PrepAMT Academy

AMG · GEN-10 · FAA-H-8083-30B CH. 10

FAA A&P General: Inspection Concepts and Techniques

For the FAA A&P General test, aircraft inspection concepts and techniques is chapter 10 of FAA-H-8083-30B, Inspection Concepts & Techniques. Its ACS subject area, Inspection Concepts and Techniques, is 5 to 10% of the test, or 3 to 6 of its 60 scored questions. Our question bank holds 281 questions on it, and the 10 below were written for this page.

Test shares and most-missed codes read from the FAA on 15 November 2026.

01 WHAT IT COVERSFAA-H-8083-30B · CH. 10

What FAA-H-8083-30B chapter 10 covers

Chapter 10 is how and why aircraft are inspected. It covers the basics of an inspection, aircraft logs, checklists and the publications an inspection is done against, then the routine and required inspections: preflight, annual and 100-hour, progressive and continuous programs, the ATA iSpec 2200 chapter numbers, special inspections such as after a hard landing or a lightning strike, and special flight permits.

The rest is nondestructive inspection and testing: visual inspection and its aids, liquid penetrant, eddy current, ultrasonic, magnetic particle and radiographic inspection, what each one finds and its limits, and how bonded structures, composites and welds are inspected.

It runs from pages 10-1 to 10-39 of the Aviation Maintenance Technician Handbook: General, which the FAA publishes free as a PDF.

02 SHARE OF THE TESTFAA-G-ACS-1 · BLUEPRINT

How much of the FAA A&P General test it is

  • 5 to 10%OF THE TESTACS area AM.I.K
  • 3 to 6QUESTIONSof 60 scored
  • 281IN OUR BANKquestions on this subject

The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Inspection Concepts and Techniques (AM.I.K) is 5 to 10% (3 to 6 questions) on the 60-question General test. The 12 ranges for the General test add up to anywhere from 60% to 130%, so they say how big an area can get, not how many questions you will see from it.

Inspection Concepts and Techniques is not ours alone to cover: our Hand Tools and Measuring Devices questions are written to the same area.

No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.

03 EXAMPLE QUESTIONSWRITTEN FOR THIS PAGE

Aircraft inspection concepts and techniques questions and answers

10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.

  1. Q.01

    Small steel parts are to be demagnetized in an AC coil a good deal bigger than they are. Where in the coil are they held for the best effect?

    FAA-H-8083-30B, ch. 10, p. 10-34

    1. AOn the coil's center line, as far from the windings as possible
    2. BAs close to the inner wall of the coil as possible
    3. CJust outside the end of the coil, never inside it
    SHOW THE ANSWER

    THE ANSWER IS B.

    As close to the inner wall of the coil as possible

    Demagnetizing uses a coil carrying alternating current, and a part loses its magnetism as it is drawn away from the alternating field. Ideally the coil is about the size of the work. When small parts go into a bigger coil, they are held as close to its inner wall as possible for maximum effectiveness, not out on its center line. Parts are passed through the coil and drawn slowly out of it, not held outside it.

  2. Q.02

    You are searching a wing skin for cracks with a flashlight held at a low angle to the surface. Where should your eyes be?

    FAA-H-8083-30B, ch. 10, p. 10-18

    1. AIn line with the reflected beam, to catch the brightest glint
    2. BAbove the reflected beam, so it does not shine into your eyes
    3. CDown at surface level, looking along the length of the beam
    SHOW THE ANSWER

    THE ANSWER IS B.

    Above the reflected beam, so it does not shine into your eyes

    For surface cracks the flashlight beam is aimed at a low angle, 5 to 45 degrees to the surface. It must not be angled so that the reflected beam shines straight into your eyes, so you keep your eyes above the reflected beam while you look. Once a crack is found, the beam is aimed at right angles across it to trace how long it is.

  3. Q.03

    On a progressive inspection program, an airplane had its first phase done and then sat for months with later phases still open. By when must the remaining phases be completed?

    FAA-H-8083-30B, ch. 10, p. 10-12

    1. ABy the end of the 12th month from the first phase
    2. BWithin 12 months of whichever phase was done most recently
    3. CAt the next annual date shown in the aircraft's records
    SHOW THE ANSWER

    THE ANSWER IS A.

    By the end of the 12th month from the first phase

    A progressive program splits the annual into phases, and a full cycle has to be completed within 12 months. If all the phases are not done in that time, the remaining ones must be done before the end of the 12th month from when the first phase was completed. The clock runs from the first phase, not the latest one, and the completed cycle is what stands in for the annual, so there is no annual date to wait for.

  4. Q.04

    After a flight through severe turbulence, you find a sizeable fuel leak along a seam in the wing. What does that leak suggest?

    FAA-H-8083-30B, ch. 10, p. 10-15

    1. AOnly that the old sealant has aged and can be touched up later
    2. BThat the wing may have been overloaded enough to open the seam
    3. CThat the tank was overfilled and vented, which is normal in turbulence
    SHOW THE ANSWER

    THE ANSWER IS B.

    That the wing may have been overloaded enough to open the seam

    After severe turbulence, a sizeable fuel leak is a sign that the area may have taken loads big enough to break the sealant and open the seams. It calls for a closer look at the structure, such as the spar webs, skin wrinkles and attachments, and the inspection goes on until all the damage is found. Putting the leak down to aged sealant or venting would leave possible structural damage unchecked.

  5. Q.05

    An aerial application airplane spends almost all of its working time flying at very low altitude. Which part of it tends to clog up faster than on other airplanes?

    FAA-H-8083-30B, ch. 10, p. 10-16

    1. AThe fuel tank vent lines
    2. BThe engine air filters
    3. CThe pitot and static ports
    SHOW THE ANSWER

    THE ANSWER IS B.

    The engine air filters

    Because aerial application airplanes operate almost continuously at very low altitude, their air filters become obstructed more quickly than on other airplanes, so they need attention more often. The same work brings corrosive chemicals and many takeoffs and landings a day from rough strips, which call for close corrosion checks and frequent checks of fatigue items and landing gear.

  6. Q.06

    A gas weld has an even width, even ripples feathered into the base metal and excellent penetration, but the edges of the bead wander instead of running straight. How should the wandering edges be judged?

    FAA-H-8083-30B, ch. 10, p. 10-38

    1. AAs a fault, since the edges of a good bead run in a straight line
    2. BAs a fault, since wandering edges mean cold laps under the bead
    3. CAs no fault, since a sound weld need not have perfectly straight edges
    SHOW THE ANSWER

    THE ANSWER IS C.

    As no fault, since a sound weld need not have perfectly straight edges

    A good weld is uniform in width, its ripples are even and well feathered into the base metal, and it has good penetration with no gas pockets, porosity or inclusions. Its edges do not have to run in a straight line: a bead whose edges wander is still a good weld when its penetration is excellent. Cold laps come from too little heat and show as rough, irregular edges that are not feathered in, which is not this weld.

  7. Q.07

    After one slow pass out of an AC demagnetizing coil, a steel part still holds some magnetism. What should you do next?

    FAA-H-8083-30B, ch. 10, p. 10-34

    1. ALeave it inside the coil with the current on for a few more minutes
    2. BHold a permanent magnet against it to cancel the field
    3. CPass it slowly in and out several times, turning it as you go
    SHOW THE ANSWER

    THE ANSWER IS C.

    Pass it slowly in and out several times, turning it as you go

    Parts that do not readily lose their magnetism are passed slowly in and out of the demagnetizer several times while being tumbled or turned in different directions. It is the slow movement out of the alternating field that does the work, so leaving a part sitting in the coil with the current on does very little. A permanent magnet only adds a field of its own. On the last pass the current stays on until the part is 1 or 2 feet away.

  8. Q.08

    A finished gas weld shows slight bumps along its center and craters at its finish. What most likely went wrong while it was being made?

    FAA-H-8083-30B, ch. 10, p. 10-38

    1. AToo much acetylene, which made the puddle boil
    2. BToo little heat, which left the edges rough and cold-lapped
    3. CA neutral flame held in one place, which burned through
    SHOW THE ANSWER

    THE ANSWER IS A.

    Too much acetylene, which made the puddle boil

    When too much acetylene is used, the puddle tends to boil during welding, and that often leaves slight bumps along the center of the bead and craters at the finish. Too little heat shows instead as a rough, irregular bead with cold laps and edges not feathered into the base metal. A flame held too long in one place melts a hole, which is a different fault from bumps and craters.

  9. Q.09

    Thermography is often chosen for inspecting thin composite structure. Why can it show damage in composite parts well with only a small heat input?

    FAA-H-8083-30B, ch. 10, p. 10-37

    1. AComposites spread heat far less than aluminum and have a higher emissivity
    2. BComposites conduct heat better than aluminum, so the heat spreads evenly
    3. CComposites reflect infrared, so the camera sees the heat lamp's image
    SHOW THE ANSWER

    THE ANSWER IS A.

    Composites spread heat far less than aluminum and have a higher emissivity

    Thermography warms the surface a few degrees and an infrared camera maps the heat, since damaged and sound areas conduct heat differently. Aluminum carries heat away fast, so a small rise soon evens out. A composite keeps the heat near where it went in, and its higher emissivity gives the camera a strong reading, so a smaller heat input shows damage better. The handbook's way of putting this is that composites do not radiate heat nearly as much as aluminum. The camera reads the heat the part gives off, not a reflection of the lamp.

  10. Q.10

    To save time before a wet magnetic particle inspection, a technician plans to let the particle suspension wash the grease off the part. Why is that a poor plan?

    FAA-H-8083-30B, ch. 10, p. 10-30

    1. AThe grease makes the suspension dry out on the part before it can be read
    2. BThe suspension is so strong that it would etch the surface as it cleans
    3. CIt cleans poorly, and the dirt it takes off contaminates the suspension
    SHOW THE ANSWER

    THE ANSWER IS C.

    It cleans poorly, and the dirt it takes off contaminates the suspension

    Parts are cleaned before magnetic particle inspection, because grease and other foreign material can hold particles and give indications that mean nothing. The suspension is no substitute for that cleaning: it does not clean thoroughly, and whatever it does wash off ends up in the suspension and makes it less effective.

We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.

04 AND THEN THE ORAL§ 65.79

How a missed code comes back at the oral

Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.I.K. The examiner reads those codes before your oral and practical.

The General oral runs from 4 questions if your written was clean up to 22, because every code you missed adds 1 more. General also carries 9 practical projects, each with 2 questions attached.

Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.

05 COMMON QUESTIONSFAQ

Questions people ask about aircraft inspection concepts and techniques

Q.01

What is the difference between an annual and a 100-hour inspection?

They cover the same items, which 14 CFR Part 43 Appendix D lists. The differences are who may do them and when they apply. Almost every aircraft needs an annual; one that carries people for hire or is used for flight instruction for hire also needs a 100-hour inspection. An FAA A&P mechanic can do a 100-hour inspection, but an annual needs a mechanic who also holds an inspection authorization.

Q.02

What does dye penetrant inspection find?

Defects that are open to the surface, such as cracks, laps and porosity, in nonporous material. The penetrant soaks into the defect, the excess is cleaned off, and a developer draws it back out so the defect shows. It cannot find anything below the surface.

Q.03

What is eddy current inspection used for?

Finding cracks, corrosion and heat damage in metals that conduct electricity, at or near the surface. A coil carrying alternating current sets up small currents in the part, and a flaw changes them in a way the instrument shows. It also reads changes in alloy and heat treat condition, which is how heat damage in aluminum is found.

Q.04

What is magnetic particle inspection?

A way to find surface and near surface flaws in parts that can be magnetized, such as steel. The part is magnetized and iron particles are applied; a flaw breaks up the magnetic field and the particles gather over it. It will not work on aluminum or other nonmagnetic metals.

Q.05

How many aircraft inspection concepts and techniques questions are on the FAA A&P General test?

The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Inspection Concepts and Techniques subject area 5 to 10% of the General test, which is 3 to 6 of the 60 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.

Q.06

Which FAA handbook chapter covers aircraft inspection concepts and techniques?

Chapter 10 of FAA-H-8083-30B, the Aviation Maintenance Technician Handbook: General, titled "Inspection Concepts & Techniques". It runs from pages 10-1 to 10-39, and the FAA publishes the whole handbook free as a PDF.

FREE PLAN · NO CARD · 25 QUESTIONS TO START

The bank holds 281 aircraft inspection concepts and techniques questions.

Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.

Start free

Or answer a few first. The free FAA A&P practice test runs on the page, with no account.