AMG · GEN-07 · FAA-H-8083-30B CH. 7
FAA A&P General: Aircraft Materials, Hardware and Processes
For the FAA A&P General test, aircraft materials, hardware and processes is chapter 7 of FAA-H-8083-30B, Aircraft Materials, Hardware, & Processes. Its ACS subject area, Aircraft Materials, Hardware, and Processes, is 5 to 10% of the test, or 3 to 6 of its 60 scored questions. Our question bank holds 429 questions on it, and the 10 below were written for this page.
Test shares and most-missed codes read from the FAA on 15 November 2026.
What FAA-H-8083-30B chapter 7 covers
Chapter 7 is the materials aircraft are built from and how they behave: the properties of metals, from hardness and strength to ductility and toughness; ferrous metals and steel; the aluminum, magnesium, titanium and copper alloys; how metals are worked and heat treated; and hardness testing with the Brinell, Rockwell and Barcol testers. It also covers nonmetallic materials such as plastics, rubber and seals.
The hardware half covers the fasteners a mechanic handles every day: bolts and how to identify them, nuts, washers, screws, rivets and special fasteners, nut plates, hole repair hardware, and the safetying methods (safety wire, cotter pins and safety clips) that keep them in place.
It runs from pages 7-1 to 7-80 of the Aviation Maintenance Technician Handbook: General, which the FAA publishes free as a PDF.
How much of the FAA A&P General test it is
- 5 to 10%OF THE TESTACS area AM.I.E
- 3 to 6QUESTIONSof 60 scored
- 429IN OUR BANKquestions on this subject
The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Aircraft Materials, Hardware, and Processes (AM.I.E) is 5 to 10% (3 to 6 questions) on the 60-question General test. The 12 ranges for the General test add up to anywhere from 60% to 130%, so they say how big an area can get, not how many questions you will see from it.
Aircraft Materials, Hardware, and Processes is not ours alone to cover: our Hand Tools and Measuring Devices questions are written to the same area.
No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.
Aircraft materials, hardware and processes questions and answers
10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.
- Q.01
A bar of unknown metal looks like stainless steel. Apart from a spark test, what quick check can show that it is titanium?
FAA-H-8083-30B, ch. 7, p. 7-9
- AWet it and draw it across glass; it leaves a dark, pencil-like line
- BHold a magnet to it; titanium is pulled hard toward the magnet
- CFile a corner; titanium shows a copper color under the surface
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Wet it and draw it across glass; it leaves a dark, pencil-like line
Titanium looks a lot like stainless steel. Besides the spark test, with its brilliant white trace ending in a white burst, wetting the titanium and drawing a line with it on a piece of glass identifies it, since it leaves a dark line like a pencil mark. Titanium is not strongly magnetic, and filing it shows no copper color.
- Q.02
An AN bolt's part number has no letters between its diameter and length numbers, as in AN5-12A. What is the bolt made of?
FAA-H-8083-30B, ch. 7, p. 7-39
- ACorrosion-resistant steel
- BCadmium-plated steel
- C2024 aluminum alloy
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Cadmium-plated steel
In an AN bolt number, letters after the diameter number give the material: C means corrosion-resistant steel and DD means 2024 aluminum alloy. With no letters there, as in AN5-12A, the bolt is cadmium-plated steel. So a bolt called out with a C or DD cannot be swapped for one without, or the other way round, just because the size numbers match.
- Q.03
A fitting is held by an internal wrenching bolt that has to be replaced, and stores has only a standard AN hex head bolt of the same diameter and length. What do you do?
FAA-H-8083-30B, ch. 7, p. 7-38
- AFit the AN hex bolt with a plain washer, since the size is what matters
- BFit the AN hex bolt, but torque it to the value listed for the internal wrenching bolt
- CWait for another internal wrenching bolt, since the AN bolt lacks the strength
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Wait for another internal wrenching bolt, since the AN bolt lacks the strength
Internal wrenching bolts are made from high-strength steel for both tension and shear, and special high-strength nuts are used on them. One is replaced only with another internal wrenching bolt. A standard AN hex head bolt and washer cannot be put in its place, because they do not have the required strength, and no washer or torque value makes up for that.
- Q.04
For an easier pull, you slide a length of pipe over the handle of a rigid-frame, dial-reading torque wrench, with no drive end extension. What does that do to the reading you need?
FAA-H-8083-30B, ch. 7, p. 7-49
- ALower it in proportion to how much longer the pipe makes the handle
- BRaise it, since the pipe makes the wrench read low at the head
- CNothing, since a handle extension alone does not change the reading
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Nothing, since a handle extension alone does not change the reading
The wrench measures the torque at its drive, so lengthening only the handle changes how hard you have to pull, not the reading you need. A handle extension alone has no effect on the reading of this type, so no correction is needed. It is a different story on a flexible beam wrench, where a handle extension is never advisable, and with a drive end extension, which makes the correction formula mandatory on any type.
- Q.05
A new elastic stop nut is stiff to run onto its bolt, and a helper wants to run a tap through the fiber insert first to make it easier. Should he?
FAA-H-8083-30B, ch. 7, p. 7-45
- ANo, the nut locks because the bolt's threads press into fiber with no threads cut in it
- BYes, a tapped insert spares the bolt threads and still locks once the nut is torqued
- CYes, but only for the first installation, after which the insert keeps its own threads
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
No, the nut locks because the bolt's threads press into fiber with no threads cut in it
An elastic stop nut locks because the bolt's threads press their own way into the untapped fiber insert, which then grips them. Run a tap through the insert and the fiber is cut into a thread that simply fits the bolt, so the grip is gone and the nut no longer locks, however hard it is torqued. The stiffness is the locking action at work, not a fault, and there is no first-time exception: the fiber is never tapped.
- Q.06
So its head can be safety wired, you swap a standard AN hex bolt for an AN-73 drilled head bolt of the same size. What does that do to the joint's strength?
FAA-H-8083-30B, ch. 7, p. 7-38
- AIt weakens it, since the drilled head is not as strong, so go up a size
- BNothing that matters, since the 2 series match in tension and shear strength
- CIt limits the bolt to shear loads only, since a drilled head cannot carry tension
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Nothing that matters, since the 2 series match in tension and shear strength
The AN-73 drilled head bolt is like the standard hex bolt but has a deeper head, drilled to take safety wire, and for practical purposes the 2 series are interchangeable in tension and shear strength. So the swap gains a head that can be wired without costing strength. There is no need to go up a size, and the bolt can still carry tension.
- Q.07
An all-metal Boots self-locking nut comes off during an inspection and is still in good condition. May it be installed again?
FAA-H-8083-30B, ch. 7, p. 7-43
- ANo, every self-locking nut has to be thrown away as soon as it comes off a bolt
- BYes, this kind of nut can be removed and reused without losing its grip
- COnly after its locking section has been squeezed tighter with pliers
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Yes, this kind of nut can be removed and reused without losing its grip
The Boots nut has a spring locking section that presses against the bolt threads, so only a wrench will turn it, and it can be removed and reused without impairing its efficiency. So a sound one goes back on. A blanket rule that every self-locking nut is scrapped once removed is wrong for this nut, and squeezing its locking section with pliers is not part of reusing it.
- Q.08
A steel part has to be heated to 1,900 °F, and the shop has both a lead bath and a salt bath. Which one can do the job?
FAA-H-8083-30B, ch. 7, p. 7-14
- AThe lead bath, since lead holds its heat better than salt does
- BEither one, since both kinds of bath reach about 2,450 °F
- CThe salt bath, since a lead bath tops out at about 1,700 °F
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
The salt bath, since a lead bath tops out at about 1,700 °F
Depending on its composition, a salt bath can heat from as low as 325 °F up to as high as 2,450 °F, while a lead bath covers only about 650 °F to 1,700 °F. 1,900 °F is past the lead bath's range, so the salt bath is the one that can do it. Only salt reaches 2,450 °F, and however well lead holds its heat, that does not raise its top temperature.
- Q.09
A bracket is formed from annealed 2024 sheet, since annealed metal bends without cracking, and it goes on the airplane just as it is. What is wrong with that?
FAA-H-8083-30B, ch. 7, p. 7-23
- ANothing, since annealing leaves aluminum alloy at its full strength
- BAluminum alloy is not to be used in the annealed state for parts or fittings
- CNothing, as long as the bend was formed cold and it was never heated again afterward
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
Aluminum alloy is not to be used in the annealed state for parts or fittings
Annealing leaves aluminum alloy in the best condition for cold-working, and a part may even be annealed several times during forming to keep it from cracking. That soft condition is for forming, not for service: aluminum alloys are not to be used in the annealed state for parts or fittings. So the bracket has to be heat treated to the temper its drawing calls for before it is installed.
- Q.10
You quench a shallow-hardening steel part while gripping it with tongs at one end. What should you expect at the spot the tongs covered?
FAA-H-8083-30B, ch. 7, p. 7-19
- AIt may not harden, because the tongs slowed its cooling in the quench
- BIt will come out harder, because the tongs drew heat out of it first
- CIt will crack, because the tongs held that spot hotter than the bath
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
It may not harden, because the tongs slowed its cooling in the quench
Tongs shield the metal they grip from the quenching medium, so that area cools more slowly than the rest. On a steel that hardens only to a shallow depth, the slower cooling can leave the gripped area soft. That is one reason small parts are often wired together or quenched in wire mesh baskets instead of being held by a grip on the surface.
We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.
How a missed code comes back at the oral
Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.I.E. The examiner reads those codes before your oral and practical.
The General oral runs from 4 questions if your written was clean up to 22, because every code you missed adds 1 more. General also carries 9 practical projects, each with 2 questions attached.
Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.
Questions people ask about aircraft materials, hardware and processes
Q.01How do you identify an aircraft bolt?
By the code marks on its head, which show the maker and the material: an AN aluminum alloy bolt carries 2 raised dashes, for example, and a close tolerance NAS bolt a raised or recessed triangle. The part number gives the rest. In AN3DD5A, the 3 is the diameter in 16ths of an inch.
Q.02What does heat treatment do to aluminum alloy?
Solution heat treatment puts as much of the alloying elements as possible into solid solution, which gives the metal its strength. Some alloys, such as 2017 and 2024, then reach full strength by aging at room temperature for about 4 days. Others, such as 2014 and 7075, also need precipitation heat treatment, which is aging at a raised temperature.
Q.03What is the difference between hardness and toughness?
Hardness is a material’s ability to resist abrasion, penetration, cutting and permanent distortion. Toughness is its ability to withstand tearing or shearing and to be stretched or deformed without breaking. They are different properties, and a very hard metal can still be brittle.
Q.04Which way should safety wire pull?
In the direction that tightens the part. The wire is arranged so that if the bolt or screw starts to loosen, the force on the wire works against it. The parts are torqued to their values and the holes lined up before the wire goes on.
Q.05How many aircraft materials, hardware and processes questions are on the FAA A&P General test?
The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Aircraft Materials, Hardware, and Processes subject area 5 to 10% of the General test, which is 3 to 6 of the 60 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.
Q.06Which FAA handbook chapter covers aircraft materials, hardware and processes?
Chapter 7 of FAA-H-8083-30B, the Aviation Maintenance Technician Handbook: General, titled "Aircraft Materials, Hardware, & Processes". It runs from pages 7-1 to 7-80, and the FAA publishes the whole handbook free as a PDF.
Read the documents, not us
Every fact on this page was read from these on 19 August 2026 and 15 November 2026. They are the authority and we are the summary. If we and one of them disagree, they are right.
- FAA-H-8083-30B, Aviation Maintenance Technician Handbook: General, chapter 7www.faa.gov
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standardswww.faa.gov
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards: the written test blueprints (pages 13 and 14) and chapters 6 and 7www.faa.gov
- FAA, Frequently Missed Knowledge Test ACS Codes, 2nd Quarter CY25www.faa.gov
FREE PLAN · NO CARD · 25 QUESTIONS TO START
The bank holds 429 aircraft materials, hardware and processes questions.
Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.
Start freeOr answer a few first. The free FAA A&P practice test runs on the page, with no account.