PrepAMT Academy

AMG · GEN-01 · FAA-H-8083-30B CH. 1

FAA A&P General: Safety, Ground Operations and Servicing

For the FAA A&P General test, aircraft ground operations and servicing is chapter 1 of FAA-H-8083-30B, Safety, Ground Operations, & Servicing. Its main ACS subject area, Ground Operations and Servicing, is 5 to 15% of the test, or 3 to 9 of its 60 scored questions. Our question bank holds 246 questions on it, and the 10 below were written for this page.

Test shares and most-missed codes read from the FAA on 15 November 2026.

01 WHAT IT COVERSFAA-H-8083-30B · CH. 1

What FAA-H-8083-30B chapter 1 covers

Chapter 1 starts with safety in the shop and on the flight line: electrical safety, compressed gases, hazardous materials, machine tools, hearing protection and foreign object damage, and working around turning propellers and helicopter rotors. It then covers fire: what a fire needs, the classes of fire, and which extinguisher goes on which.

The rest is ground operations and servicing. It covers tying aircraft down, seaplanes, ski planes and helicopters included; starting reciprocating, turboprop and turbofan engines, and what to do about a hung or hot start; towing and taxiing with the standard signals; and servicing air, nitrogen, oil, hydraulic fluid, oxygen and fuel, with the fueling hazards and contamination checks that go with it.

It runs from pages 1-1 to 1-28 of the Aviation Maintenance Technician Handbook: General, which the FAA publishes free as a PDF.

02 SHARE OF THE TESTFAA-G-ACS-1 · BLUEPRINT

How much of the FAA A&P General test it is

  • 5 to 15%OF THE TESTACS area AM.I.F
  • 3 to 9QUESTIONSof 60 scored
  • 246IN OUR BANKquestions on this subject

The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Ground Operations and Servicing (AM.I.F) is 5 to 15% (3 to 9 questions) on the 60-question General test. Our Safety, Ground Operations and Servicing questions also reach into Human Factors (AM.I.L, 5 to 10%). The 12 ranges for the General test add up to anywhere from 60% to 130%, so they say how big an area can get, not how many questions you will see from it.

No code in these areas is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.

03 EXAMPLE QUESTIONSWRITTEN FOR THIS PAGE

Aircraft ground operations and servicing questions and answers

10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.

  1. Q.01

    The marking on a hangar wall calls for a Class B extinguisher, but the one hanging under it is a water type. What should be done?

    FAA-H-8083-30B, ch. 1, p. 1-8

    1. ALeave it, since water cools the fire and puts out most kinds
    2. BHang one suitable for Class B fires there, as the marking shows
    3. CLeave it, as long as a Class B unit hangs elsewhere in the hangar
    SHOW THE ANSWER

    THE ANSWER IS B.

    Hang one suitable for Class B fires there, as the marking shows

    A location marking promises whoever runs to it a certain kind of extinguisher, so the one kept there must be the type the marking shows. Water is the wrong agent for a Class B fire anyway: most petroleum products float on water, so water-type extinguishers are not recommended for them. A suitable extinguisher somewhere else in the hangar is no help to the person who grabs the one at this marking.

  2. Q.02

    The risk diamond on a hazardous material label has 4 colored segments. What does the blue segment rate?

    FAA-H-8083-30B, ch. 1, p. 1-2

    1. AHow easily the material burns
    2. BHow much harm the material does to health
    3. CHow violently the material reacts with others
    SHOW THE ANSWER

    THE ANSWER IS B.

    How much harm the material does to health

    The risk diamond uses red for flammability, yellow for reactivity, blue for health and white for a special hazard. The flammability, reactivity and health segments each carry a number from 0, little or no hazard, up to 4, very hazardous.

  3. Q.03

    You are starting a piston engine with its electric starter. When should the radios and other electrical equipment that the start does not need be switched on?

    FAA-H-8083-30B, ch. 1, p. 1-12

    1. AOnce the generators are supplying power to the aircraft bus
    2. BBefore cranking, so the battery can be checked under a load
    3. CAs soon as the engine fires, before the starter is released
    SHOW THE ANSWER

    THE ANSWER IS A.

    Once the generators are supplying power to the aircraft bus

    During the start the battery, or a ground power unit, carries the whole load of the starter, which is why external power is used when it can be. Anything else switched on adds to that burden. So equipment the start does not need stays off until the generators are furnishing power to the bus. Turning it on before cranking, or while the starter is still engaged, loads the battery just when it can least spare it.

  4. Q.04

    Electric ground power units come towed, stationary or self-propelled. What does a self-propelled unit usually offer compared with a towed one?

    FAA-H-8083-30B, ch. 1, p. 1-21

    1. AA lower price than a towed unit, since no tug is needed to move it
    2. BPower from high-capacity batteries, suited to starting light aircraft
    3. CA wider range of output voltages and frequencies, at a higher price
    SHOW THE ANSWER

    THE ANSWER IS C.

    A wider range of output voltages and frequencies, at a higher price

    Self-propelled power units normally cost more than towed units, and in most cases they supply a wider range of output voltages and frequencies. Battery power alone describes the smallest towed units, which are simply high-capacity batteries for starting light aircraft, and saving the tug does not make the self-propelled kind the cheaper one to buy.

  5. Q.05

    A transport airplane is about to be towed into the hangar. Its entry door is open with the boarding ladder down, and the gear-down locks are still in their bag. What should be done before it moves?

    FAA-H-8083-30B, ch. 1, p. 1-19

    1. AClose the door, retract the ladder and install the gear-down locks
    2. BLeave the door open for the person on the brakes, and fit the locks once parked
    3. CFit the gear-down locks only, since the door and ladder do not matter when towing
    SHOW THE ANSWER

    THE ANSWER IS A.

    Close the door, retract the ladder and install the gear-down locks

    To avoid injury to people and damage to the aircraft during a tow, the entrance doors are closed, the ladders are retracted and the gear-down locks are installed before it moves. An open door or a lowered ladder sticks out where it can be struck as the airplane is moved, and the locks keep the gear from folding during the tow itself, so fitting them only after parking leaves the whole move unprotected.

  6. Q.06

    You are about to fuel a light airplane over the wing when a jet in the next row starts taxiing out, blowing grit and dust across the ramp toward you. What should you do?

    FAA-H-8083-30B, ch. 1, p. 1-27

    1. AFuel quickly, and close the cap on each tank as soon as it is full
    2. BHold off fueling until dirt is no longer blowing toward the airplane
    3. CCarry on, since the fuel filters will catch any dirt that gets in
    SHOW THE ANSWER

    THE ANSWER IS B.

    Hold off fueling until dirt is no longer blowing toward the airplane

    Blown dirt and dust can get into an open tank and contaminate everything in it, so fueling waits while another aircraft is blowing debris your way. Working faster still leaves each tank open to it while you fill. Counting on the filters gets it backward: the best way to control contamination is to keep it out of the fuel system in the first place, since filters and screens remove most of it, not all.

  7. Q.07

    You are walking backward ahead of a taxiing airplane, giving the pilot signals. What else should you be doing?

    FAA-H-8083-30B, ch. 1, p. 1-20

    1. AWatching the pilot's eyes without looking away, so no signal is missed
    2. BNothing more, since the pilot stays responsible until the engine stops
    3. CGlancing behind you often, so you do not trip or back into a propeller
    SHOW THE ANSWER

    THE ANSWER IS C.

    Glancing behind you often, so you do not trip or back into a propeller

    You are walking backward with your attention on the pilot, so you cannot see what is behind you. You must glance behind you often, or you can back into a propeller or trip over a chock, a fire bottle, a tie-down line or anything else in the way. Keeping the pilot in sight matters, but not to the point of never looking back, and the pilot being responsible for the airplane does nothing for your own footing.

  8. Q.08

    A fuel truck is topping off an airplane, and the crew asks you to service its gaseous oxygen system at the same time to save a few minutes. What should you do?

    FAA-H-8083-30B, ch. 1, p. 1-24

    1. AWait until the fueling is finished before servicing the oxygen
    2. BGo ahead, as long as 2 people handle the oxygen servicing
    3. CGo ahead, as long as the airplane and truck are grounded first
    SHOW THE ANSWER

    THE ANSWER IS A.

    Wait until the fueling is finished before servicing the oxygen

    Oxygen does not burn by itself, but it makes anything combustible catch fire faster and burn harder, so oxygen servicing is kept apart from fuel vapor and anything that could start a fire. It is not done during fueling, defueling or other work that could be a source of ignition. Using 2 people for oxygen servicing and grounding for fueling are both required, but neither makes it safe to run the 2 jobs at once.

  9. Q.09

    A reciprocating engine will not start. You follow the normal starter duty cycle, cranking for the full time allowed each try and cooling for the shortest time allowed. How long after the first try begins can the third try begin?

    FAA-H-8083-30B, ch. 1, p. 1-13

    1. A6 minutes
    2. B8 minutes
    3. C12 minutes
    SHOW THE ANSWER

    THE ANSWER IS B.

    8 minutes

    Crank for no more than 1 minute, then let the starter cool for 3 to 5 minutes. The first try runs to the 1 minute mark, cooling takes it to 4, the second try to 5 and the next cooling to 8. So the third try can begin 8 minutes after the first one began. Counting only the cooling time gives 6, and taking the longest cooling time of 5 minutes gives 12.

  10. Q.10

    Fuel controls can be blocked by solid particles a small fraction the width of a human hair. Taking a hair as 0.003 inch across, how small a particle can do that damage?

    FAA-H-8083-30B, ch. 1, p. 1-26

    1. A0.0015 inch
    2. B0.06 inch
    3. C0.00015 inch
    SHOW THE ANSWER

    THE ANSWER IS C.

    0.00015 inch

    A speck 1/20 the diameter of a human hair is enough to damage or plug the close-fitting parts of a fuel control. 0.003 divided by 20 is 0.00015 inch. Dividing by 2 instead of 20 gives 0.0015, and multiplying by 20 gives 0.06. Particles that small are why the filters, separators and screens matter so much.

We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.

04 AND THEN THE ORAL§ 65.79

How a missed code comes back at the oral

Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.I.F or AM.I.L. The examiner reads those codes before your oral and practical.

The General oral runs from 4 questions if your written was clean up to 22, because every code you missed adds 1 more. General also carries 9 practical projects, each with 2 questions attached.

Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.

05 COMMON QUESTIONSFAQ

Questions people ask about aircraft ground operations and servicing

Q.01

What are the classes of fire in aircraft maintenance?

Class A is ordinary combustible material such as wood, cloth and paper. Class B is flammable liquids such as fuel, oil and paint. Class C is energized electrical wiring and equipment, and the power comes off before anything else. Class D is burning metal, usually magnesium in the shop or in wheels and brakes, and water must never go on it: the metal reacts explosively.

Q.02

What is a hung start on a turbine engine?

The engine starts normally but the rpm stays at a low value instead of climbing to its normal starting speed. It is often the result of too little power reaching the starter. The start is shut down and the cause found before another try.

Q.03

How are aviation fuels told apart?

Avgas is identified by its grade, such as 100LL, the low lead grade, and by a color code, and the color of the fuel should match the color band on the piping and the fueling equipment. Jet fuel is marked black on piping and equipment, though the fuel itself can be clear or straw colored. Jet fuel added to avgas cuts the power the engine makes.

Q.04

What is foreign object damage, and how is it prevented?

Any damage to aircraft, people or equipment caused by a loose object: broken runway concrete, a shop towel, a piece of safety wire, a forgotten tool. It is prevented by keeping the ramp and work areas clean, running a tool control program, and giving used hardware and shop towels somewhere to go other than the floor.

Q.05

How many aircraft ground operations and servicing questions are on the FAA A&P General test?

The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Ground Operations and Servicing subject area 5 to 15% of the General test, which is 3 to 9 of the 60 scored questions. That is a range, not a quota, so your own test can land anywhere inside it. Our Safety, Ground Operations and Servicing questions also reach into Human Factors (5 to 10%).

Q.06

Which FAA handbook chapter covers aircraft ground operations and servicing?

Chapter 1 of FAA-H-8083-30B, the Aviation Maintenance Technician Handbook: General, titled "Safety, Ground Operations, & Servicing". It runs from pages 1-1 to 1-28, and the FAA publishes the whole handbook free as a PDF.

FREE PLAN · NO CARD · 25 QUESTIONS TO START

The bank holds 246 aircraft ground operations and servicing questions.

Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.

Start free

Or answer a few first. The free FAA A&P practice test runs on the page, with no account.