AMP · PP-02 · FAA-H-8083-32B CH. 2
FAA A&P Powerplant: Engine Fuel and Fuel Metering Systems
For the FAA A&P Powerplant test, engine fuel and fuel metering systems is chapter 2 of FAA-H-8083-32B, Engine Fuel & Fuel Metering Systems. Its ACS subject area, Engine Fuel and Fuel Metering Systems, is 5 to 10% of the test, or 5 to 10 of its 100 scored questions. Our question bank holds 340 questions on it, and the 10 below were written for this page.
Test shares and most-missed codes read from the FAA on 15 November 2026.
What FAA-H-8083-32B chapter 2 covers
Chapter 2 starts with what an engine fuel system has to do and the parts that feed it, then the float carburetor and its systems, main metering, idling, accelerating, mixture control and economizer, with carburetor icing, and the pressure injection carburetor.
It covers fuel injection for reciprocating engines, then turbine engine fuel controls, hydromechanical and electronic up to FADEC, and the inspection, maintenance and troubleshooting of fuel metering systems.
It runs from pages 2-1 to 2-46 of the Aviation Maintenance Technician Handbook: Powerplant, which the FAA publishes free as a PDF.
How much of the FAA A&P Powerplant test it is
- 5 to 10%OF THE TESTACS area AM.III.I
- 5 to 10QUESTIONSof 100 scored
- 340IN OUR BANKquestions on this subject
The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Engine Fuel and Fuel Metering Systems (AM.III.I) is 5 to 10% (5 to 10 questions) on the 100-question Powerplant test. The 13 ranges for the Powerplant test add up to anywhere from 65% to 140%, so they say how big an area can get, not how many questions you will see from it.
No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.
Engine fuel and fuel metering systems questions and answers
10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.
- Q.01
On a fuel hose you find the ends have flared out a little just beyond the clamps. Nothing is leaking, and the hose is still soft and sound. What do you do?
FAA-H-8083-32B, ch. 2, p. 2-32
- ALeave it, since flared ends are not a fault unless there is leakage
- BReplace the hose, since flared ends show the plies have separated
- CTighten both clamps further until the flared ends are pulled back flat
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Leave it, since flared ends are not a fault unless there is leakage
Some hoses flare a little at the ends beyond their clamps, and on its own that is not an unsatisfactory condition; it only matters if there is leakage. A hose is replaced when its plies have separated, when it shows excessive cold flow, when it has gone hard and inflexible, or when it has collapsed at a bend, and none of that is the case here. Cranking the clamps down further would only add to cold flow.
- Q.02
During a fuel system inspection you run each of an airplane's 4 boost pumps in turn to check for leaks, watching the ammeter. 3 draw about the same current and the 4th draws far more. What do you make of it?
FAA-H-8083-32B, ch. 2, p. 2-31
- AIt is normal, since the pump farthest from the battery always draws most
- BThat pump has a problem and needs a closer look
- CThe ammeter is faulty, since pumps of one type always draw a fixed current
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
That pump has a problem and needs a closer look
Boost pumps are run during the inspection to pressurize the system and show up any leaks, and the ammeter or load meter is read for each one. Pumps doing the same job should read about the same, so one that draws far more than the others has something wrong with it and needs a closer look. The ammeter read the other 3 normally, and a pump's current changes with the load it is working against, so neither of the other ideas holds.
- Q.03
Inspecting an electric booster pump, you find that its drain line sags into a low loop where fuel sits. What do you do about the line?
FAA-H-8083-32B, ch. 2, p. 2-32
- ACap its open end so the fuel held in the loop cannot drip out
- BLeave it, since a low point lets any water settle away from the pump
- CReroute and support it so it runs free of traps, bends and restrictions
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Reroute and support it so it runs free of traps, bends and restrictions
A booster pump inspection covers leaks, the condition of the pump's fuel and electrical connections and the wear of its motor brushes, and it calls for making sure the drain lines are free of traps, bends or restrictions. A loop that holds fuel is a trap, so the line is rerouted and supported until it runs clear. Capping it would stop it draining at all, and a drain line is not a water sump.
- Q.04
A pressure carburetor has a fixed bleed from its D chamber to the vapor vent. Checking the vent with the boost pump on, you see an initial spurt of fuel and air, then a continuing small stream. What is your call?
FAA-H-8083-32B, ch. 2, p. 2-17
- AThe vent valve is sticking open, so the carburetor needs repair
- BThe vent valve is sticking closed, so vapor is reaching the jets
- CThat is the normal result for a carburetor with that fixed bleed
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
That is the normal result for a carburetor with that fixed bleed
On this check most pressure carburetors give an initial ejection of fuel and air when the boost pump comes on, then cut off to no more than a steady drip at the vent connection. Installations with a fixed bleed from the D chamber to the vapor vent are different: they should show the initial ejection followed by a continuing small stream of fuel. So the stream here is normal. No flow at all would mean the valve is sticking closed, and a steady flow, more than that small stream, would mean it is sticking open.
- Q.05
You are working an engine's idle mixture toward the right setting, adjusting and checking it several times over. Why might you back the idle speed stop right out of the way and hold the rpm with the throttle meanwhile?
FAA-H-8083-32B, ch. 2, p. 2-30
- ASo the mixture control can travel all the way to idle cutoff on each check
- BSo the stop does not need resetting each time the idle speed picks up
- CSo the throttle plate sits wider open and gives the leaner mixture wanted
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
So the stop does not need resetting each time the idle speed picks up
Each idle mixture change alters how fast the engine idles, and as the mixture comes right the idle speed picks up. Holding the wanted rpm with the throttle, with the idle speed stop backed out, saves resetting the stop after every change. The stop only limits how far the throttle closes; it has nothing to do with mixture control travel. Once the mixture checks out, the stop is reset to the idle rpm given in the maintenance manual.
- Q.06
What job does the economizer, also called the power enrichment system, do in a carburetor?
FAA-H-8083-32B, ch. 2, p. 2-8
- AAdds fuel at high power so the cylinders stay cool
- BLeans the mixture by itself as the airplane climbs
- CSquirts extra fuel when the throttle opens quickly
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Adds fuel at high power so the cylinders stay cool
Near full power the engine needs a richer mixture to keep cylinder temperatures down and stop detonation. The economizer is a valve that stays closed at cruise and opens at high power to add that fuel. It saves fuel because the rest of the range can then run leaner. Leaning for altitude is the mixture control's job, and the quick squirt comes from the accelerating pump.
- Q.07
Checking a fuel selector valve, you find a lot of free play in the control before the valve itself moves. Where do you look for the cause?
FAA-H-8083-32B, ch. 2, p. 2-32
- AThe whole operating mechanism, for worn joints, loose pins and broken drive lugs
- BThe fuel strainer, since sediment in the bowl lets the selector slip
- CThe tank vents, since a blocked vent loads the valve and makes it creep
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
The whole operating mechanism, for worn joints, loose pins and broken drive lugs
Selector valves are turned during inspection to check for free operation, excessive backlash and an accurate pointer. Backlash is free play between the control and the valve, so it comes from wear somewhere in the operating mechanism: check the whole run for worn joints, loose pins and broken drive lugs, and replace any defective part. On a cable-operated selector, the cables, pulleys and pulley bearings get a look too. Sediment and blocked vents upset fuel flow, not the play in the control.
- Q.08
You find a blister on the cover of a fuel hose that runs through a wheel well, out in the weather. Why does the handbook warn against pricking the cover of a hose like this one?
FAA-H-8083-32B, ch. 2, p. 2-32
- AThe pinhole lets fuel vapor seep out and collect in the wheel well
- BWater can get in through the hole and attack the wire braid inside
- CThe cover is vulcanized, so the hole spreads into a split in flight
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Water can get in through the hole and attack the wire braid inside
The usual check on a hose blister is to prick it with a pin and see whether air or fluid comes out. But puncturing the outer cover can let in corrosive elements such as water, which can attack the wire braiding and in the end make the hose fail. That is why puncturing the cover of hoses exposed to the elements should be avoided. The risk the handbook names is corrosion of the braid, not fuel vapor or the cover splitting open.
- Q.09
On a large turbofan with a FADEC, the EEC positions the metering valve that sets fuel flow. What else does it command through its torque motors and solenoids?
FAA-H-8083-32B, ch. 2, p. 2-39
- AThe cabin pressure controller and the air conditioning packs
- BThe airframe fuel tank boost pumps and the crossfeed valves
- CBleed valves, variable stator vanes and turbine case cooling
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Bleed valves, variable stator vanes and turbine case cooling
Besides controlling the metering valve in the fuel metering unit, the EEC runs several other engine subsystems through torque motors and solenoids: the fuel and air oil coolers, bleed valves, variable stator vanes, turbine cooling air valves and the turbine case cooling system. Cabin pressure, the air conditioning packs and the tank pumps and crossfeed belong to the airframe, not to the engine subsystems the EEC runs.
- Q.10
During a fuel system inspection on an airplane with electrical fuel quantity gauges, what do you check at both the flight deck indicator and the tank units?
FAA-H-8083-32B, ch. 2, p. 2-32
- AA drain at each tank unit, to check the fuel there for water
- BSecure mounting of each unit and tight connections at each one
- CA clear sight glass with no leaks at any of its connections
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Secure mounting of each unit and tight connections at each one
Each kind of quantity gauge has its own inspection items. A sight gauge needs clear glass and no leaks at its connections, and a mechanical gauge needs a float arm that moves freely in step with its pointer. On electrical and electronic gauges, both the indicator and the tank units must be securely mounted and their electrical connections tight. Tank units are not drain points, and water is drained at the sumps and strainers.
We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.
How a missed code comes back at the oral
Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.III.I. The examiner reads those codes before your oral and practical.
The Powerplant oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Powerplant also carries 11 practical projects, each with 2 questions attached.
Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.
Questions people ask about engine fuel and fuel metering systems
Q.01What kinds of carburetor ice are there?
There are 3 kinds: fuel evaporation ice, throttle ice and impact ice. Fuel evaporation ice forms because the fuel cools the air as it evaporates, and it can form with carburetor air as warm as 100 degrees F, over a wide range of humidity.
Q.02What does the mixture control do?
It sets the ratio of fuel to air. As the aircraft climbs the air gets less dense, but the carburetor keeps metering about the same fuel, so the mixture naturally gets richer with altitude. The mixture control, manual or automatic, cuts the fuel flow to match.
Q.03What does the accelerating system in a carburetor do?
It supplies extra fuel when the throttle is opened suddenly. The airflow increases faster than the fuel discharge can follow, so without it the mixture would go lean for a moment; with it the engine accelerates smoothly.
Q.04What is FADEC?
Full authority digital engine control. It takes its inputs from electronic sensors and controls the fuel flow through electronic outputs, so the computer has complete control of the engine, and its computing depends entirely on those sensor inputs.
Q.05How many engine fuel and fuel metering systems questions are on the FAA A&P Powerplant test?
The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Engine Fuel and Fuel Metering Systems subject area 5 to 10% of the Powerplant test, which is 5 to 10 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.
Q.06Which FAA handbook chapter covers engine fuel and fuel metering systems?
Chapter 2 of FAA-H-8083-32B, the Aviation Maintenance Technician Handbook: Powerplant, titled "Engine Fuel & Fuel Metering Systems". It runs from pages 2-1 to 2-46, and the FAA publishes the whole handbook free as a PDF.
Read the documents, not us
Every fact on this page was read from these on 19 August 2026 and 15 November 2026. They are the authority and we are the summary. If we and one of them disagree, they are right.
- FAA-H-8083-32B, Aviation Maintenance Technician Handbook: Powerplant, chapter 2www.faa.gov
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standardswww.faa.gov
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards: the written test blueprints (pages 13 and 14) and chapters 6 and 7www.faa.gov
- FAA, Frequently Missed Knowledge Test ACS Codes, 2nd Quarter CY25www.faa.gov
More FAA A&P Powerplant subjects
FREE PLAN · NO CARD · 25 QUESTIONS TO START
The bank holds 340 engine fuel and fuel metering systems questions.
Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.
Start freeOr answer a few first. The free FAA A&P practice test runs on the page, with no account.