PrepAMT Academy

AMG · GEN-14 · FAA-H-8083-30B CH. 14

FAA A&P General: Human Factors

For the FAA A&P General test, human factors in aviation maintenance is chapter 14 of FAA-H-8083-30B, Human Factors. Its ACS subject area, Human Factors, is 5 to 10% of the test, or 3 to 6 of its 60 scored questions. Our question bank holds 227 questions on it, and the 10 below were written for this page.

Test shares and most-missed codes read from the FAA on 15 November 2026.

01 WHAT IT COVERSFAA-H-8083-30B · CH. 14

What FAA-H-8083-30B chapter 14 covers

Chapter 14 is about the person doing the work. It explains what human factors are and how the field grew up, then the models used to think about them, among them the PEAR model, and how human error happens and how it can be managed rather than only blamed.

The core of it is the Dirty Dozen, the 12 human factors that most often lead to maintenance errors, with what each one looks like on the hangar floor and how to guard against it. It closes with where to read further.

It runs from pages 14-1 to 14-32 of the Aviation Maintenance Technician Handbook: General, which the FAA publishes free as a PDF.

02 SHARE OF THE TESTFAA-G-ACS-1 · BLUEPRINT

How much of the FAA A&P General test it is

  • 5 to 10%OF THE TESTACS area AM.I.L
  • 3 to 6QUESTIONSof 60 scored
  • 227IN OUR BANKquestions on this subject

The FAA’s Companion Guide to the ACS gives every subject area a range, not a count. Human Factors (AM.I.L) is 5 to 10% (3 to 6 questions) on the 60-question General test. The 12 ranges for the General test add up to anywhere from 60% to 130%, so they say how big an area can get, not how many questions you will see from it.

Human Factors is not ours alone to cover: our Safety, Ground Operations and Servicing questions are written to the same area.

No code in this area is on the FAA’s latest list of most-missed codes (2nd Quarter, CY25), which names a code only when it was missed more than 70% of the time on at least 100 tests.

03 EXAMPLE QUESTIONSWRITTEN FOR THIS PAGE

Human factors in aviation maintenance questions and answers

10 questions in the test’s own format, each with 3 options and 1 correct answer. Pick yours, then open it to see the answer and the reason. Each one names the page it was written from, so you can check it.

  1. Q.01

    In the 1990s culture change at U.S. airlines, TWA started a new program. What did it set out to improve, and with what result?

    FAA-H-8083-30B, ch. 14, p. 14-9

    1. AThe layout of its job cards, which cut the number of skipped steps
    2. BTalks between the maintenance union and management, which improved quality
    3. CHangar lighting and heating, which cut sick leave among night crews
    SHOW THE ANSWER

    THE ANSWER IS B.

    Talks between the maintenance union and management, which improved quality

    The culture change at U.S. carriers in the 1990s was mostly about communication and collaboration. Continental began CRM-type training for mechanics, United kept inspectors closer to the work, Southwest built a strong, clear structure led by its CEO, and TWA started a program to improve communication between its maintenance trade union and maintenance management, which improved quality.

  2. Q.02

    A shop training lead is listing outside sources on human factors. What is the International Ergonomics Association?

    FAA-H-8083-30B, ch. 14, p. 14-31

    1. AA federation of over 40 ergonomics and human factors societies around the world
    2. BThe FAA office that sets the human factors rules for repair stations
    3. CA United States society of 22 technical groups, including one on aerospace systems
    SHOW THE ANSWER

    THE ANSWER IS A.

    A federation of over 40 ergonomics and human factors societies around the world

    The International Ergonomics Association is a federation of more than 40 ergonomics and human factors societies around the world, and every member of the Human Factors and Ergonomics Society is automatically a member of it. So it is a worldwide body, not a single United States society: the U.S. organization dedicated to the profession is the Human Factors and Ergonomics Society, formed in 1957. Nor is it an FAA office, though the FAA does run its own human factors website.

  3. Q.03

    A mechanic who has worked steady nights for a year finds that the same hangar noise and heat bother him far more than they did on days. What explains it?

    FAA-H-8083-30B, ch. 14, p. 14-17

    1. AHangars are louder and hotter at night, when most heavy work is scheduled
    2. BHe has stopped paying attention, which is a sign of complacency
    3. CRegular night shift work makes the body more sensitive to disturbances
    SHOW THE ANSWER

    THE ANSWER IS C.

    Regular night shift work makes the body more sensitive to disturbances

    Shift work puts technicians to work during the low part of their circadian rhythm and makes it harder to sleep off the job. Regular night work also makes the body more sensitive to environmental disturbances such as noise and heat, and it can wear down performance, morale and safety. The hangar is no louder or hotter than it was; what has changed is his body. Complacency is a different problem, false confidence on a familiar task.

  4. Q.04

    A 62-year-old inspector and a 24-year-old apprentice share a poorly lit bench. Under the PEAR model, how does the handbook treat better task lighting for them?

    FAA-H-8083-30B, ch. 14, p. 14-9

    1. AAs an Environment item only, so their ages make no difference
    2. BAs most important for the apprentice, who has less experience to fall back on
    3. CAs a People concern too, and one that matters most for the older inspector
    SHOW THE ANSWER

    THE ANSWER IS C.

    As a People concern too, and one that matters most for the older inspector

    The handbook lists proper lighting for the task as a People consideration that also ties in with the Environment element, and it says this matters especially for older workers. So lighting is not an Environment matter only, and the age that counts here is the inspector's, not the apprentice's lack of experience. The next sentence adds annual vision and hearing exams as a way to keep physical performance at its best.

  5. Q.05

    A mechanic arrives with a bad flu but feels well enough to finish rigging the elevator cables. Why does working while ill count against the quality of the job?

    FAA-H-8083-30B, ch. 14, p. 14-25

    1. ABeing ill is a psychological stressor, the same as money worries
    2. BThe body spends energy fighting the illness, leaving less for the work
    3. CIt counts only if the medicine taken is the kind that causes drowsiness
    SHOW THE ANSWER

    THE ANSWER IS B.

    The body spends energy fighting the illness, leaving less for the work

    Poor physical condition is one of the physiological stressors, along with fatigue, hunger and disease. Trying to work when ill or not feeling well forces the body to use more energy fighting the illness, which leaves less energy for the tasks that matter. Feeling well enough does not change that. Money and family worries are psychological stressors, a different group, and the handbook ties the problem to the illness itself, not to any medicine.

  6. Q.06

    A pair of mechanics are handed the same tight deadline. One works on calmly, while the other grows anxious and starts to make slips. What does this show about stress?

    FAA-H-8083-30B, ch. 14, p. 14-24

    1. AThat the anxious mechanic must be less skilled than the calm one
    2. BThat the same situation can be a stressor for one person and not another
    3. CThat a deadline is a physical stressor, like heat, noise or poor light
    SHOW THE ANSWER

    THE ANSWER IS B.

    That the same situation can be a stressor for one person and not another

    Everyone handles stress differently, and the same situation can be harder for one person than another: a strict timeline can be a stressor for one technician and normal for the next. That says nothing about skill. Physical stressors are things in the work environment such as temperature, noise, lighting and cramped spaces, while worry about getting a repair done on time is a work-related psychological stressor.

  7. Q.07

    Partway through a job you find that the maintenance manual leaves out a step you need. After getting the right information from technical support, why should you also report the gap?

    FAA-H-8083-30B, ch. 14, p. 14-21

    1. AUnless someone points out missing information, nothing is done to correct the manual
    2. BThe FAA requires manual errors to be reported in writing within 24 hours of being found
    3. CReporting it lets you sign the job off without carrying out the missing step
    SHOW THE ANSWER

    THE ANSWER IS A.

    Unless someone points out missing information, nothing is done to correct the manual

    When needed information is missing, ask a supervisor, a technical representative or the manufacturer's publications department. Manuals are in a constant state of revision, and if nobody identifies what is missing, nothing is done to correct them, so the next mechanic hits the same gap. Reporting it changes nothing about how you finish and sign for your own job.

  8. Q.08

    Mechanics working winter nights in an unheated, dimly lit hangar tell their manager the cold and poor light are slowing them down and causing mistakes. How does the handbook say a company should handle conditions like these?

    FAA-H-8083-30B, ch. 14, p. 14-10

    1. ALeave it to each mechanic to dress warmly and bring a flashlight
    2. BWork with the workforce to either accommodate the conditions or change them
    3. CWait until the conditions cause a reported error, then look at them
    SHOW THE ANSWER

    THE ANSWER IS B.

    Work with the workforce to either accommodate the conditions or change them

    The physical environment covers temperature, humidity, lighting, noise control, cleanliness and workplace design. Companies must acknowledge these conditions and cooperate with the workforce to either accommodate them or change them, and that takes a corporate commitment, such as portable heaters, task lighting and suitable clothing. Leaving it to each mechanic ignores the company's part, and waiting for a reported error means acting only after harm is done.

  9. Q.09

    A repair station's managers want fewer sick days and better productivity from their mechanics. Which step have many companies taken that did both?

    FAA-H-8083-30B, ch. 14, p. 14-9

    1. AShortening breaks so jobs finish sooner and staff go home earlier
    2. BRotating the mechanics through the night shift each week
    3. CMaking healthy meals, snacks and drinks available to employees
    SHOW THE ANSWER

    THE ANSWER IS C.

    Making healthy meals, snacks and drinks available to employees

    A good human factors program looks after the physical and mental health of the people who do the work. Many companies have cut sick leave and raised productivity by making healthy meals, snacks and drinks available. Shorter breaks work against the planned rest a good program builds in, and rotating shifts disrupt the circadian rhythm and can degrade performance.

  10. Q.10

    What led Transport Canada to draw up its list of 12 human factors that can lead to maintenance errors?

    FAA-H-8083-30B, ch. 14, p. 14-13

    1. AMany maintenance-related accidents and incidents in the late 1980s and early 1990s
    2. BA new FAA rule that every repair station must give its mechanics a yearly human factors course
    3. CA study of the mistakes pilots made when flying in bad winter weather in Canada
    SHOW THE ANSWER

    THE ANSWER IS A.

    Many maintenance-related accidents and incidents in the late 1980s and early 1990s

    The handbook says Transport Canada drew up the 12 factors because of the large number of maintenance-related aviation accidents and incidents in the late 1980s and early 1990s. They are human factors that degrade people's ability to work effectively and safely and can lead to maintenance errors, and the industry later adopted the list as a simple way to talk about human error in maintenance. It grew out of maintenance events, not pilot errors, and it is not an FAA rule.

We wrote these questions for this page from the FAA handbooks. They are not FAA test questions, and none of them comes from our question bank. Each one names the handbook page it was written from, so you can check it.

04 AND THEN THE ORAL§ 65.79

How a missed code comes back at the oral

Your test report does not show the questions you missed. It prints the ACS code for what each one tested, and a question missed in this subject prints a code that starts AM.I.L. The examiner reads those codes before your oral and practical.

The General oral runs from 4 questions if your written was clean up to 22, because every code you missed adds 1 more. General also carries 9 practical projects, each with 2 questions attached.

Knowledge elements are tested on the written test and the oral; Risk Management elements are tested on the oral and the practical; Skill elements are tested on the practical only. The whole process is on the oral and practical page, and there are cards to practice the spoken half with on FAA A&P oral test practice questions.

05 COMMON QUESTIONSFAQ

Questions people ask about human factors in aviation maintenance

Q.01

What is the Dirty Dozen in aviation maintenance?

The 12 human factors that Transport Canada identified, after the maintenance accidents of the late 1980s and early 1990s, as the ones that most degrade a mechanic’s work: lack of communication, complacency, lack of knowledge, distraction, lack of teamwork, fatigue, lack of resources, pressure, lack of assertiveness, stress, lack of awareness and norms.

Q.02

What does PEAR stand for in human factors?

People, Environment, Actions and Resources: the people who do the job, the environment they work in, the actions they perform, and the resources they need to complete it. It is a memory aid for the 4 things a maintenance human factors program has to consider.

Q.03

What are norms in the Dirty Dozen?

Norms are the way things are normally done: unwritten rules that most organizations follow or tolerate. A negative norm can pull a shop away from its own safety standard without anyone deciding it should, so the answer is to work to the written procedure, not to how it is usually done.

Q.04

How does complacency lead to errors?

It develops over time. As a mechanic gains experience, self satisfaction and false confidence can set in, and a task done many times without ever finding a fault gets skimmed or skipped. A fault may still be there, however rarely, so the item gets the same look every time.

Q.05

How many human factors in aviation maintenance questions are on the FAA A&P General test?

The FAA does not publish a fixed number. Its Companion Guide to the ACS gives the Human Factors subject area 5 to 10% of the General test, which is 3 to 6 of the 60 scored questions. That is a range, not a quota, so your own test can land anywhere inside it.

Q.06

Which FAA handbook chapter covers human factors in aviation maintenance?

Chapter 14 of FAA-H-8083-30B, the Aviation Maintenance Technician Handbook: General, titled "Human Factors". It runs from pages 14-1 to 14-32, and the FAA publishes the whole handbook free as a PDF.

FREE PLAN · NO CARD · 25 QUESTIONS TO START

The bank holds 227 human factors in aviation maintenance questions.

Start with one free set: 25 questions and 25 fill-in-the-gaps from any of our 44 subjects, which cover every ACS subject area. Each question has 3 answer choices, like the FAA A&P tests, with a written explanation behind every answer and, for every answer written from the FAA handbooks, the chapter it came from. It needs no card. Pro opens the rest of the bank, the full study guides and the timed mock papers.

Start free

Or answer a few first. The free FAA A&P practice test runs on the page, with no account.