PrepAMT Academy

AMG · GEN-12 · FAA-H-8083-30B CH. 12

FAA A&P General: Basic Electricity and Electronics

For the FAA A&P General test, aircraft electricity and electronics is chapter 12 of FAA-H-8083-30B, Fundamentals of Electricity & Electronics. Its ACS subject area, Fundamentals of Electricity and Electronics, is 5 to 15% of the test, or 3 to 9 of its 60 scored questions. Our question bank holds 632 questions on it, and the 10 below were written for this page.

Test shares and most-missed codes read from the FAA on 15 November 2026.

01 WHAT IT COVERSFAA-H-8083-30B · CH. 12

What FAA-H-8083-30B chapter 12 covers

Chapter 12 is the longest in the General handbook. It starts with how matter is made up, the metric prefixes used in electrical work, static electricity and magnetism, then voltage, current and resistance, Ohm’s law and power. It works through series, parallel and series-parallel DC circuits with Kirchhoff’s laws, then alternating current: frequency and phase, capacitance and inductance, reactance and impedance, and transformers.

The second half covers the meters and the oscilloscope, and how to trace opens and shorts with them; batteries, lead-acid, nickel-cadmium and lithium-ion; semiconductors, transistors and logic circuits; then DC generators, motors, alternators, and the regulators and control units that govern them.

It runs from pages 12-1 to 12-174 of the Aviation Maintenance Technician Handbook: General, which the FAA publishes free as a PDF.

02 SHARE OF THE TESTFAA-G-ACS-1 · BLUEPRINT

How much of the FAA A&P General test it is

  • 5 to 15%OF THE TESTACS area AM.I.A
  • 3 to 9QUESTIONSof 60 scored
  • 632IN OUR BANKquestions on this subject

The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Fundamentals of Electricity and Electronics (AM.I.A) is 5 to 15% (3 to 9 questions) on the 60-question General test. The 12 ranges for the General test add up to anywhere from 60% to 130%, so they say how big an area can get, not how many questions you will see from it.

The FAA’s latest report on the most-missed codes (2nd Quarter, CY25, 1 July 2024 to 30 June 2025) lists AM.I.A.K24, “Electrostatic discharge”, in this area, missed 74.91% of the time on the General test. That is a whole subject element across everyone who took the test, not one question, and it is the part of this subject the FAA says people get wrong most.

03 EXAMPLE QUESTIONSWRITTEN FOR THIS PAGE

Aircraft electricity and electronics questions and answers

10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.

  1. Q.01

    Why is a nickel-cadmium emergency battery pack given its scheduled energy test on the bench rather than on the aircraft?

    FAA-H-8083-30B, ch. 12, p. 12-93

    1. AIts charge cannot be measured installed, and voltage depression can mask a weak one
    2. BIts cells must first be warmed to a set temperature by a bench heater
    3. CTesting it in place would discharge the aircraft's main battery along with it
    SHOW THE ANSWER

    THE ANSWER IS A.

    Its charge cannot be measured installed, and voltage depression can mask a weak one

    A Ni-Cad emergency pack needs its scheduled energy test on the bench, because its energy level cannot be measured while it is on the aircraft. It also suffers voltage depression, often wrongly called memory, which shows only on a full discharge, so the pack can seem fully charged when it is not. Sealed lead-acid packs can be designed to be tested while still installed.

  2. Q.02

    In a room where nickel-cadmium batteries are charged, ventilation should keep the hydrogen in closed spaces from building up past what level?

    FAA-H-8083-30B, ch. 12, p. 12-92

    1. A4 percent by volume
    2. B10 percent by volume
    3. C1 percent by volume
    SHOW THE ANSWER

    THE ANSWER IS C.

    1 percent by volume

    Overcharged Ni-Cad cells give off an explosive mix of hydrogen and oxygen, and the cell relief valves vent it to the atmosphere. Ventilation should stop the hydrogen in closed spaces from going above 1 percent by volume. Explosions can happen at concentrations above 4 percent, so 4 percent is the danger point rather than the limit, and 10 percent is well past it.

  3. Q.03

    You connect an analog DC voltmeter to a circuit with its leads the wrong way round. What is likely to happen?

    FAA-H-8083-30B, ch. 12, p. 12-71

    1. AIt reads the right value, since the movement ignores polarity
    2. BThe movement is driven backward and can be damaged
    3. CIt reads twice the true value until the leads are swapped
    SHOW THE ANSWER

    THE ANSWER IS B.

    The movement is driven backward and can be damaged

    A DC meter movement moves up scale only when current flows through its coil in the right direction. With the leads reversed, the pointer is driven backward, which can damage the movement and often bends the needle. So check the polarity markings before connecting the meter. Polarity does matter to the movement, and reversing it does not double the reading.

  4. Q.04

    A technician wants to see how much current a battery can deliver and is about to clip an ammeter straight across its terminals. What will happen?

    FAA-H-8083-30B, ch. 12, p. 12-70

    1. AThe meter shows the battery's ampere-hour capacity
    2. BA very large current flows through the meter and damages it
    3. CNothing harmful, since the meter's shunt limits the current
    SHOW THE ANSWER

    THE ANSWER IS B.

    A very large current flows through the meter and damages it

    An ammeter has very low resistance, especially on its higher ranges, so connecting it across a battery or generator lets even a volt or so drive a very high current through it, and the meter is damaged. An ammeter belongs in series, in the path of the current being measured. Its shunt only carries part of the current around the movement and does nothing to limit it, and no meter reading shows ampere-hour capacity.

  5. Q.05

    A lead-acid battery has been on the shop charger, and you are about to take it off. What should you do before unclipping it?

    FAA-H-8083-30B, ch. 12, p. 12-91

    1. APull the clips off quickly so they have no time to arc
    2. BTighten the vent caps so no gas escapes as the battery moves
    3. CSwitch the charger off at its remote switch first
    SHOW THE ANSWER

    THE ANSWER IS C.

    Switch the charger off at its remote switch first

    A charging battery gives off hydrogen and oxygen, an explosive mix, so nothing that could spark or flame is allowed near it. Before a battery is connected to or disconnected from the charger, the power is turned off with a remote switch, so no spark forms at the clips. The vent caps are loosened and left in place during charging, not tightened, and pulling live clips off quickly is just how a spark is made.

  6. Q.06

    Measuring across the same high-resistance part, a meter rated 1,000 ohms per volt and one rated 20,000 ohms per volt disagree. Which reading is closer to the truth?

    FAA-H-8083-30B, ch. 12, p. 12-71

    1. AThe 20,000 ohms per volt meter, since it draws less current from the circuit
    2. BThe 1,000 ohms per volt meter, since more current through it gives a firmer reading
    3. CThey should read alike, so one of the meters must be out of calibration
    SHOW THE ANSWER

    THE ANSWER IS A.

    The 20,000 ohms per volt meter, since it draws less current from the circuit

    A voltmeter is connected in parallel, so some current is shunted through it. A low-resistance meter draws off enough current to lower the circuit's effective resistance and change the very voltage it is reading. That is why a high-resistance voltmeter is used: the 20,000 ohms per volt meter loads the circuit far less. Good meters of different sensitivity can disagree for just this reason, without either being out of calibration.

  7. Q.07

    An AC motor on the bench runs, but with a regular knocking sound rather than an even hum. What does a knocking sound generally point to?

    FAA-H-8083-30B, ch. 12, p. 12-154

    1. AAn overload, which makes the motor labor and knock under the extra load
    2. BA loose armature coil, a shaft out of line or worn bearings letting it drag
    3. CA 3-phase supply with one of its leads disconnected from the motor
    SHOW THE ANSWER

    THE ANSWER IS B.

    A loose armature coil, a shaft out of line or worn bearings letting it drag

    Next to temperature, the sound of a motor is the best trouble indicator. Running properly it hums evenly, overloaded it grunts, and a 3-phase motor with one lead disconnected will not turn at all and growls. A knocking sound generally means something mechanical: a loose armature coil, a shaft out of alignment, or the armature dragging on worn bearings.

  8. Q.08

    You need to read a small voltage in a high-resistance, low-power circuit, and the only meter at hand has a moving iron vane movement. Why is it a poor choice for this job?

    FAA-H-8083-30B, ch. 12, p. 12-75

    1. AIt cannot read DC at all, so it shows nothing on that circuit
    2. BIts moving element carries the circuit current and can burn out
    3. CIt needs far more power for full-scale deflection than a d'Arsonval meter
    SHOW THE ANSWER

    THE ANSWER IS C.

    It needs far more power for full-scale deflection than a d'Arsonval meter

    The magnetic circuit of a moving iron vane meter has high reluctance, so the meter needs much more power to reach full-scale deflection than a d'Arsonval movement of the same range. That is why it is seldom used in high-resistance, low-power circuits. No current is conducted to its moving element, and it can read DC, though with an error from residual magnetism in the vanes. Being simple and cheap, it is widely used in AC power circuits instead.

  9. Q.09

    A meter movement reads full scale at 1 milliampere and has a coil resistance of 100 ohms. What multiplier resistor makes it a voltmeter that reads 10 volts full scale?

    FAA-H-8083-30B, ch. 12, p. 12-70

    1. A9,900 ohms
    2. B10,000 ohms
    3. C10,100 ohms
    SHOW THE ANSWER

    THE ANSWER IS A.

    9,900 ohms

    The multiplier sits in series with the movement and drops the voltage the movement does not need. At full scale the whole meter, multiplier and coil together, passes 1 milliampere with 10 volts across it, so its total resistance is 10 divided by 0.001, which is 10,000 ohms. The coil supplies 100 ohms of that, which leaves 10,000 minus 100, or 9,900 ohms, for the multiplier. 10,000 ohms forgets the coil, and 10,100 ohms adds it instead of taking it away.

  10. Q.10

    A lead-acid battery has often been charged and discharged too fast. Now it runs itself down while it sits unused. What is the likely cause?

    FAA-H-8083-30B, ch. 12, p. 12-89

    1. ASulfation from the fast charging has sealed the plates against the acid
    2. BMaterial shed from overheated plates has built up and shorted the plates
    3. CThe fast charging has turned the electrolyte into plain water
    SHOW THE ANSWER

    THE ANSWER IS B.

    Material shed from overheated plates has built up and shorted the plates

    Charging or discharging a lead-acid battery too fast overheats its plates and makes them shed active material. That shed material builds up and shorts the plates, so the battery discharges internally even with nothing connected. Excess sulfation is the damage done by over-discharging, and fast charging does not turn the electrolyte into water.

We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.

04 AND THEN THE ORAL§ 65.79

How a missed code comes back at the oral

Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.I.A. The examiner reads those codes before your oral and practical.

The General oral runs from 4 questions if your written was clean up to 22, because every code you missed adds 1 more. General also carries 9 practical projects, each with 2 questions attached.

Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.

05 COMMON QUESTIONSFAQ

Questions people ask about aircraft electricity and electronics

Q.01

What is Ohm’s law?

Voltage equals current times resistance. So current is voltage divided by resistance, and resistance is voltage divided by current. A 12 volt source across a 4 ohm resistor drives 3 amps through it.

Q.02

What is the difference between a series and a parallel circuit?

A series circuit has one path, so the same current flows through every part and the voltage drops add up to the source voltage. In a parallel circuit every branch has the full source voltage across it and the branch currents add up to the total. Adding a branch in parallel lowers the total resistance.

Q.03

What are Kirchhoff’s laws?

The voltage law says that around any closed loop of a circuit, the voltage drops add up to the source voltage. The current law says that the current flowing into any junction equals the current flowing out of it.

Q.04

How do you find an open in a series circuit with a voltmeter?

With the circuit powered, no current flows anywhere in the loop, so a good component shows almost no voltage across it, while the meter across the open reads the full source voltage. With the power off, an ohmmeter across the open reads infinite resistance.

Q.05

How many aircraft electricity and electronics questions are on the FAA A&P General test?

The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Fundamentals of Electricity and Electronics subject area 5 to 15% of the General test, which is 3 to 9 of the 60 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.

Q.06

Which FAA handbook chapter covers aircraft electricity and electronics?

Chapter 12 of FAA-H-8083-30B, the Aviation Maintenance Technician Handbook: General, titled "Fundamentals of Electricity & Electronics". It runs from pages 12-1 to 12-174, and the FAA publishes the whole handbook free as a PDF.

FREE PLAN · NO CARD · 25 QUESTIONS TO START

The bank holds 632 aircraft electricity and electronics questions.

Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.

Start free

Or answer a few first. The free FAA A&P practice test runs on the page, with no account.