PrepAMT Academy

AMP · PP-01 · FAA-H-8083-32B CH. 1

FAA A&P Powerplant: Reciprocating and Turbine Engines

For the FAA A&P Powerplant test, reciprocating and turbine engines is chapter 1 of FAA-H-8083-32B, Aircraft Engines. Its main ACS subject area, Reciprocating Engines, is 5 to 15% of the test, or 5 to 15 of its 100 scored questions. Our question bank holds 426 questions on it, and the 10 below were written for this page.

Test shares and most-missed codes read from the FAA on 15 November 2026.

01 WHAT IT COVERSFAA-H-8083-32B · CH. 1

What FAA-H-8083-32B chapter 1 covers

Chapter 1 covers aircraft engines from the ground up: what an engine has to do, the reciprocating engine types by cylinder arrangement, inline, opposed, V-type and radial, and the parts of a reciprocating engine, from the crankcase, crankshaft, connecting rods, pistons and rings to the cylinders, valves and valve operating mechanism, bearings and propeller reduction gearing, with the operating cycles, power and efficiency.

The second half is the gas turbine: turbojet, turbofan, turboprop and turboshaft engines and their sections, from the inlet and compressor, centrifugal and axial, through the combustion section to the turbine, exhaust and bearings, with how turbine engines are rated and what affects their performance.

It runs from pages 1-1 to 1-61 of the Aviation Maintenance Technician Handbook: Powerplant, which the FAA publishes free as a PDF.

02 SHARE OF THE TESTFAA-G-ACS-1 · BLUEPRINT

How much of the FAA A&P Powerplant test it is

  • 5 to 15%OF THE TESTACS area AM.III.A
  • 5 to 15QUESTIONSof 100 scored
  • 426IN OUR BANKquestions on this subject

The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Reciprocating Engines (AM.III.A) is 5 to 15% (5 to 15 questions) on the 100-question Powerplant test. Our Reciprocating and Turbine Engines questions also reach into Turbine Engines (AM.III.B, 5 to 10%). The 13 ranges for the Powerplant test add up to anywhere from 65% to 140%, so they say how big an area can get, not how many questions you will see from it.

Reciprocating Engines is not ours alone to cover: our Engine Removal and Replacement and Light-Sport Aircraft Engines questions are written to the same area.

No code in these areas is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.

03 EXAMPLE QUESTIONSWRITTEN FOR THIS PAGE

Reciprocating and turbine engines questions and answers

10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.

  1. Q.01

    A reaction-impulse turbine blade combines the 2 basic blade designs along its length. How is it shaped from root to tip?

    FAA-H-8083-32B, ch. 1, p. 1-47

    1. ABucket-like near the root, turning into an airfoil toward the tip
    2. BAirfoil-shaped near the root, turning into a bucket toward the tip
    3. CBucket-like along its whole length, with a twist near the tip
    SHOW THE ANSWER

    THE ANSWER IS A.

    Bucket-like near the root, turning into an airfoil toward the tip

    An impulse blade, also called a bucket, is driven by the gas stream striking it and being turned, while a reaction blade works like an airfoil, driven by gas flowing past it at an angle. The reaction-impulse blade has more of the bucket shape at its root and more of the airfoil shape over its outer half, toward the tip. Swapping those ends, or keeping the bucket shape all the way out, is not how it is built.

  2. Q.02

    On a pusher airplane the engine sits with its propeller facing aft. A note in the engine manual refers to the engine's left side. Which side of the airplane is that on?

    FAA-H-8083-32B, ch. 1, p. 1-15

    1. AThe airplane's left side, since engine sides follow the airframe
    2. BEither side, depending on which way the crankshaft turns
    3. CThe airplane's right side, as seen from the accessory end
    SHOW THE ANSWER

    THE ANSWER IS C.

    The airplane's right side, as seen from the accessory end

    Engine directions belong to the engine, not the airframe. The propeller end is always the front and the accessory end the rear, and left and right are always named as seen from the rear, the accessory end, looking toward the propeller. On a pusher that view looks aft, so the engine's left side is on the airplane's right. Crankshaft rotation is described from that same view; it does not decide which side is which.

  3. Q.03

    Inspecting the exhaust section of a turbine engine, you find the small hole in the exit tip of the inner cone plugged with carbon. What has the blockage stopped?

    FAA-H-8083-32B, ch. 1, p. 1-51

    1. AFuel draining out of the exhaust duct after a false start
    2. BAir flowing forward inside the cone to cool the turbine wheel's face
    3. CA path for the borescope to view the last turbine stage from behind
    SHOW THE ANSWER

    THE ANSWER IS B.

    Air flowing forward inside the cone to cool the turbine wheel's face

    On engines that have it, the small hole in the tip of the inner cone lets gas from the aft end of the cone, where the pressure is fairly high, flow forward inside the cone and onto the face of the turbine wheel to cool it. The spinning wheel keeps the pressure low at its face, so the flow is sure, and the gas rejoins the main stream through the gap between the disc and the cone. Plug the hole and that cooling stops. Fuel drains and borescope ports are separate fittings.

  4. Q.04

    Some crankcases are split so that every main bearing is held in the one section that carries the cylinders, instead of half in each section. What does that arrangement allow?

    FAA-H-8083-32B, ch. 1, p. 1-8

    1. AFewer main bearings, since each one is now held whole in a single section
    2. BRemoving the other section for inspection with the bearing adjustment undisturbed
    3. CSome misalignment between the crankshaft and its bearings without any harm
    SHOW THE ANSWER

    THE ANSWER IS B.

    Removing the other section for inspection with the bearing adjustment undisturbed

    A crankcase split along its length can hold the main bearings 2 ways. Split through the crankshaft, each section carries half of every bearing. Put all the bearings in the section that carries the cylinders, and the other section can be taken off to look inside without touching the bearing adjustment. That is the point of the design. The crankshaft is still generally carried by a main bearing between each throw, so there are no fewer of them, and the case still has to be rigid enough to keep the crankshaft and its bearings in line.

  5. Q.05

    At overhaul you find a hollow push rod with both of its drilled ball ends packed solid with sludge. Which parts would that have left short of oil?

    FAA-H-8083-32B, ch. 1, p. 1-21

    1. AThe rocker arm bearing and the valve stem guide
    2. BThe tappet roller and the cam lobe that it rides against
    3. CThe piston pin bosses and the walls of that cylinder
    SHOW THE ANSWER

    THE ANSWER IS A.

    The rocker arm bearing and the valve stem guide

    Oil under pressure comes up through a hole in the tappet, runs through the hollow push rod and out through its drilled ball ends, and lubricates the ball ends, the rocker arm bearing and the valve stem guide. With the ball ends blocked, those parts go without. The tappet and cam are fed on the engine side before the oil ever reaches the push rod, and the piston pins and cylinder walls get their oil inside the crankcase.

  6. Q.06

    On a test stand fitted with a Prony brake, a trainee tightens the brake until the engine stalls, and the scale then shows a large force. What brake horsepower can be worked out from that reading?

    FAA-H-8083-32B, ch. 1, p. 1-32

    1. AThe most the engine can make, since the torque reading is at its highest
    2. BIts friction horsepower, since only the brake's friction is being measured
    3. CNone, since a stalled engine has torque to measure but no rpm
    SHOW THE ANSWER

    THE ANSWER IS C.

    None, since a stalled engine has torque to measure but no rpm

    Brake horsepower comes from 2 readings taken together: the torque, which is the scale force times the arm length, and the rpm. With the engine stalled there may be plenty of torque on the scale, but the shaft is not turning, so there is no power to work out. With no load at all the engine runs away and there is no torque instead. Friction horsepower is power lost inside the engine, not the grip of the brake, and the highest torque is not the highest power.

  7. Q.07

    On some turbine inlet nozzles the vanes are welded or riveted into their inner and outer shrouds. How is that kind of nozzle allowed to grow with heat without warping the vanes?

    FAA-H-8083-32B, ch. 1, p. 1-47

    1. AEach vane sits loose in an oversize slot shaped to its airfoil
    2. BThe inner or the outer shroud ring is cut into segments
    3. CThe vanes are made of a ceramic that does not grow with heat
    SHOW THE ANSWER

    THE ANSWER IS B.

    The inner or the outer shroud ring is cut into segments

    Turbine nozzle vanes see fast temperature changes, so the assembly has to be free to expand or it distorts. When the vanes are welded or riveted in place, either the inner or the outer shroud ring is cut into segments, and the saw cuts between the segments give the room to grow. Loose vanes in oversize slots are the other method, which welded vanes rule out, and no vane material stops expanding when it heats.

  8. Q.08

    2 engines each drive the same model of oil-operated constant-speed propeller, one with its governor on the nose section and one with it on the rear section. What drawback comes with the rear-mounted governor?

    FAA-H-8083-32B, ch. 1, p. 1-6

    1. AA slower-turning governor drive, so it senses rpm less precisely
    2. BMore heat from the exhaust, which thins the governor's oil supply
    3. CLonger oil passages between the governor and the propeller
    SHOW THE ANSWER

    THE ANSWER IS C.

    Longer oil passages between the governor and the propeller

    A governor on the rear section works, but it complicates the installation when the propeller is worked by oil pressure, because the oil has to travel the whole length of the engine between the governor and the propeller. That is why, with a hydraulically operated propeller, it is good practice to put the governor on the nose section as close to the propeller as possible. Nothing about the rear position changes how the governor senses rpm or how hot its oil runs.

  9. Q.09

    You are fitting a turbine blade into a disc that holds its blades by peening, and the blade's fir-tree root has a small notch ground in its edge. Once the blade is in its slot, what locks it there?

    FAA-H-8083-32B, ch. 1, p. 1-49

    1. ADisc metal, flowed into the notch by a punch mark in the disc beside it
    2. BThe notch itself, peened shut so the blade root swells tight in its slot
    3. CNothing more, since the notch only shows which way round the blade goes
    SHOW THE ANSWER

    THE ANSWER IS A.

    Disc metal, flowed into the notch by a punch mark in the disc beside it

    Peening is one of the common ways of holding turbine blades in their fir-tree slots. A small notch is ground in the edge of the blade root before it goes in. Once the blade is in place, a small punch mark is made in the disc next to the notch, and that flows the disc metal into it and locks the blade. The tool is much like a center punch. The blade itself is not peened, and the notch is not a marker; blades with a stop at one end of the root are the kind that go in one way only.

  10. Q.10

    What design change has brought the greatest gain in air cooling on modern cylinder heads?

    FAA-H-8083-32B, ch. 1, p. 1-15

    1. ASpacing the fins wider apart, so more air flows between them
    2. BMaking the fins thicker, so each one carries away more heat
    3. CMaking the fins thinner and deeper, which adds fin area
    SHOW THE ANSWER

    THE ANSWER IS C.

    Making the fins thinner and deeper, which adds fin area

    Heat leaves a cylinder head through the surface of its fins, so what counts is fin area. The greatest improvement has come from making the fins thinner and deeper, which packs more area into the same space; modern fins taper from 0.090 inch at the base to 0.060 inch at the tip. Aluminum alloy suits this, since it casts and machines well into deep, closely spaced fins. Thicker fins add weight without adding area, and spacing them wider leaves room for fewer.

We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.

04 AND THEN THE ORAL§ 65.79

How a missed code comes back at the oral

Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.III.A or AM.III.B. The examiner reads those codes before your oral and practical.

The Powerplant oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Powerplant also carries 11 practical projects, each with 2 questions attached.

Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.

05 COMMON QUESTIONSFAQ

Questions people ask about reciprocating and turbine engines

Q.01

What are the strokes of a 4-stroke reciprocating engine?

Intake, compression, power and exhaust. The crankshaft turns 720 degrees, 2 full revolutions, for each complete cycle, so each cylinder fires once every 2 turns of the crankshaft.

Q.02

What is valve overlap?

The time at the end of the exhaust stroke and the start of the intake stroke when the intake and exhaust valves are both open. It improves volumetric efficiency, helps cool the cylinder from inside with the incoming mixture, and helps scavenge the burned gases.

Q.03

What is the difference between a turbofan and a turbojet?

In a turbojet all of the air goes through the core of the engine. A turbofan has a fan that also moves air around the core, and how much is bypassed sets its bypass ratio. On a high bypass turbofan the fan makes most of the thrust.

Q.04

What are the 2 kinds of turbine engine compressor?

The centrifugal flow compressor, which picks up the air and accelerates it outward, through an impeller and a diffuser, and the axial flow compressor, which compresses the air while it keeps moving in its original direction, through rows of rotating and stationary blades. Some engines use both.

Q.05

How many reciprocating and turbine engines questions are on the FAA A&P Powerplant test?

The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Reciprocating Engines subject area 5 to 15% of the Powerplant test, which is 5 to 15 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it. Our Reciprocating and Turbine Engines questions also reach into Turbine Engines (5 to 10%).

Q.06

Which FAA handbook chapter covers reciprocating and turbine engines?

Chapter 1 of FAA-H-8083-32B, the Aviation Maintenance Technician Handbook: Powerplant, titled "Aircraft Engines". It runs from pages 1-1 to 1-61, and the FAA publishes the whole handbook free as a PDF.

FREE PLAN · NO CARD · 25 QUESTIONS TO START

The bank holds 426 reciprocating and turbine engines questions.

Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.

Start free

Or answer a few first. The free FAA A&P practice test runs on the page, with no account.