PrepAMT Academy

AMG · GEN-11 · FAA-H-8083-30B CH. 11

FAA A&P General: Hand Tools and Measuring Devices

For the FAA A&P General test, aircraft hand tools and measuring devices is chapter 11 of FAA-H-8083-30B, Hand Tools & Measuring Devices. Its main ACS subject area, Aircraft Materials, Hardware, and Processes, is 5 to 10% of the test, or 3 to 6 of its 60 scored questions. Our question bank holds 221 questions on it, and the 10 below were written for this page.

Test shares and most-missed codes read from the FAA on 15 November 2026.

01 WHAT IT COVERSFAA-H-8083-30B · CH. 11

What FAA-H-8083-30B chapter 11 covers

Chapter 11 covers the general purpose tools: hammers and mallets, screwdrivers, pliers, punches, the many kinds of wrench, and the torque wrench. It then covers the metal cutting tools, hand snips, hacksaws, chisels, files, drills and drill bits, reamers and countersinks, and the taps and dies that cut threads.

The measuring half covers layout and measuring tools, from rules, combination sets, scribers and dividers to calipers, then the precision instruments: the micrometer and how to read it, the vernier scale, and the dial indicator.

It runs from pages 11-1 to 11-26 of the Aviation Maintenance Technician Handbook: General, which the FAA publishes free as a PDF.

02 SHARE OF THE TESTFAA-G-ACS-1 · BLUEPRINT

How much of the FAA A&P General test it is

  • 5 to 10%OF THE TESTACS area AM.I.E
  • 3 to 6QUESTIONSof 60 scored
  • 221IN OUR BANKquestions on this subject

The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Aircraft Materials, Hardware, and Processes (AM.I.E) is 5 to 10% (3 to 6 questions) on the 60-question General test. Our Hand Tools and Measuring Devices questions also reach into Inspection Concepts and Techniques (AM.I.K, 5 to 10%). The 12 ranges for the General test add up to anywhere from 60% to 130%, so they say how big an area can get, not how many questions you will see from it.

Aircraft Materials, Hardware, and Processes is not ours alone to cover: our Aircraft Materials, Hardware and Processes questions are written to the same area.

No code in these areas is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.

03 EXAMPLE QUESTIONSWRITTEN FOR THIS PAGE

Aircraft hand tools and measuring devices questions and answers

10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.

  1. Q.01

    Why should a screwdriver never be used to check whether an electric circuit is live?

    FAA-H-8083-30B, ch. 11, p. 11-2

    1. AThe arc can burn the tip, or even weld the blade to the part and short it
    2. BThe steel shank reads the voltage wrong and gives a false result
    3. CThe handle insulation melts at once at normal aircraft voltages
    SHOW THE ANSWER

    THE ANSWER IS A.

    The arc can burn the tip, or even weld the blade to the part and short it

    Touching a screwdriver across a live circuit draws an electric arc. The arc burns the tip so it no longer fits screws properly, and it can even fuse the blade to the part being checked, which leaves a short circuit. A screwdriver is not a measuring tool, so it has no reading to get wrong, and the trouble is at the tip, not in the handle. A meter or test light made for the job is the right tool.

  2. Q.02

    Why are roundnose pliers not made for heavy work?

    FAA-H-8083-30B, ch. 11, p. 11-3

    1. ATheir jaws are too short to reach into a deep crimp
    2. BToo much pressure springs their jaws out of shape
    3. CTheir steel is too soft to hold a cutting edge
    SHOW THE ANSWER

    THE ANSWER IS B.

    Too much pressure springs their jaws out of shape

    Roundnose pliers are for crimping and forming light metal. They are not made for heavy work, because too much pressure springs the jaws, which are often wrapped to keep them from scarring the metal. Short jaws or soft steel are not the reason they are kept to light work.

  3. Q.03

    You need to drive a center punch to mark a hole before drilling. Which hammer should you use?

    FAA-H-8083-30B, ch. 11, p. 11-1

    1. AA soft-faced hammer, so the punch head is not marred
    2. BA rawhide mallet, so the metal around the mark is not dented
    3. CA metal-headed hammer, with safety glasses on
    SHOW THE ANSWER

    THE ANSWER IS C.

    A metal-headed hammer, with safety glasses on

    A soft-faced hammer, with a face of wood, brass, lead, rawhide, hard rubber or plastic, is for forming soft metal and striking surfaces that mark easily, and a mallet is for shaping thin metal without creases. Soft faces are not used on punch heads, bolts or nails, because that quickly ruins them. A punch is struck with a metal-headed hammer, and since that is metal striking a metal tool, safety glasses or goggles are strongly encouraged.

  4. Q.04

    You are about to start a hacksaw cut across a bar that has a sharp, square corner where the blade will go in. What should you do first?

    FAA-H-8083-30B, ch. 11, p. 11-8

    1. AStart with heavy pressure so the teeth bite straight in
    2. BStart the cut on the back stroke so the teeth cannot catch
    3. CNick the starting point with the edge of a file
    SHOW THE ANSWER

    THE ANSWER IS C.

    Nick the starting point with the edge of a file

    Nicking the starting point with the edge of a file breaks the sharp corner, which could otherwise strip the teeth, and it also helps start the saw in the right place. The cut is then started with a light, steady forward stroke, keeping at least 2 teeth on the work. A hacksaw cuts only on the forward stroke, so starting on the back stroke does nothing, and heavy pressure at the start is just what strips teeth.

  5. Q.05

    A round nut on a fitting has a ring of notches in its rim, and you have a hook spanner to loosen it. How should the spanner go on?

    FAA-H-8083-30B, ch. 11, p. 11-5

    1. AHook in a notch, with the handle pointing the way the nut is to turn
    2. BHook in a notch, with the handle pointing against the way the nut turns
    3. CHook across 2 notches at once, so the load is shared between them
    SHOW THE ANSWER

    THE ANSWER IS A.

    Hook in a notch, with the handle pointing the way the nut is to turn

    A hook spanner has a curved arm with a hook on the end. The hook goes into one of the notches with the handle pointing in the direction the nut is to be turned, so the pull keeps the hook seated. Set the other way, the pull drags the hook out of the notch. A single hook fits only one notch: spanners with 2 lugs are the U-shaped kind used on notches cut in the face of a nut.

  6. Q.06

    The cordless power screwdriver is flat, so a coworker suggests taking a row of panel screws out with a cordless drill and a screwdriver bit. Why is that a poor idea?

    FAA-H-8083-30B, ch. 11, p. 11-2

    1. AA drill turns too slowly to break tight screws loose
    2. BA drill has no slip clutch, so it can chew up the screw heads
    3. CA drill chuck cannot hold a crosspoint screwdriver bit
    SHOW THE ANSWER

    THE ANSWER IS B.

    A drill has no slip clutch, so it can chew up the screw heads

    Cordless drills fitted with a screwdriver tip are not recommended for taking out or putting in screws, because a drill has no slip clutch, and the tip can damage the slot or recess in the screw head. A power screwdriver has a clutch for that reason, and even then a setting that is too high lets the tip spin on the head. Speed and the chuck are not the problem: the missing clutch is.

  7. Q.07

    You have just broken a tight nut loose with a box-end wrench, and there is not room to swing the wrench in a full circle. What is the quicker way to run the nut off?

    FAA-H-8083-30B, ch. 11, p. 11-4

    1. AFinish it with an open-end wrench, such as the open end of a combination wrench
    2. BKeep using the box end, since it turns a nut faster once the nut is loose
    3. CLoosen it the rest of the way with a torque wrench set to its lowest value
    SHOW THE ANSWER

    THE ANSWER IS A.

    Finish it with an open-end wrench, such as the open end of a combination wrench

    A box-end wrench is ideal for breaking a tight nut loose, but unless it can turn in a complete circle it has to be lifted off and set back on for every short swing, which wastes time. Once the nut is loose it comes off more quickly with an open-end wrench, which is why a combination wrench, with a box at one end and an open end at the other, suits the job.

  8. Q.08

    While filing a soft aluminum part, you notice the file is now leaving deep scratches in it. What is the likely cause, and what is the fix?

    FAA-H-8083-30B, ch. 11, p. 11-12

    1. AThe file is too fine, so change to a bastard cut file
    2. BMetal particles are packed in the teeth, so clean them out with a file card
    3. CToo little pressure on the return stroke, so bear down both ways
    SHOW THE ANSWER

    THE ANSWER IS B.

    Metal particles are packed in the teeth, so clean them out with a file card

    Particles of metal collect between a file's teeth and can make deep scratches in the work. Tapping the file on the bench every few strokes clears loose filings, and when particles are lodged too firmly for that, a file card or wire brush drawn down the gullets between the teeth takes them out. A coarser file would cut deeper, not shallower, and pressure is relieved on the return stroke to save the file, never added.

  9. Q.09

    You are about to hacksaw through a length of angle stock held in a bench vise. How should it be clamped?

    FAA-H-8083-30B, ch. 11, p. 11-8

    1. AWith as little of it in the jaws as possible, so the blade has room to move freely
    2. BLoosely, so the stock can turn and follow the blade as it cuts
    3. CWith the most bearing surface, set so the cut engages as many teeth as it can
    SHOW THE ANSWER

    THE ANSWER IS C.

    With the most bearing surface, set so the cut engages as many teeth as it can

    For hacksawing, clamp the work so it has as much bearing surface in the vise as possible and so the cut engages the greatest number of teeth. Firm, broad support keeps the work from shifting or chattering, and with more teeth in the cut each one carries less of the load. Stock held lightly or left loose to turn will chatter and can break the blade.

  10. Q.10

    The face of your ball peen hammer has a small chip and a gouge in it. What will that do when you use it on sheet metal?

    FAA-H-8083-30B, ch. 11, p. 11-1

    1. ANothing, since the weight of the hammer is what does the work
    2. BIt will mar the surface of the work wherever the face strikes
    3. CIt will make the hammer glance off, so it must be held at an angle
    SHOW THE ANSWER

    THE ANSWER IS B.

    It will mar the surface of the work wherever the face strikes

    Hammer and mallet faces must be kept smooth and free from dents, chips and gouges, because a flaw in the face is printed into the work at every blow. Strike the work squarely with the full face, and wear safety glasses when a metal hammer strikes a metal tool. Tilting the hammer to dodge the flaw would break the rule of striking squarely with the full face.

We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.

04 AND THEN THE ORAL§ 65.79

How a missed code comes back at the oral

Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.I.E or AM.I.K. The examiner reads those codes before your oral and practical.

The General oral runs from 4 questions if your written was clean up to 22, because every code you missed adds 1 more. General also carries 9 practical projects, each with 2 questions attached.

Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.

05 COMMON QUESTIONSFAQ

Questions people ask about aircraft hand tools and measuring devices

Q.01

How do you read a micrometer?

Each numbered line on the barrel is a tenth of an inch, 0.100, and each small line between them is 0.025 inch. Each line on the thimble is 0.001 inch. Add the last numbered barrel line showing, 0.025 for each small line showing past it, and the thimble line that meets the barrel’s index line, and that sum is the measurement.

Q.02

What is the difference between a reamer and a drill?

A drill makes the hole. A reamer smooths and enlarges an existing hole to an exact size. Its blades are hardened until they are brittle, so it is handled with care to avoid chipping them, and a hand reamer is turned with a tap wrench or a similar handle.

Q.03

What are taps and dies used for?

Cutting threads. A tap cuts internal threads inside a hole, and a die cuts external threads on a rod or bolt. The hole for a tap is drilled first with the tap drill size for that thread.

Q.04

What is a dial indicator used for?

Measuring small amounts of movement or variation, such as the runout of a shaft or the out of round of a part. The plunger rides on the surface and the dial shows how far it moves, usually in thousandths of an inch.

Q.05

How many aircraft hand tools and measuring devices questions are on the FAA A&P General test?

The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Aircraft Materials, Hardware, and Processes subject area 5 to 10% of the General test, which is 3 to 6 of the 60 scored questions. That is a range, not a quota, so your own test can land anywhere inside it. Our Hand Tools and Measuring Devices questions also reach into Inspection Concepts and Techniques (5 to 10%).

Q.06

Which FAA handbook chapter covers aircraft hand tools and measuring devices?

Chapter 11 of FAA-H-8083-30B, the Aviation Maintenance Technician Handbook: General, titled "Hand Tools & Measuring Devices". It runs from pages 11-1 to 11-26, and the FAA publishes the whole handbook free as a PDF.

FREE PLAN · NO CARD · 25 QUESTIONS TO START

The bank holds 221 aircraft hand tools and measuring devices questions.

Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.

Start free

Or answer a few first. The free FAA A&P practice test runs on the page, with no account.