AMG · GEN-09 · FAA-H-8083-30B CH. 9
FAA A&P General: Fluid Lines and Fittings
For the FAA A&P General test, aircraft fluid lines and fittings is chapter 9 of FAA-H-8083-30B, Fluid Lines & Fittings. Its ACS subject area, Fluid Lines and Fittings, is 5 to 10% of the test, or 3 to 6 of its 60 scored questions. Our question bank holds 213 questions on it, and the 10 below were written for this page.
Test shares and most-missed codes read from the FAA on 15 November 2026.
What FAA-H-8083-30B chapter 9 covers
Chapter 9 covers the plumbing that carries fuel, oil, hydraulic fluid, oxygen and air. For rigid lines it covers the tubing materials and how to identify them, sizes, cutting, bending, single and double flaring, beading, and the fittings that join them, flared and flareless.
For flexible hose it covers the hose materials, the identification markings and the lay line printed along the hose, sizing, fittings, and how to make up, install and inspect a hose assembly. It also covers line identification markings, clamps and supports.
It runs from pages 9-1 to 9-23 of the Aviation Maintenance Technician Handbook: General, which the FAA publishes free as a PDF.
How much of the FAA A&P General test it is
- 5 to 10%OF THE TESTACS area AM.I.D
- 3 to 6QUESTIONSof 60 scored
- 213IN OUR BANKquestions on this subject
The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Fluid Lines and Fittings (AM.I.D) is 5 to 10% (3 to 6 questions) on the 60-question General test. The 12 ranges for the General test add up to anywhere from 60% to 130%, so they say how big an area can get, not how many questions you will see from it.
No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.
Aircraft fluid lines and fittings questions and answers
10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.
- Q.01
A replacement rigid line is to run between 2 fittings that line up exactly, so a straight tube would reach. How should the new tube be made?
FAA-H-8083-30B, ch. 9, p. 9-16
- AStraight, since a straight run is the strongest and lightest
- BWith bends in it, since a straight tube cannot be fitted free of strain
- CStraight, then pulled into place by tightening the coupling nuts
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
With bends in it, since a straight tube cannot be fitted free of strain
A tube can never be cut or flared exactly enough to go in straight and still be free of mechanical strain, so a path with no bends is never chosen. The bends also let the tube expand and contract with temperature and soak up vibration. Pulling a tube into line with its coupling nuts is just what must be avoided: the new assembly should be formed so it meets the fittings without being forced.
- Q.02
A flared tube fitting was tightened to its specified torque when it went in. What does that mean if the line has to be disconnected during later maintenance?
FAA-H-8083-30B, ch. 9, p. 9-12
- AThe flare must be cut off and made again each time the nut is loosened
- BIt may be removed and retightened many times before it needs reflaring
- CIt may be reconnected once, after which the sleeve and nut are replaced
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
It may be removed and retightened many times before it needs reflaring
A tube fitting that is tightened properly, with a torque wrench to the specified value, can be taken apart and tightened again many times before the tube has to be reflared. It is overtightening that damages or cuts off the flare and ruins the sleeve or nut, and undertightening that lets the line blow out or leak.
- Q.03
A hose has to be replaced in a system that runs on Skydrol, and the only hose of the right size on the shelf is Buna-N. What do you do?
FAA-H-8083-30B, ch. 9, p. 9-16
- AFit it, since a wire braid hose of the right pressure class suits any fluid
- BFit it, but lubricate its fittings with petroleum grease as it goes on
- CDo not fit it, since Buna-N must not be used with phosphate ester fluid
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
Do not fit it, since Buna-N must not be used with phosphate ester fluid
Buna-N stands up well to petroleum products, but it must not be used with phosphate ester base hydraulic fluid such as Skydrol, and neither may neoprene. Hose for that system is marked for Skydrol use. The pressure class says nothing about which fluid a hose can carry, and no petroleum product goes on hose meant for synthetic fluid, so the grease would make things worse, not better.
- Q.04
A rigid fluid line has a crushed section and must be replaced, but the fittings at its ends are still in good condition. What does the job usually come down to?
FAA-H-8083-30B, ch. 9, p. 9-2
- ASaving the fittings, so the work is forming and fitting a new tube
- BA complete new line with new fittings, since used fittings are scrapped
- CBurnishing out the crushed section, since the fittings are still good
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Saving the fittings, so the work is forming and fitting a new tube
When a fluid line assembly is replaced, its fittings can often be salvaged, so the repair is only a matter of forming a new tube and fitting it in place. Burnishing is for minor scratches and abrasions, not a crushed tube, and good fittings need not be thrown away with the old tube.
- Q.05
A dent has to be taken out of a short, straight piece of soft aluminum tubing, and the shop has no steel bullet of the right size. What can serve as the bullet?
FAA-H-8083-30B, ch. 9, p. 9-15
- ANothing, since only a hardened steel bullet will reshape the tube
- BA hard wood slug or dowel of the right size
- CA soft rubber plug pulled through on a cable
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
A hard wood slug or dowel of the right size
A dent is removed by drawing a bullet of the proper size through the tube on a length of cable, or by pushing it through a short straight tube with a rod. The bullet is normally steel or some other hard metal, but in soft aluminum tubing a hard wood slug or dowel may be used instead. A soft rubber plug has none of the hardness needed to push the dent back out.
- Q.06
There is no tube cutter suited to the hard tubing you have to cut, so you use a fine-tooth hacksaw. What does sawing do for the tube, compared with a cutter?
FAA-H-8083-30B, ch. 9, p. 9-2
- AIt leaves a square end that needs no filing before flaring
- BIt hardens the cut end, which helps the flare hold its shape
- CIt work-hardens the tubing less during the cutting operation
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
It work-hardens the tubing less during the cutting operation
Hard tubing, or any tubing when no cutter is at hand, is cut with a fine-tooth hacksaw, and sawing work-hardens the tube less during the cut. The sawn end still has to be filed square and smooth and deburred before it is flared, and hardening the end is the opposite of what you want for a good flare.
- Q.07
You are about to install an MS flareless tube assembly, and the only chart at hand is the torque table for flared tube fittings. Should you torque the flareless nut by that table?
FAA-H-8083-30B, ch. 9, p. 9-10
- ANo, the values in that table are for flared fittings only
- BYes, the table covers every fitting made for that tube size
- CYes, provided the tube and the fitting are both aluminum alloy
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
No, the values in that table are for flared fittings only
The torque table for tube fittings gives values for flared-type fittings only. A flareless nut is normally run down until it bottoms and then turned a set amount, one-sixth of a turn, unless the aircraft manufacturer lists torque values for it in the maintenance manual. Neither the tube size nor the material makes the flared table apply to a flareless fitting.
- Q.08
While installing a flexible hose, a coworker suggests clamping a small bracket to it so that the hose helps hold the bracket in place. What do you tell him?
FAA-H-8083-30B, ch. 9, p. 9-21
- AThat is fine, as long as the hose is a high-pressure type with steel braid
- BThat is fine, as long as the bracket weighs less than the hose assembly
- CNo, a hose must not be installed so that it carries a mechanical load
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS C.
No, a hose must not be installed so that it carries a mechanical load
Hose assemblies must not be installed in a way that puts a mechanical load on the hose, and a bracket hanging on it is exactly that. A steel braid protects the hose from damage; it does not make the hose a structural member, and how light the bracket is makes no difference. The bracket needs its own support.
- Q.09
Rigid tubing is pressure tested before it is first installed. Compared with the normal operating pressure of the system it goes in, what pressure is the tubing designed to withstand?
FAA-H-8083-30B, ch. 9, p. 9-1
- ASeveral times the normal operating pressure of its system
- BThe normal operating pressure, plus a 10 percent margin
- CAbout the system relief valve setting, which caps the pressure
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS A.
Several times the normal operating pressure of its system
All tubing is pressure tested before it is first installed, and it is designed to withstand several times the normal operating pressure it will see. So a tube that bursts or cracks in service has usually been weakened by vibration, poor installation or damage, and the cause must be found. A small margin over normal pressure, or a limit set by the relief valve, is not what tubing is built to.
- Q.10
A medium-pressure Teflon hose comes off the airplane already bent into a fixed shape. Why was it made that way?
FAA-H-8083-30B, ch. 9, p. 9-17
- ASo it can be straightened out later if a longer run is needed
- BTo clear obstructions with the shortest possible hose length
- CTo keep it from expanding in diameter when it is pressurized
SHOW THE ANSWERHIDE THE ANSWER
THE ANSWER IS B.
To clear obstructions with the shortest possible hose length
Medium-pressure Teflon hose assemblies are sometimes preformed to clear obstructions and to make their connections with the shortest possible hose length. Preforming permits tighter bends that do away with special elbows, which saves space and weight. A preformed hose must never be straightened, and a support wire holds its shape while it is off the airplane. Teflon has less volumetric expansion than rubber whatever its shape.
We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.
How a missed code comes back at the oral
Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.I.D. The examiner reads those codes before your oral and practical.
The General oral runs from 4 questions if your written was clean up to 22, because every code you missed adds 1 more. General also carries 9 practical projects, each with 2 questions attached.
Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.
Questions people ask about aircraft fluid lines and fittings
Q.01What is the lay line on a flexible hose for?
Lay lines are printed along the hose with its identification markings, and they follow the natural lay of the hose, with no twist. Once the hose is installed the lay line should still run straight. A lay line that spirals around the hose shows it was twisted when it went in.
Q.02What is the difference between a single flare and a double flare?
A single flare spreads the end of the tube into a cone. A double flare folds the end back on itself first, so the flare is 2 layers thick. It is used on soft aluminum alloy tubing of 3/8 inch outside diameter and under, so the flare is not cut off under pressure. It is smoother and more concentric than a single flare, so it seals better.
Q.03How is the size of a rigid tube given?
By its outside diameter in 16ths of an inch, so a number 6 tube is 6/16, or 3/8, of an inch across. The wall thickness is given separately, in thousandths of an inch.
Q.04How do you know what a fluid line carries?
From its markers, made up of color codes, words and geometric symbols that name the line’s function, what it carries and its main hazard. They are usually 1 inch tape or decals at both ends of the line and at least once in every compartment it runs through. Steel tags may take their place on large, hot or oily lines, and paint is used in engine compartments, where a tape or tag could be drawn into the induction system.
Q.05How many aircraft fluid lines and fittings questions are on the FAA A&P General test?
The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Fluid Lines and Fittings subject area 5 to 10% of the General test, which is 3 to 6 of the 60 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.
Q.06Which FAA handbook chapter covers aircraft fluid lines and fittings?
Chapter 9 of FAA-H-8083-30B, the Aviation Maintenance Technician Handbook: General, titled "Fluid Lines & Fittings". It runs from pages 9-1 to 9-23, and the FAA publishes the whole handbook free as a PDF.
Read the documents, not us
Every fact on this page was read from these on 19 August 2026 and 15 November 2026. They are the authority and we are the summary. If we and one of them disagree, they are right.
- FAA-H-8083-30B, Aviation Maintenance Technician Handbook: General, chapter 9www.faa.gov
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standardswww.faa.gov
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards: the written test blueprints (pages 13 and 14) and chapters 6 and 7www.faa.gov
- FAA, Frequently Missed Knowledge Test ACS Codes, 2nd Quarter CY25www.faa.gov
FREE PLAN · NO CARD · 25 QUESTIONS TO START
The bank holds 213 aircraft fluid lines and fittings questions.
Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.
Start freeOr answer a few first. The free FAA A&P practice test runs on the page, with no account.