PrepAMT Academy

AMP · PP-05 · FAA-H-8083-32B CH. 5

FAA A&P Powerplant: Engine Starting Systems

For the FAA A&P Powerplant test, aircraft engine starting systems is chapter 5 of FAA-H-8083-32B, Engine Starting Systems. Its ACS subject area, Ignition and Starting Systems, is 5 to 10% of the test, or 5 to 10 of its 100 scored questions. Our question bank holds 161 questions on it, and the 10 below were written for this page.

Test shares and most-missed codes read from the FAA on 15 November 2026.

01 WHAT IT COVERSFAA-H-8083-32B · CH. 5

What FAA-H-8083-32B chapter 5 covers

Chapter 5 covers how engines are started, beginning with reciprocating engine starters, from the inertia starters of older engines to the direct cranking electric starters of today, with their switches, solenoids, maintenance and troubleshooting.

It then covers gas turbine engine starters: electric starters and starter generators, and air turbine starters fed by an auxiliary power unit, a ground cart or another engine, with the start sequence and the troubleshooting of each.

It runs from pages 5-1 to 5-16 of the Aviation Maintenance Technician Handbook: Powerplant, which the FAA publishes free as a PDF.

02 SHARE OF THE TESTFAA-G-ACS-1 · BLUEPRINT

How much of the FAA A&P Powerplant test it is

  • 5 to 10%OF THE TESTACS area AM.III.H
  • 5 to 10QUESTIONSof 100 scored
  • 161IN OUR BANKquestions on this subject

The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Ignition and Starting Systems (AM.III.H) is 5 to 10% (5 to 10 questions) on the 100-question Powerplant test. The 13 ranges for the Powerplant test add up to anywhere from 65% to 140%, so they say how big an area can get, not how many questions you will see from it.

Ignition and Starting Systems is not ours alone to cover: our Engine Ignition and Electrical Systems questions are written to the same area.

No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.

03 EXAMPLE QUESTIONSWRITTEN FOR THIS PAGE

Aircraft engine starting systems questions and answers

10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.

  1. Q.01

    The turbine housing of an air turbine starter has a rotor containment ring built into it. What is the ring for?

    FAA-H-8083-32B, ch. 5, p. 5-13

    1. AKeeping the rotor centered in its housing as the parts heat up and grow
    2. BTaking the energy out of blade fragments if the rotor bursts from overspeed
    3. CKeeping the starter air from leaking into the oil in the transmission
    SHOW THE ANSWER

    THE ANSWER IS B.

    Taking the energy out of blade fragments if the rotor bursts from overspeed

    If an air turbine starter's rotor overspeeds badly enough to fail, its blades come apart with a lot of energy. The containment ring in the turbine housing is there to soak up that energy and send the fragments out through the exhaust duct at low energy, rather than through the case. Locating the rotor is the job of its bearings, and the transmission keeps its own oil in a separate housing with its own sump and vent.

  2. Q.02

    A starter generator's shunt field winding is found open, while its other 3 field windings test good. Which of its 2 jobs could it still do?

    FAA-H-8083-32B, ch. 5, p. 5-10

    1. ANo job at all, since all 4 windings work in both of its jobs
    2. BGenerating only, since cranking takes every field winding it has at once
    3. CCranking the engine, though not generating once it is running
    SHOW THE ANSWER

    THE ANSWER IS C.

    Cranking the engine, though not generating once it is running

    A starter generator cranks on its C field, compensating winding and commutating winding, all in series with the source, and makes no practical use of its shunt field while starting. As a generator it uses the shunt, compensating and commutating windings, with the shunt field in the voltage control circuit and the C field used only for starting. So an open shunt field leaves cranking alone but stops it working as a generator; cranking never needed all 4 windings.

  3. Q.03

    On an air turbine starter, oil goes into the transmission sump through a port closed by a vent plug with a ball valve in it. What does that ball valve allow?

    FAA-H-8083-32B, ch. 5, p. 5-13

    1. AThe sump to breathe to the atmosphere during normal flight
    2. BOil to drain from the sump once the starter is off the engine
    3. COutside air in only on the ground, the sump sealed in flight
    SHOW THE ANSWER

    THE ANSWER IS A.

    The sump to breathe to the atmosphere during normal flight

    The vent plug closes the fill port, and the ball valve in it lets the transmission sump vent to the outside air in normal flight. Oil comes out through the magnetic drain plug in the transmission drain opening, which also catches any ferrous particles, and the oil level is checked at the sight gauge on the housing. The starter's oil is the same kind of turbine oil the engine uses, but it never circulates through the engine.

  4. Q.04

    Before an air turbine start, the ramp crew has a ground air cart hooked up while the APU is also running and able to feed the starter duct. What does the handbook say about using these 2 air sources?

    FAA-H-8083-32B, ch. 5, p. 5-12

    1. AThe cart and the APU feed the duct together for enough air
    2. BOnly one of them is used at a time to start the engine
    3. CThe APU must be shut down, since it cannot feed a start
    SHOW THE ANSWER

    THE ANSWER IS B.

    Only one of them is used at a time to start the engine

    Air for an air turbine starter can come from a ground cart, the APU or a cross-bleed from an engine that is already running, and the handbook has the engines started from just one of those sources at a time, at around 30 to 50 psi. So the APU is a proper source, not one that has to be shut down, and the cart and the APU are not run into the duct together. Whichever one is used, the duct pressure is checked before the start attempt.

  5. Q.05

    On a starter generator system with an undercurrent controller, the undercurrent relay's contacts are burned so badly that they no longer close the circuit. You hold the start switch on, the starter cranks, and then you let the switch go. What happens?

    FAA-H-8083-32B, ch. 5, p. 5-11

    1. ACranking carries on until the current falls below about 200 amps
    2. BCranking carries on until the stop switch is pressed
    3. CThe start relays drop out and cranking stops
    SHOW THE ANSWER

    THE ANSWER IS C.

    The start relays drop out and cranking stops

    Pressing the start switch closes the motor, ignition and battery cutout relays. In a working system the heavy motor current then flows through the undercurrent relay's coil and closes it, and its contacts feed the 3 relay coils from the positive bus, which is why the start switch can be released. With those contacts burned open, that holding circuit is never made, so letting go of the start switch removes the only supply to the 3 coils and the start ends there. The 200 amp dropout and the stop switch only matter once the undercurrent relay is holding.

  6. Q.06

    At the moment the starter switch is turned on for an air turbine start, why can the bellows in the pressure-regulating valve's control be fully extended by its spring?

    FAA-H-8083-32B, ch. 5, p. 5-15

    1. AA sealed nitrogen charge inside it pushes it out to its full length
    2. BThe valve is still shut, so there is almost no downstream pressure
    3. CIts sensing line stays shut off until the start valve opens
    SHOW THE ANSWER

    THE ANSWER IS B.

    The valve is still shut, so there is almost no downstream pressure

    The bellows is connected by an air line to the pressure-sensing port on the starter, so it feels the regulated pressure downstream of the valve. When the switch is first turned on, the butterfly is still closed, so there is almost no downstream pressure and the bellows spring holds the bellows fully extended. It is that spring, not a gas charge, that pushes it out, and no valve closes off the sensing line. As the valve opens, the downstream pressure bled back through the sensing line compresses the bellows and moves the control rod, and the system settles at its regulated value.

  7. Q.07

    A turboprop with an air turbine starter has to be started away from base. The APU is out of service, there is no ground cart, and no other engine is running. What can, in some limited cases, still supply the starting air?

    FAA-H-8083-30B, ch. 1, p. 1-14

    1. AA low-pressure, large-volume air tank
    2. BThe aircraft's fire extinguisher bottles, discharged into the duct
    3. CRam air forced through the inlet while it is towed
    SHOW THE ANSWER

    THE ANSWER IS A.

    A low-pressure, large-volume air tank

    Air for an air turbine starter normally comes from the APU, a ground air cart, or a cross-bleed from an engine that is already running. In some limited cases, a low-pressure tank that holds a large volume of air can also supply it. Fire extinguisher bottles hold agent for putting out fires, not air for a start, and towing an airplane forces nowhere near enough air through the engine to turn it up to starting speed.

  8. Q.08

    A small airplane's starter drives a ring gear on the propeller hub, and you find the starter drive gear teeth badly worn. Besides replacing the drive gear, what do you check?

    FAA-H-8083-32B, ch. 5, p. 5-7

    1. AThe magneto timing, since a worn drive gear throws it off
    2. BThe starter brushes, since they are what wears the gear teeth
    3. CThe ring gear on the hub, and the starter's mounting and wiring
    SHOW THE ANSWER

    THE ANSWER IS C.

    The ring gear on the hub, and the starter's mounting and wiring

    A worn drive gear has been running against the ring gear, so the ring gear on the propeller hub plate is checked for wear at the same time. The routine starter check also covers the electrical connections, for looseness and corrosion, and the security of the starter housing's mounting. Gear wear has nothing to do with magneto timing, and brushes wear against the commutator, not the gear teeth.

  9. Q.09

    A large piston engine will not start. You crank for 1 minute, rest the starter, then crank for another 1 minute and it still has not fired. Keeping to the usual starter limits, how many minutes after the first crank began can a third crank start?

    FAA-H-8083-32B, ch. 5, p. 5-6

    1. A8 minutes
    2. B4 minutes
    3. C7 minutes
    SHOW THE ANSWER

    THE ANSWER IS A.

    8 minutes

    Starter limits keep the motor from overheating. After the first 1 minute of cranking it rests at least 1 minute, and after a second 1 minute of cranking it rests 5 minutes. So 1 + 1 + 1 + 5 is 8 minutes from the start of the first crank. Giving it only 1 minute of rest both times comes to 4, which risks burning out the starter.

  10. Q.10

    In the gear section of a large direct cranking starter, what keeps the proper pressure on the clutch pack of steel and bronze plates?

    FAA-H-8083-32B, ch. 5, p. 5-4

    1. AOil pressure fed into the gear section from the engine
    2. BA clutch spring retainer assembly
    3. CA magnetic clamp energized along with the motor field
    SHOW THE ANSWER

    THE ANSWER IS B.

    A clutch spring retainer assembly

    The planet gears engage the internal teeth of the steel clutch plates, which are interleaved with bronze plates splined to the housing so they cannot turn, and a clutch spring retainer assembly keeps the proper pressure on the whole pack. The pressure is mechanical: no engine oil is fed into the starter's gear section for it, and nothing magnetic clamps the plates together.

We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.

04 AND THEN THE ORAL§ 65.79

How a missed code comes back at the oral

Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.III.H. The examiner reads those codes before your oral and practical.

The Powerplant oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Powerplant also carries 11 practical projects, each with 2 questions attached.

Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.

05 COMMON QUESTIONSFAQ

Questions people ask about aircraft engine starting systems

Q.01

What is a starter generator?

An electric motor and a generator in the same housing. It cranks a turbine engine as a motor, then switches to work as a generator once the engine reaches self-sustaining speed, which saves weight and space on the engine.

Q.02

Where does an air turbine starter get its air?

From a ground air cart, the auxiliary power unit, or a cross-bleed from another engine that is already running. The air drives a turbine wheel connected through reduction gears to one of the engine’s compressors, usually the highest pressure one, and a clutch lets go once the engine is running.

Q.03

What is an inertia starter?

A starter that stores kinetic energy in a rapidly turning flywheel, spun up by hand, by an electric motor, or by either, and then uses that energy to crank the engine. Few aircraft still have them.

Q.04

Why does an electric starter have a time limit?

Because of the high energy it uses cranking the engine. Starter limits have to be kept or the starter overheats. A typical limit: after 1 minute of cranking, let it cool for at least 1 minute, and after a second or later 1 minute period, let it cool for 5 minutes.

Q.05

How many aircraft engine starting systems questions are on the FAA A&P Powerplant test?

The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Ignition and Starting Systems subject area 5 to 10% of the Powerplant test, which is 5 to 10 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.

Q.06

Which FAA handbook chapter covers aircraft engine starting systems?

Chapter 5 of FAA-H-8083-32B, the Aviation Maintenance Technician Handbook: Powerplant, titled "Engine Starting Systems". It runs from pages 5-1 to 5-16, and the FAA publishes the whole handbook free as a PDF.

FREE PLAN · NO CARD · 25 QUESTIONS TO START

The bank holds 161 aircraft engine starting systems questions.

Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.

Start free

Or answer a few first. The free FAA A&P practice test runs on the page, with no account.