AMP · PP-04 · FAA-H-8083-32B CH. 4
FAA A&P Powerplant: Engine Ignition and Electrical Systems
For the FAA A&P Powerplant test, engine ignition and electrical systems is chapter 4 of FAA-H-8083-32B, Engine Ignition & Electrical Systems. Its main ACS subject area, Ignition and Starting Systems, is 5 to 10% of the test, or 5 to 10 of its 100 scored questions. Our question bank holds 533 questions on it, and the 10 below were written for this page.
Test shares and most-missed codes read from the FAA on 15 November 2026.
What FAA-H-8083-32B chapter 4 covers
Chapter 4 covers reciprocating engine ignition: the magneto and its magnetic, primary and secondary circuits, magneto timing and the E-gap, high and low tension systems, harnesses, spark plugs and how to inspect and service them, and impulse couplings and the other aids to starting. It also covers turbine engine ignition.
The engine electrical half covers choosing and installing wire, connectors and conduit on the engine, and the DC generators driven by it, with their voltage control and maintenance.
It runs from pages 4-1 to 4-71 of the Aviation Maintenance Technician Handbook: Powerplant, which the FAA publishes free as a PDF.
How much of the FAA A&P Powerplant test it is
- 5 to 10%OF THE TESTACS area AM.III.H
- 5 to 10QUESTIONSof 100 scored
- 533IN OUR BANKquestions on this subject
The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Ignition and Starting Systems (AM.III.H) is 5 to 10% (5 to 10 questions) on the 100-question Powerplant test. Our Engine Ignition and Electrical Systems questions also reach into Engine Electrical Systems (AM.III.F, 5 to 15%). The 13 ranges for the Powerplant test add up to anywhere from 65% to 140%, so they say how big an area can get, not how many questions you will see from it.
Ignition and Starting Systems is not ours alone to cover: our Engine Starting Systems questions are written to the same area.
No code in these areas is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.
Engine ignition and electrical systems questions and answers
10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.
- Q.01
Each type of aircraft cable carries only the minimum insulation its particular job needs. Why is more insulation not simply added for safety?
FAA-H-8083-32B, ch. 4, p. 4-52
- AInsulation costs money and stiffens the cable, and cables work in widely varied conditions
- BThicker insulation traps moisture against the conductor, which then corrodes
- CExtra layers of insulation lower the cable's dielectric strength
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Insulation costs money and stiffens the cable, and cables work in widely varied conditions
Insulation is expensive and it stiffens the cable, and conductors are used under a great variety of physical and electrical conditions. For those reasons only the necessary minimum insulation is put on any type of cable made for a specific job. More insulation would not lower its dielectric strength, which is its ability to withstand a voltage difference without breaking down.
- Q.02
An engine idles rough, so its spark plugs are changed. It runs smoothly for a few hours, then the same roughness comes back. What does that point to?
FAA-H-8083-32B, ch. 4, p. 4-26
- AThe new plugs were faulty too, so a third set should be tried
- BA fault in some other system that the plug change only covered up for a while
- CNormal running-in, since new plugs take a few hours to settle their gaps
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
A fault in some other system that the plug change only covered up for a while
Spark plugs are often blamed when the real fault lies in another system. Carburetor faults, poor fuel distribution, too much valve overlap, a leaking primer or poor idle speed and mixture settings give the same symptoms as faulty ignition. A plug change can improve many of these for a while, but the trouble soon comes back because the real cause is still there. New plugs do not need hours to settle, and a third set would only hide the fault again.
- Q.03
During a magneto inspection the felt oiler pad checks out fine, but you find an oily, gummy film on the sides of the breaker contacts. How do you clean it off?
FAA-H-8083-32B, ch. 4, p. 4-39
- ADress the contacts with a fine file until bright metal shows all round
- BSpray the breaker compartment with engine cleaning solvent and blow it dry
- CSwab the contacts with a pipe cleaner or similar wiper dipped in acetone
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Swab the contacts with a pipe cleaner or similar wiper dipped in acetone
An oily or gummy substance on the sides of the contacts is swabbed off with a flexible wiper, such as a pipe cleaner dipped in acetone or another approved solvent, and a hook formed on its end reaches the back of the contacts. Engine cleaning solvents are kept out of the breaker compartment, since they hold dirt and grime that foul good contacts, and filing is for the surface condition of the contacts, not for an oily film on their sides.
- Q.04
You have just seated a set of generator brushes with 000 sandpaper and cleaned out the carbon dust. What do you check once the generator has run for a short time?
FAA-H-8083-32B, ch. 4, p. 4-14
- AThat no pieces of sand have become embedded in the brushes
- BThat the brush springs can now be backed off to their running tension
- CThat the leftover carbon dust has packed in between the commutator bars
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
That no pieces of sand have become embedded in the brushes
Seating brushes with extra-fine 000 sandpaper leaves carbon dust, which has to be cleaned out of every part of the generator straight afterward, not left to pack in anywhere. Then, after the generator has run for a short period, the brushes are inspected to make sure no pieces of sand have become embedded in them, where they would collect copper from the commutator. Brush spring pressure is not backed off after seating: it stays at what the manufacturer recommends.
- Q.05
An engine is certificated to use either a hot or a cold spark plug. What decides which of the 2 a particular installation uses?
FAA-H-8083-32B, ch. 4, p. 4-25
- AThe magneto fitted, since a high-tension system calls for the colder plug
- BIts compression ratio, its degree of supercharging and how it is operated
- CThe climate it is based in, with colder plugs for hot summer flying
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Its compression ratio, its degree of supercharging and how it is operated
Heat range is a plug's ability to pass combustion heat to the cylinder head, and the engine maker picks the plugs after testing. Where an engine is approved for both, the choice follows its compression ratio, how much it is supercharged and the way it will be operated: high-compression engines tend to use colder plugs, low-compression engines hotter ones. Neither the type of magneto nor the local climate sets it.
- Q.06
A box of new spark plugs shows a film of rust-preventive compound on the core insulators and inside the shielding barrels. What do you do before fitting them?
FAA-H-8083-32B, ch. 4, p. 4-37
- AWash it off with a brush and solvent, then dry them with a dry air blast
- BFit them as they are, since the compound burns off in the first run
- CWipe the barrels with antiseize so the compound cannot reach the contact
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Wash it off with a brush and solvent, then dry them with a dry air blast
New and reconditioned plugs are checked before they go in, and one check is for rust-preventive compound on the outside, on the core insulator and inside the shielding barrel. Any that has built up is washed off with a brush and cleaning solvent, and the plug is then dried with a dry air blast. Left inside the barrel it is foreign material in the contact area. Antiseize has no place there: its graphite conducts, and it goes only on the shell threads, kept clear of the electrodes.
- Q.07
You need to clean a spark plug bushing's threads with a cleanout tap, but the plug hole sits deeper than you can reach with your hand around the tap. How do you start it?
FAA-H-8083-32B, ch. 4, p. 4-37
- AStart it with a ratchet and socket, since a deep hole cannot cross-thread
- BUse a tap one size larger, which reaches farther into the bushing
- CSlip a short length of hose over the tap's square end as an extension
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Slip a short length of hose over the tap's square end as an extension
The tap is started by hand until there is no chance of it cross-threading in the bushing. Where the plug hole is deeper than a clenched hand can reach, a short length of hose slipped over the square end of the tap acts as an extension so it can still be started that way. The tap is then run in until its full cutting thread reaches the bottom thread of the bushing. A larger tap would cut into the bushing's own metal instead of just clearing the carbon.
- Q.08
After a start, one cylinder does not fire at first. As rpm rises it begins firing on and off, white fumes come from the exhaust for a few seconds, and then the engine runs clean. What was going on?
FAA-H-8083-32B, ch. 4, p. 4-34
- AAn impulse coupling that only engaged once the rpm had risen
- BAn oil-wet plug, cleared as airflow and combustion carried the oil away
- CA carbon track in the distributor that burned off as it warmed
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
An oil-wet plug, cleared as airflow and combustion carried the oil away
Oil that has been in service holds fine carbon particles that conduct, so a plug full of oil passes the high voltage through the oil without a spark, and that cylinder does not fire. As rpm rises, the extra airflow carries the excess oil away, intermittent firing starts, and combustion clears the rest, so within a few seconds the engine runs clean with white fumes of burning oil in the exhaust. A carbon track stays until it is cleaned, and an impulse coupling works only at cranking speed.
- Q.09
A DC generator is geared to turn 1.25 times crankshaft speed and comes in at 1,500 generator rpm. At what engine rpm does it start producing its normal voltage?
FAA-H-8083-32B, ch. 4, p. 4-13
- A1,875 rpm
- B1,500 rpm
- C1,200 rpm
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
1,200 rpm
The generator turns 1.25 times as fast as the crankshaft, so the engine only has to reach the coming-in speed divided by 1.25. 1,500 divided by 1.25 is 1,200 engine rpm. Multiplying instead gives 1,875, which is the generator speed at 1,500 engine rpm, and 1,500 forgets the gearing altogether.
- Q.10
When is moisture inside a reciprocating engine's ignition system most likely to cause trouble?
FAA-H-8083-32B, ch. 4, p. 4-26
- AIn cruise at altitude, when the outside air is at its coldest
- BDuring a long climb at high power, while the harness is flexing
- CDuring starting and ground operation, before the system is hot
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
During starting and ground operation, before the system is hot
Moisture building up in flight is extremely rare, because the high operating temperature of the system keeps condensation from forming. Engine heat normally evaporates any moisture, but moist air can sometimes condense as the engine cools, so the trouble shows mostly during starting and ground operation. In cruise and in a long climb the system is at its full operating temperature.
We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.
How a missed code comes back at the oral
Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.III.H or AM.III.F. The examiner reads those codes before your oral and practical.
The Powerplant oral runs from 4 questions if your written was clean up to 34, because every code you missed adds 1 more. Powerplant also carries 11 practical projects, each with 2 questions attached.
Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.
Questions people ask about engine ignition and electrical systems
Q.01What does an impulse coupling do?
At cranking speed it holds the magneto’s rotating magnet back with a flyweight while the engine turns, then releases it near top dead center, and the spring gives the magnet a quick twist. That makes an intense spark for starting and retards it, so the piston does not kick back.
Q.02What is the E-gap in a magneto?
The position of the rotating magnet a few degrees past its neutral position, where the breaker points open. E stands for efficiency: opening the primary circuit there gives the strongest spark, and the magneto must be in the E-gap position to fire a plug.
Q.03Why are turbine engine ignition systems dangerous to work on?
Most gas turbine engines use high energy capacitor discharge ignition, and the energy and voltage it carries can injure or kill anyone who comes into contact with the system while it is activated. Before any part of it is handled, the system is switched off and its stored charge is given at least 1 minute to drain, and the manufacturer’s precautions are followed.
Q.04What is the P-lead on a magneto?
The P-lead is the magneto ground lead. Turning the ignition switch off grounds the magneto through it so it cannot fire. If the engine keeps firing with the switch off, the P-lead is open, the magneto is still live, and turning the propeller by hand can kill.
Q.05How many engine ignition and electrical systems questions are on the FAA A&P Powerplant test?
The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Ignition and Starting Systems subject area 5 to 10% of the Powerplant test, which is 5 to 10 of the 100 scored questions. That is a range, not a quota, so your own test can land anywhere inside it. Our Engine Ignition and Electrical Systems questions also reach into Engine Electrical Systems (5 to 15%).
Q.06Which FAA handbook chapter covers engine ignition and electrical systems?
Chapter 4 of FAA-H-8083-32B, the Aviation Maintenance Technician Handbook: Powerplant, titled "Engine Ignition & Electrical Systems". It runs from pages 4-1 to 4-71, and the FAA publishes the whole handbook free as a PDF.
Read the documents, not us
Every fact on this page was read from these on 19 August 2026 and 15 November 2026. They are the authority and we are the summary. If we and one of them disagree, they are right.
- FAA-H-8083-32B, Aviation Maintenance Technician Handbook: Powerplant, chapter 4www.faa.gov
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standardswww.faa.gov
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards: the written test blueprints (pages 13 and 14) and chapters 6 and 7www.faa.gov
- FAA, Frequently Missed Knowledge Test ACS Codes, 2nd Quarter CY25www.faa.gov
More FAA A&P Powerplant subjects
FREE PLAN · NO CARD · 25 QUESTIONS TO START
The bank holds 533 engine ignition and electrical systems questions.
Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.
Start freeOr answer a few first. The free FAA A&P practice test runs on the page, with no account.