on and stays on until the test switch is pressed
    SHOW THE ANSWER

    THE ANSWER IS A.

    It never comes on, as the overheat delay had not run out

    A typical Kidde control unit has a time delay of about 10 seconds built into its overheat indication, so the resistance has to stay down at the overheat set point or lower for that long before the indication appears. Here it recovered after about 3 seconds, well inside the delay, so the overheat indication never comes on. Nothing latches either: once the core cools and its resistance rises to the reset point, any fire or overheat indication goes away by itself, without the test switch.

  7. Q.07

    Fractured or thrown turbine blades can lead to an overheat or a fire. On a multistage turbine, which blade failure is usually much more severe?

    FAA-H-8083-32B, ch. 9, p. 9-1

    1. AA failure in the last stage, nearest the tail cone
    2. BA failure in the middle stages, where the gas is hottest
    3. CA failure in the forward stages of the turbine
    SHOW THE ANSWER

    THE ANSWER IS C.

    A failure in the forward stages of the turbine

    Mechanical failures such as fractured or thrown blades can cause overheat conditions or fires, and on a multistage turbine a failure of the forward stages is usually much more severe, since whatever breaks loose at the front has every later stage behind it. Thrown blades can puncture the tail cone or the turbine case and cut lines carrying flammable fluids. The gas is hottest where it enters the turbine, not in the middle stages.

  8. Q.08

    In a Boeing 777 engine fire, the crew pulls the fire switch, the engine stops and is isolated, and the fire warnings then go away. What does the handbook procedure say about the bottles?

    FAA-H-8083-32B, ch. 9, p. 9-17

    1. ATurn the switch to DISCH 1 and hold it, then to DISCH 2
    2. BNo bottle is called for, since the warnings have gone away
    3. CPush the fire override switch so a bottle fires by itself
    SHOW THE ANSWER

    THE ANSWER IS B.

    No bottle is called for, since the warnings have gone away

    Pulling the switch stops the engine and isolates it from the aircraft systems. The handbook calls for turning the switch to DISCH 1 or DISCH 2, and holding it against the stop for one second, only if the fire warnings do not go away when the switch is pulled. The other DISCH position fires the other bottle, and is used only if the first bottle does not put the fire out. The override switch only releases a switch whose solenoid has not energized; it fires nothing.

  9. Q.09

    For night flying, the crew switches the warning lights to dim. On this thermal switch fire warning system, several fire circuits are wired through the one dimming relay. What happens to their lights?

    FAA-H-8083-32B, ch. 9, p. 9-2

    1. AOnly the light of the circuit that last gave a warning is dimmed
    2. BThey dim, and the fire warnings stay cut out until the lights go back to bright
    3. CEvery warning light wired through that relay dims at the same time
    SHOW THE ANSWER

    THE ANSWER IS C.

    Every warning light wired through that relay dims at the same time

    Energizing the dimming relay changes each circuit wired through it so that a resistor sits in series with its warning light, which lowers the brightness. Where several circuits share the one dimming relay, all of their warning lights can be dimmed together. Each light stays in its circuit, only with the resistor added, so a dimmed light still comes on when one of its thermal switches closes, and the relay does not pick out a single circuit.

  10. Q.10

    A turbine engine fire starts during a ground start. Fuel is shut off, the engine is motored, and CO2 goes into the inlet duct while it turns, but the fire keeps burning. What now?

    FAA-H-8083-32B, ch. 10, p. 10-57

    1. ATurn the fuel back on so the engine can run it clear
    2. BSecure all switches and leave the aircraft
    3. CTry another start so the engine blows it out
    SHOW THE ANSWER

    THE ANSWER IS B.

    Secure all switches and leave the aircraft

    For a turbine fire during a ground start, the fuel shutoff lever goes to off and the engine is cranked or motored until the fire is expelled. If it persists, CO2 can go into the inlet duct while the engine is cranked. If the fire still cannot be put out, all switches are secured and everyone leaves the aircraft. Turning the fuel back on, or making another start, would only feed the fire more fuel.

We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.

04 AND THEN THE ORAL§ 65.79

How a missed code comes back at the oral

Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.III.E. The examiner reads those codes before your oral and practical.

The Powerplant oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Powerplant also carries 11 practical projects, each with 2 questions attached.

Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.

05 COMMON QUESTIONSFAQ

Questions people ask about engine fire protection systems

Q.01

What is a fire zone?

An area or region of the aircraft that the manufacturer designates as needing fire detection, fire extinguishing equipment, or both, and a high degree of fire resistance. On transport and commuter aircraft, the engine fire zones are protected by a fixed, permanently installed system, not just a hand-held extinguisher.

Q.02

What happens when an engine fire switch is operated?

The engine stops because the fuel control shuts off, the engine is isolated from the aircraft’s systems, and the extinguishing system is armed. Some fire switches are pulled and turned, others are pushed under a guard, and a lock keeps the switch from moving until a fire has been detected.

Q.03

How does a thermocouple fire warning system work?

It works on the rate of temperature rise, not on a set temperature. Thermocouples in series with a sensitive relay control the warning lights, and a fast rise sets them off. It gives no warning when an engine overheats slowly or when a short circuit develops.

Q.04

What is a dual loop fire detection system?

In effect, 2 complete fire detection systems whose signals are connected so that both must sense a fire before the warning comes on, which makes false warnings far less likely. If one loop fails its preflight test, a selector switch takes it out, and the other loop alone gives the warning.

Q.05

How many engine fire protection systems questions are on the FAA A&P Powerplant test?

The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Engine Fire Protection Systems subject area 5 to 10% of the Powerplant test, which is 5 to 10 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.

Q.06

Which FAA handbook chapter covers engine fire protection systems?

Chapter 9 of FAA-H-8083-32B, the Aviation Maintenance Technician Handbook: Powerplant, titled "Engine Fire Protection Systems". It runs from pages 9-1 to 9-19, and the FAA publishes the whole handbook free as a PDF.

FREE PLAN · NO CARD · 25 QUESTIONS TO START

The bank holds 173 engine fire protection systems questions.

Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.

Start free

Or answer a few first. The free FAA A&P practice test runs on the page, with no account.